WH6 - WH7
00-1
CONTENTS
CONTENTS
Pagina
10. STRUCTURE AND FUNCTION ...................................................................................... 10-1
20. TESTING AND ADJUSTING ........................................................................................... 20-1
30. DISASSEMBLY AND ASSEMBLY ................................................................................. 30-1
90. OTHER...................................................................................................................... 90-1
PAGE INTENTIONALLY
LEFT BLANK
WH6 - WH7
00-3
REVISED PAGES
REVISED PAGES
The affected pages are indicated by the use of the fol-
lowing marks. It is requested that necessary actions be
taken to these pages according to table below.
Pages having no marks are those previously revised or
made additions.
Mark Indication Action required
Q Page to be newly Add
q Page to be replaced Replace
( ) Page to be delete Discard
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
00-1
00-2
00-3
00-4
00-5
00-6
00-7
00-8
00-9
00-10
00-11
00-12
00-13
00-14
00-15
00-16
00-17
00-18
00-19
00-20
00-21
00-22
00-23
00-24
10-1
10-2
10-3
10-4
10-5
10-6
10-7
10-8
10-9
10-10
10-11
10-12
10-13
10-14
10-15
10-16
10-17
10-18
10-19
10-20
10-21
10-22
10-23
10-24
10-25
10-26
10-27
10-28
10-29
10-30
10-31
10-32
10-33
10-34
10-35
10-36
10-37
10-38
10-39
10-40
10-41
10-42
10-43
10-44
10-45
10-46
10-47
10-48
10-49
10-50
10-51
10-52
10-53
10-54
10-55
10-56
10-57
10-58
10-59
10-60
10-61
10-62
10-63
10-64
10-65
10-66
10-67
10-68
10-69
10-70
10-71
10-72
10-73
10-74
10-75
10-76
10-77
10-78
10-79
10-80
10-81
10-82
10-83
10-84
10-85
10-86
10-87
10-88
20-1
20-2
20-3
20-4
20-5
20-6
20-7
20-8
20-9
20-10
20-11
20-12
20-13
20-14
20-15
20-16
20-17
20-18
20-19
20-20
20-21
20-22
20-23
20-24
20-25
20-26
20-27
20-28
20-29
20-30
20-31
20-32
20-33
20-34
20-35
20-36
20-37
20-38
20-39
20-40
20-41
20-42
20-43
20-44
20-45
20-46
20-47
20-48
20-49
20-50
20-51
20-52
20-53
20-54
20-55
20-56
20-57
20-58
20-59
20-60
20-61
20-62
20-63
20-64
20-65
20-66
20-67
20-68
20-69
20-70
20-71
20-72
20-73
20-74
20-75
20-76
20-77
20-78
20-79
20-80
20-81
20-82
20-83
20-84
20-85
20-86
20-87
20-88
20-89
20-90
20-91
20-92
20-93
20-94
20-95
20-96
20-97
20-98
WH6 - WH7
00-4
REVISED PAGES
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
20-99
20-100
20-101
20-102
20-103
20-104
20-105
20-106
20-107
20-108
20-109
20-110
30-1
30-2
30-3
30-4
30-5
30-6
30-7
30-8
30-9
30-10
30-11
30-12
30-13
30-14
30-15
30-16
30-17
30-18
30-19
30-20
30-21
30-22
30-23
30-24
30-25
30-26
30-27
30-28
30-29
30-30
30-31
30-32
30-33
30-34
30-35
30-36
30-37
30-38
30-39
30-40
30-41
30-42
30-43
30-44
30-45
30-46
30-47
30-48
30-49
30-50
30-51
30-52
30-53
30-54
30-55
30-56
30-57
30-58
30-59
30-60
30-61
30-62
30-63
30-64
30-65
30-66
30-67
30-68
30-69
30-70
30-71
30-72
30-73
30-74
30-75
30-76
30-77
30-78
30-79
30-80
30-81
30-82
30-83
30-84
30-85
30-86
30-87
30-88
30-89
30-90
30-91
30-92
30-93
30-94
30-95
30-96
30-97
30-98
30-99
30-100
30-101
30-102
30-103
30-104
30-105
30-106
30-107
30-108
30-109
30-110
30-111
30-112
30-113
30-114
30-115
30-116
30-117
30-118
30-119
30-120
30-121
30-122
30-123
30-124
30-125
30-126
30-127
30-128
30-129
30-130
30-131
30-132
30-133
30-134
30-135
30-136
30-137
30-138
30-139
30-140
30-141
30-142
30-143
30-144
30-145
30-146
30-147
30-148
30-149
30-150
30-151
30-152
30-153
30-154
30-155
30-156
30-157
30-158
30-159
30-160
30-161
30-162
30-163
30-164
30-165
30-166
30-167
30-168
30-169
30-170
30-171
30-172
30-173
30-174
30-175
30-176
30-177
30-178
30-179
30-180
30-181
30-182
30-183
30-184
30-185
30-186
30-187
30-188
30-189
30-190
30-191
30-192
30-193
30-194
30-195
30-196
30-197
30-198
30-199
30-200
30-201
30-202
30-203
30-204
30-205
30-206
30-207
30-208
30-209
30-210
30-211
30-212
30-213
30-214
30-215
30-216
30-217
30-218
30-219
30-220
30-221
30-222
30-223
30-224
30-225
30-226
30-227
30-228
30-229
30-230
30-231
30-232
30-233
30-234
30-235
30-236
30-237
30-238
30-239
30-240
30-241
30-242
30-243
30-244
30-245
30-246
30-247
30-248
30-249
30-250
30-251
30-252
30-253
30-254
30-255
30-256
30-257
30-258
30-259
30-260
30-261
30-262
30-263
30-264
30-265
30-266
30-267
30-268
30-269
30-270
30-271
30-272
30-273
30-274
30-275
30-276
30-277
30-278
30-279
30-280
30-281
30-282
30-283
30-284
90-1
90-2
90-3
90-4
90-5
90-6
WH6 - WH7
00-5
k SAFETY
k IMPORTANT SAFETY NOTICE
Proper service and repair is extremely important for the safe operation of your machine.
The service and repair techniques recommended by Komatsu Utility and describe in this manual are both ef-
fective and safe methods of operation. Some of these operations require the use of tools specially designed
by Komatsu Utility for the purpose.
To prevent injury to workers, the symbol k is used to mark safety precautions in this manual. The cautions
accompanying these symbols should always be carefully followed. If any danger arises or may possibly arise,
first consider safety, and take necessary steps to face.
GENERAL PRECAUTIONS
Mistakes in operation extremely dangerous.
Read all the Operation and Maintenance Manual carefully
BEFORE operating the machine.
1. Before carrying out any greasing or repairs, read all
the precautions written on the decals which are suck
on the machine.
2. When carrying out any operation, always wear safety
shoes and helmet. Do not wear loose work clothes, or
clothes with buttons missing.
• Always wear safety glasses when hitting parts
with a hammer.
• Always wear safety glasses when grinding parts
with a grinder, etc.
3. If welding repairs are needed, always have a trained,
experienced welder carry out the work. When carrying
out welding work, always wear welding gloves, apron,
glasses, cap and other clothes suited for welding
work.
4. When carrying out any operation with two or more
workers, always agree on the operating procedure be-
fore starting. Always inform your fellow workers be-
fore starting any step of the operation. Before starting
work, hang UNDER REPAIR signs on the controls in
the operator’s compartment.
5. Keep all tools in good condition and learn the correct
way to use them.
6. Decide a place in the repair workshop to keep tools
and removed parts. Always keep the tools and parts in
their correct places. Always keep the work area clean
and make sure that there is no dirt or oil on the floor.
Smoke only in the areas provided for smoking. Never
smoke while working.
PREPARATIONS FOR WORK
7. Before adding or making any repairs, park the ma-
chine on hard, level ground, and block the wheels to
prevent the machine from moving.
8. Before starting work, lower outrigger, bucket or any
other work equipment to the ground. If this is not pos-
sible, use blocks to prevent the work equipment from
falling down. In addition, be sure to lock all the control
levers and hang warning sign on them.
9. When disassembling or assembling, support the ma-
chine with blocks, jacks or stands before starting
work.
10. Remove all mud and oil from the steps or other places
used to get on and off the machine. Always use the
handrails, ladders or steps when getting on or off the
machine.
Never jump on or off the machine.
If it is impossible to use the handrails, ladders or steps,
use a stand to provide safe footing.
PRECAUTIONS DURING WORK
11. When removing the oil filler cap, drain plug or hydrau-
lic pressure measuring plugs, loosen them slowly to
prevent the oil from spurting out.
Before disconnecting or removing components of the
hydraulic circuit and engine cooling circuit, first re-
move the pressure completely from the circuit.
12. The water and oil in the circuits are not hot when the
engine in stopped, so be careful not to get burned.
Wait for the oil water to cool before carrying out any
work on the cooling water circuits.
13. Before starting work, remove the leads from the bat-
tery. Always remove the lead from the negative ( – )
terminal first.
k SAFETY
WH6 - WH7
00-6
k SAFETY
14. When raising heavy components, use a hoist or
crane. Check that the wire rope, chains and hooks
are free from damage.
Always use lifting equipment which has ample ca-
pacity. Install the lifting equipment at the correct
places.
Use a hoist or crane and operate slowly to prevent
the component from hitting any other part.
Do not work with any part still raised by the hoist or
crane.
15. When removing covers which are under internal
pressure or under pressure from a spring, always
leave two bolts in position on opposite sides. Slowly
release the pressure, then slowly loosen the bolts to
remove.
16. When removing components, be careful not to
break or damage the wiring.
Damage wiring may cause electrical fires.
17. When removing piping, stop the fuel or oil from spill-
ing out. If any fuel or oil drips on to the floor, wipe it up
immediately.
Fuel or oil on the floor can cause you to slip, or can
even start fires.
18. As a general rule, do not use gasoline to wash parts.
In particular, use only the minimum of gasoline when
washing electrical parts.
19. Be sure to assemble all parts again in their original
places. Replace any damage parts with new parts.
When installing hoses and wires, be sure that they
will not be damaged by contact with other parts
when the machine is being operated.
20. When installing high pressure hoses, make sure
that they are not twisted. Damaged tubes are dan-
gerous, so be extremely careful when installing
tubes for high pressure circuits. Also, check that
connecting parts are correctly tightened.
21. When assembling or installing parts, always use
specified tightening torques.
When installing the parts which vibrate violently or
rotate at high speed, be particulary careful to check
that they are correctly installed.
22. When aligning two holes, never insert your fingers or
hand.
23. When measuring hydraulic pressure, check that the
measuring tool is correctly assembled before taking
any measurement.
24. Take sure when removing or installing wheels.
WH6 - WH7
00-7
FOREWORD
FOREWORD
This shop manual has been prepared as an aid to improve the quality of repairs by giving the operator an accurate
understanding of the product and by showing him the correct way to perform repairs and make judgements. Make sure
you understand the contents of this manual and use it to full effect at every opportunity.
This shop manual mainly contains the necessary technical information for operations performed in a service work-
shop.
The manual is divided into chapters on each main group of components; these chapters are further divided into the
following sections.
STRUCTURE AND FUNCTION
This section explains the structure and function of each component. It serves not only to give an understanding
of the structure, but also serves as reference material for troubleshooting.
TESTING AND ADJUSTING
This sections explains checks to be made before and after performing repairs, as well as adjustments to be
made at completion of the checks and repairs.
Troubleshooting charts correlating «Problems» to «Causes» are also included in this section.
DISASSEMBLY AND ASSEMBLY
This section explains the order to be followed when removing, installing, disassembling or assembling each
component, as well as precautions to be taken for these operations.
NOTE
The specifications contained in this shop manual are subject to change at any time and without any no-
tice.
Contact your Komatsu Utility distributor for the latest information.
WH6 - WH7
00-8
HOW TO READ THE SHOP MANUAL
HOW TO READ THE SHOP MANUAL
VOLUMES
Shop manual are issued as a guide to carry out repairs.
These various volumes are designed to avoid duplicat-
ing the same information.
DISTRIBUTION AND UPDATING
Any additions, amendments or other changes will be
sent to Komatsu Utility distributors.
Get the most up-to-date information before you start any
work.
FILING METHOD
1. See the page number on the bottom of the page.
File the pages in correct order.
2. Following examples show you how to read the page
number.
Example:
3. Additional pages: additional pages are indicated by
a hyphen (–) and number after the page number.
Fle as in the example.
Example:
REVISED EDITION MARK
When a manual is revised, an edition mark is recorded
on the bottom outside corner of the pages.
REVISIONS
Revised pages are shown on the LIST OF REVISED
PAGES between the title page and SAFETY page.
SYMBOLS
In order to make the shop manual greatly chelpful, im-
portant points about safety and quality are marked with
the following symbols.
10 3
Item number (10. Structure and
Function)
Consecutive page number for each
item
-
10-4
10-4-1
10-4-2
10-5
Added pages
Symbol Item Remarks
k Safety
Special safety precautions
are necessary when
performing the work.
Extra special safety precautions
are necessary when performing
the work because it is under in-
ternal pressure.
a Caution
Special technical precautions or
other precautions for preserving
standards are necessary when
performing the work.
4 Weight
Weight of parts or systems.
Caution necessary when select-
ing hoisting wire, or when work-
ing posture is important, etc.
3
Tightening
torque
Parts that require special atten-
tion for the tightening torque dur-
ing assembly.
2 Coat
Parts to be coated with adhe-
sives and lubricants etc.
5 Oil, water
Places where oil, water or fuel
must be added, and their quan-
tity.
6 Drain
Places where oil or water must
be drained, and quantity to be
drained.
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$46.99
Komatsu WH609-716 Telescopic Handlers Workshop Repair Service Manual
Viewed 34 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$46.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
This is a comprehensive Service and Repair Manual for the Komatsu WH609-716 Telescopic Handlers. It is suitable for both professional mechanics and DIY enthusiasts. The manual covers a wide range of repair procedures and is compatible with all versions of Windows, Mac, iOS, BB, Android, etc. It is also printable for easy reference.
Service Repair Manual Covers:
- Engine overhaul and rebuilding
- Brakes
- Sunroof
- Timing belt replacement
- Trouble codes
- Wiring diagrams
- Troubleshooting and diagnostics
- Computer diagnostic trouble tree charts
- Engine performance
- Front end and alignment procedures and specifications
- Suspension
- Transmission removal and installation
- Air conditioning service and capacities
- Transmission in-car servicing
- Computer diagnostic codes
- Firing orders
- Detailed specifications on every model covered
- Factory maintenance schedules and charts
- Serpentine belt routings with diagrams
- Timing belt service procedures
- Brake servicing procedures
- Driving concerns
- Complete torque specifications
- U-joint and CV-joint service procedures
- Repair procedures
- Complete wiring diagrams
- Hundreds of illustrations
- Vacuum diagrams
Additional Information:
- Instant delivery with no shipping costs
- No waiting for a paper or CD manual to arrive in the mail
