EUROC ARGO TECTOR
6 TO 26 t
REPAIR MANUAL
www.WorkshopManuals.co.uk
This publication describes the characteristics, data and correct
methods for repair operations on each component of the ve-
hicle.
If the instructions provided are followed and the specified
equipment is used, correct repair operations in the pro-
grammed time will be ensured, safeguarding against possible
accidents.
Before starting to perform whatever type of repair, ensure that
all accident prevention equipment is available and efficient.
All protections specified by safety regulations, i.e.: goggles,
helmet, gloves, boot, etc. must be checked and worn.
All machining, lifting and conveying equipment should be in-
spected before use.
The data contained in this publication was correct at the time
of going to press but due to possible modifications made by
the Manufacturer for reasons of a technical or commercial na-
ture or for adaptation to the legal requirements of the differ-
ent countries, some changes may have occurred.
No part of this publication, including the pictures, may be re-
produced in any form or by any means.
Publication Edited by:
IVECO S.p.A.
T.C.O. - B.U. Customer Service
Lungo Stura Lazio 49
10156 Torino (Italy)
Print 603.93.231 - 1st Ed. 2003
B.U. TECHNICAL PUBLISHING
C.so Svizzera, 185
10149 Torino (Italy)
Publication Produced by:
www.WorkshopManuals.co.uk
Workshop Manuals - concerning the mechanical part - are divided into several Sections. Each Section is characterised by a number
and its content is shown on the general index to be found at the beginning of each workshop manual.
Each section deals generally with one of the main Assemblies (engine, transmission, etc.)
Each section deals with the following topics:
Specifications and technical data, Tightening torques, Special tools, Troubleshooting (fault diagnosis), Component removal/refitting,
Repair operations.
To facilitate manual consultation, the different subjects are generally dealt with (where possible), following the same sequence.
This manual also provides graphs and symbols instead of description of parts, operations or operating procedures (see next page),
to give a more immediate and friendly reference.
Example:
Ø 1 = Housing for connecting rod small end bush
Ø 2 = Housing for big end bearings
Furthermore, within each section, every heading or sub-heading concerning the operations to be carried out is preceded by a six
digit number. This number is the Product Code that is to be found in the repair operation described in the FLAT RATE MANUALS
and in the FAILURE CODES publication.
For quick reference the indication for reading this code is described below (see also the Flat Rate Manuals).
Product code:
The first two figures identify the PRODUCT within the vehicle.
Example :
Product 50 = Frame;
Product 52 = Axles;
Product 53 = Gearbox, etc.
Assembly code:
Figure three and four identify the ASSEMBLY within the PRODUCT
Example :
Product 50 = Frame;
Assembly 01 = Chassis;
Assembly 02 = Bumpers-Under run-bars, etc.
Subassembly code:
Figure five and six identify exactly the SUB-ASSEMBLY and the Assembly Component within the PRODUCT
Example :
Product 50 = Frame;
Assembly 01 = Chassis;
Subassembly 40 = Chassis cross members, etc.
α
Tighten to torque + angle value
1 ∅
∅ 2
5 0
PRODUCT ASSEMBLY SUBASSEMBLY
COMPONENT
0 1
PRODUCT ASSEMBLY SUBASSEMBLY
COMPONENT
4 0
PRODUCT ASSEMBLY SUBASSEMBLY
COMPONENT
Print 603.93.231 Base - July 2003
SPECIAL REMARKS
www.WorkshopManuals.co.uk
Base - July 2003 Print 603.93.231
Graph and symbols
Removal
Disconnection
Intake
Refitting
Connection
Exhaust
Removal
Disassembly
Operation
Fitting in place
Assembly
ρ
Compression ratio
Tighten to torque
Tolerance
Weight difference
α
Tighten to torque + angle value Rolling torque
Press or caulk
Replacement
Original spare parts
Regulation
Adjustment
Rotation
!
Warning
Note
Angle
Angular value
Visual inspection
Fitting position check
Preload
Measurement
Value to find
Check
Number of revolutions
Equipment Temperature
Surface for machining
Machine finish bar
Pressure
Interference
Strained assembly
Oversized
Higher than….
Maximum, peak
Thickness
Clearance
Undersized
Less than….
Minimum
Lubrication
Damp
Grease
Selection
Classes
Oversizing
Sealant
Adhesive
Temperature < 0 °C
Cold
Winter
Air bleeding
Temperature > 0 °C
Hot
Summer
www.WorkshopManuals.co.uk
Print 603.93.231 Base - July 2003
EUROCARGO Tector 6-26 t
Print 603.93.231 - 1
st
edition
Base - July 2003
UPDATING DATE
Section Description Page Revision date
www.WorkshopManuals.co.uk
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$35.99
IVECO Truck LORRY WAGON EUROCARGO TECTOR 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 ton se
Viewed 10 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$35.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
Iveco Eurocargo Tector 6-26 tons Workshop manual contains over 1200 pages of detailed information. This manual is a valuable resource for both professional mechanics and DIY enthusiasts. It covers a wide range of sections including General specifications, Engine, Clutch, Gearbox, Propeller shafts, Rear axles, Front axles, Suspension, Wheels and tires, Pneumatic system, Body-chassis, and Programmed maintenance.
