DUCATI MONSTER 695 Bike Workshop Repair Service Manual

How to use the manual 1 - How to use the manual This manual has been prepared for Ducati Authorized Service Centers and workshop personnel involved in the maintenance and repair of Ducati motorcycles. It gives fundamental information on how to work in perfect harmony with the concepts of “good technique” and “safety on work sites” for servicing or replacing of original spare parts both for chassis and engine concerning this motorcycle. All operations described in this manual must be carried out by senior skilled technicians, who are requested to strictly follow the Manufacturer’s instructions. Some information has been intentionally omitted, as, at our advice, a specialized technician must have this technical background. Additional information on how to install the different components is provided in the spare parts catalogue. Caution This manual also describes pre-delivery checks. Ducati Motor Holding S.p.A. declines all responsibility for any technical errors or omissions in this manual and reserves the right to make changes without prior notice. The information given in this manual was correct at the time of going to print. Caution Reproduction and disclosure of all or part of the contents of this manual are strictly forbidden without prior written authorization of Ducati Motor Holding S.p.A. All rights on this manual are reserved for Ducati Motor Holding S.p.A. Applications for authorization must be submitted in writing and must specify the reasons for reproduction or disclosure. Ducati Motor Holding S.p.A. Manual layout This manual is divided in sections (1), each identified by a letter. Each section (1) includes several chapters (2), which are numbered consecutively. file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_1_3_00.3.1.html (1 of 2) [10/7/2008 8:41:32 PM]

How to use the manual Each chapter (2) may include several paragraphs (3). The repair procedures described in this manual include the necessary disassembly and reassembly instructions, i.e. the full procedure is detailed starting with the motorcycle fully assembled until bringing it back to the original condition. Caution Some of the sections of this manual are not present, being the relevant parts not installed on the vehicle. Caution The manual structure has been designed to be applied to all the different models manufactured by DUCATI MOTOR HOLDING. To make reading easier, the sub-sections table of contents is kept unchanged for all models. file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_1_3_00.3.1.html (2 of 2) [10/7/2008 8:41:32 PM]

Symbols - abbreviations - references 2 - Symbols - abbreviations - references For easy and rational reading, this manual uses graphic symbols for highlighting situations in which maximum care is required, practical advice or simple information. Please pay maximum attention to these symbols as they are meant to avoid repeating technical concepts or safety rules throughout the text. These symbols must be considered as “hints” to important information. Please refer to this page whenever in doubt as to their meaning. Left-hand and right-hand in the descriptions refer to motorcycle direction of travel. Warning Failure to follow the instructions given in text marked with this symbol can lead to serious personal injury or death. Caution Failure to follow the instructions in text marked with this symbol can lead to serious damage to the motorcycle and its components. Note This symbol indicates additional useful information for the current operation. Text references (X) The bold reference indicates a part that is not illustrated in the figures next to the text, but can be found in the exploded view at the beginning of each section. (X) The non-bold reference indicates a part that is illustrated in the figures next to the text. Product specifications Symbols inside the diagram show the type of threadlocker, sealant or lubricant to be used at the points indicated. The table below shows the symbols together with the product specifications. Symbol Specifications Recommended product Engine oil (for specifications, see sect. C 2, Fuels and lubricants). SHELL Advance Ultra 4 DOT 4 special hydraulic brake fluid. SHELL Advance Brake DOT 4 SAE 80-90 gear oil or special products for chains with O-rings. SHELL Advance Chain or Advance Teflon Chain file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_2_3_00.4.1.html (1 of 3) [10/7/2008 8:41:38 PM]

Symbols - abbreviations - references Anti-freeze (nitride, amine and phosphate free) 30-40% water solution. SHELL Advance coolant or Glycoshell GREASE A Multipurpose, medium fiber, lithium grease. SHELL Alvania R3 GREASE B Molybdenum disulphide grease, high mechanical stress and high temperature resistant. SHELL Retinax HDX2 GREASE C Bearing/joint grease for parts subject to prolonged mechanical stress. Temperature range: -10 to 110° C. SHELL Retinax LX2 GREASE D Protective grease. Corrosion protectant, waterproof. SHELL Retinax HD2 GREASE E PANKL grease PLB 05. GREASE F OPTIMOL - PASTE WHITE T. Grease LOCK 1 Low-strength threadlocker. Loctite 222 LOCK 2 Medium-strength threadlocker, compatible with oil. Loctite 243 LOCK 3 High-strength sealant for threaded parts. Loctite 270 LOCK 4 Flange sealant. Resistant to high mechanical stress, solvents and high temperatures (up to 200°C). For pressures up to 350 atm. Fills gaps up to 0.4 mm. Loctite 510 LOCK 5 Permanent adhesive for smooth or threaded cylindrical fasteners on mechanical parts. High resistance to mechanical stress and solvents. Temperature range: -55 to 175°C. Loctite 128455 LOCK 6 Pipe sealant for pipes and medium to large fasteners. For water and gases (except oxygen). Maximum filling capacity: diameter gaps up to 0.40 mm. Loctite 577 file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_2_3_00.4.1.html (2 of 3) [10/7/2008 8:41:38 PM]

Symbols - abbreviations - references LOCK 7 Speed bonder for rubber and plastics. Elastomer loaded ethylic base. Loctite 480 LOCK 8 High-strength retaining compound for threaded parts, bearings, bushes, splines and keys. Temperature range: -55 to 150 ° C. Loctite 601 LOCK 9 Medium-strength threadlocker. Loctite 401 LOCK 10 Product for metal parts to seal and lock freely sliding parallel or threaded couplings. Resistant to high mechanical stress and high temperature, solvent-proof and chemical-proof. Loctite 128443 LOCK 11 Instantaneous jelly sealant featuring tensile / cut strength. Loctite 454 gel DUCATI liquid gasket 942470014 Exhaust pipe paste. Self-curing sealant, hardens when heated. For temperatures over 1,000°C. Fire gum holts Spray used in treating electrical systems to eliminate moisture and condensation. Provides high resistance to corrosion. Waterproof. SHELL Advance Contact Cleaner Dry lubricant that polymerizes in the air Molycote D321R file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_2_3_00.4.1.html (3 of 3) [10/7/2008 8:41:38 PM]

Dangerous products – warnings 3 - Dangerous products – warnings General safety rules Carbon oxide When a maintenance operation must be performed with the engine running, position the motorcycle out of doors or in a well-ventilated area. Never operate the engine in an enclosed place. Warning Exhaust emissions contain carbon oxide, which is a poisonous gas and may lead to loss of conscience or even death. Operate the engine out of doors or, if working indoors, use an exhaust emission extraction plant. Fuel Always make sure the area is well ventilated. Do not smoke near the motorcycle or the area where fuel is stored and keep any sources of ignition, such as flames or sparks, well away from motorcycle and fuel storage area. Warning The fuel used to operate engines is highly flammable and becomes explosive under particular conditions. Keep away from children. Hot component parts Warning The engine and exhaust component parts become hot when the engine is running and will stay hot for some time after the engine has been stopped. Wear heat gloves before handling these components or allow for the engine and exhaust system to cool down before proceeding. Warning The exhaust system will stay hot for some time after the engine has been stopped. Do not touch these components with your body and do not park the vehicle near flammable materials (including wood, leaves...). Used engine oil Warning Prolonged or repeated contact with engine oil may cause skin cancer. If exposed to engine oil on a daily basis, make it a rule to wash your hands thoroughly with soap right after handling engine oil. Keep away from children. Brake lining debris file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_3_3_00.5.1.html (1 of 2) [10/7/2008 8:41:41 PM]

Dangerous products – warnings Never attempt to clean the brake assembly using compressed air or a dry brush. Brake fluid Warning Avoid spilling brake fluid onto plastic, rubber or paint-finished parts or they will damage. Protect these parts with a clean shop cloth before proceeding to service the motorcycle. Keep away from children. Battery Warning The battery gives off explosive gases. Keep away from sources of ignition, such as sparks and flames. Do not smoke near the battery. Make sure the area is well ventilated when charging a battery. General maintenance indications A word of advice Ducati would like to suggest that you follow the instructions below so to ensure an efficient, fault-free motorcycle operation. - When diagnosing breakdowns, primary consideration should always be given to what the customer reports. Your questions to the customer should aim at clarifying the problem. - Diagnose the problem systematically and accurately before proceeding further. This manual provides the theoretical background for troubleshooting that should be combined with personal experience and attendance at Ducati training courses. - Repair work should be planned carefully in advance to prevent any unnecessary downtime, for example picking-up of required spare parts or arrangement of required tools, etc. - Time and money can be saved by limiting the number of operations needed to reach the part to be repaired. The disassembly procedure in this manual describes the most efficient way to reach a part to be repaired. General advice on repair work - Always use top quality tools. Lift the motorcycle only with devices in full compliance with relevant European directives. - During repair work always keep the tools within reach, possibly in the right order. Never put them on the vehicle or in hardly reachable places or somehow hidden. - Work place must be neat and clean. - During repair work always change gaskets, seals and split pins. - When loosening or tightening nuts and bolts, always start with the largest and always start from the center. Tighten nuts and bolts working crossways; tighten to the specified torque. - At disassembly, mark any parts and positions which might easily be confused at reassembly. - Use Ducati original spare parts only. Use the recommended lubricants only. - Use special service tools where specified. - Ducati Technical Bulletins often contain updated versions of the service procedures described in this manual. Check the latest Bulletins for details. file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_A_3_3_00.5.1.html (2 of 2) [10/7/2008 8:41:41 PM]

Description 0Description 1 - How to use the manual 3 Manual layout 4 2 - Symbols - abbreviations - references 5 Product specifications 6 3 - Dangerous products – warnings 8 General safety rules 8 General maintenance indications 9 file:///C|/Documents%20and%20Settings/F4i/My%20D...i%20manual/wsm/usa/Mon695_MY07_A_IND_00.2.1.html [10/7/2008 8:41:43 PM]

Identification data 1 - Identification data Identification data for Monster 695 i.e. Each Ducati motorcycle has two identification numbers - frame number and engine number, and an EC nameplate (A) (not used in the USA version). file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_B_1_1_00.7.1.html (1 of 4) [10/7/2008 8:41:45 PM]

Identification data Note The frame and engine numbers identify the motorcycle model; please state these numbers when ordering spare parts. Data punched on frame European version 1 Manufacturer’s name: Ducati Motor Holding 2 Type – same on all Monsters 3 Variant 4 Version 5 Year of manufacture (7=2007) 6 Plant of manufacture 7 Progressive serial No. file:///C|/Documents%20and%20Settings/F4i/My%...0manual/wsm/usa/Mon695_MY07_B_1_1_00.7.1.html (2 of 4) [10/7/2008 8:41:45 PM]

You're Reading a Preview

DUCATI MONSTER 695 Bike Workshop Repair Service Manual

Description

Reviews

Q&A

Recently Viewed