TECUMSEH PEERLESS TRANSAXLE VST205 Series Factory Service & Work Shop Manual

TECUMSEH / PEERLESS MOTION DRIVE SYSTEM TRANSMISSIONS / TRANSAXLES / DIFFERENTIALS / RIGHT ANGLE DRIVES T E C H N I C I A N ’ S H A N D B O O K TECUMSEH This manual covers all Peerlessﬁ Gear models as follows: Right Angle and T Drives (P-91), 100, 600, 601, 700, 800, 801, 820, 900, 910, 915, 920, 930, 940, 1000, 1100, 1200, 1300, 1800, 2300, 2400, 2500, 2600, 2800, MST, VST.

TABLE OF CONTENTS Page CHAPTER 1. GENERAL INFORMATION SECTION 1. Model Overview and Terms Used ................................................................ 1 - 6 SECTION 2. Lubrication Requirements .................................................................................. 7 SECTION 3. Identifications ..................................................................................................... 8 SECTION 4. Torque Specifications ......................................................................................... 9 SECTION 5. Trouble Shooting Table ............................................................................ 10 - 12 CHAPTER 2. TRANSMISSIONS SECTION 1. 700 Series ................................................................................................ 13 - 16 SECTION 2. 700H Series .............................................................................................. 17 - 19 SECTION 3. 2800 Series .............................................................................................. 20 - 21 CHAPTER 3. TRANSAXLES SECTION 1. 600 Series ............................................................................................... 22 - 26 SECTION 2. 601 Slow Speed Series ................................................................................... 27 SECTION 3. 800/801 Series ......................................................................................... 28 - 32 SECTION 4. 820 Series ................................................................................................ 33 - 36 SECTION 5. 900 Series ................................................................................................ 37 - 40 SECTION 6. 910 Series ................................................................................................ 41 - 44 SECTION 7. 915 Series / 940 Series ............................................................................ 45 - 48 SECTION 8. 920 Series ................................................................................................ 49 - 52 SECTION 9. 930 Series ................................................................................................ 53 - 56 SECTION 10. MST200 Series ....................................................................................... 57 - 62 SECTION 11. VST205 Series ....................................................................................... 63 - 64 CHAPTER 4. 3-SPEED TRANSAXLES SECTION 1. 1200 Series .............................................................................................. 65 - 67 CHAPTER 5. FOUR-SPEED TRANSAXLES SECTION 1. 2300 Series .................................................................................................. 68 - 73 CHAPTER 6. REDUCTION GEAR and DIFFERENTIAL UNIT SECTION 1. 1300 Series .................................................................................................. 74 - 75 CHAPTER 7. REDUCTION GEAR and DIFFERENTIAL UNITS SECTION 1. 2400 Series .................................................................................................. 76 - 77 SECTION 2. 2500 Series .................................................................................................. 78 - 81 SECTION 3. 2600 Series .................................................................................................. 82 - 84 CHAPTER 8. DIFFERENTIALS ......................................................................................... 85 - 90 CHAPTER 9. DRIVES ........................................................................................................ 91 - 95 1100 Series ....................................................................................................................... 96 - 98 CHAPTER 10. SHIFTING ASSEMBLY ............................................................................ 99 - 101 CHAPTER 11. BEARING and BUSHING SERVICE ...................................................... 102 - 103 C Tecumseh Products Company 1996 NOTE: The VST Series is not addressed in this issue with the exception of the brake.

1 CHAPTER 1. SECTION 1. MODEL OVERVIEW AND TERMS USED A. TECUMSEH / PEERLESS UNITS 1. GENERAL Tecumseh/Peerless makes power transmission gear drives for use in all types of lawn and garden equipment. 2. IDENTIFICATION OF MODELS Since acquisition by Tecumseh Products Co. in 1964, all Peerless assemblies have a model number identification tag, or stamping. On units containing axles (transaxles, or reduction gear and differential units) the identification should be visible by viewing the case/cover unit from below and behind as it is mounted in the driven equipment. If the area is dirt or oil covered, however, some cleaning may be necessary. Write down any numbers found in locations pointed out, then compare with the Master Parts Manual Div. 8 index. For right angle and “T” drives, the identification number is stamped into the housing under the input shaft boss opposite the cover. On transmissions the identification number is stamped on the cover back of the output drive sprocket. On the 100 series differential, the number is stamped either on cast housing diameter or on the housing end near axle bushing. 3. TRANSAXLES A combination of transmission and differential axle are in one compact unit. Peerless transaxles are manufactured in many different gear ratio combinations and from 1 to 7 forward speeds with one reverse. A. 600 Series. The 600 series is a lightweight unit usually used in riding mower or similar application. The 600 series has a vertical input shaft at the top of the case. The case is aluminum, contributing to a considerable weight saving. Variations in the series (which determines the specific model number such as 603, 603A, 609, etc.) includes: 1. Shift lever shape. 2. Axle lengths. 3. Axle machining for wheel hub attachment. 4. Axle housing variations. 5. Size of the brake shaft. There may be other slight differences, however, these are present as a result of product improvement which are not options to an O.E.M. (Original Equipment Manufacturer). B. 800 Series. This unit has 3 to 6 speeds forward and 1 reverse. The bearings are oil impregnated bushings with needle bearings or ball bearings on axles, input and output shaft. C. 820 Series. This unit is a heavy duty unit with 2 to 6 speeds forward and 1 reverse which can be used with ground engagement attachments. Sleeved needle bearings are used in place of oil impregnated bushings on all shaft ends and ball bearings are standard on axles. D. 900 Series. The unit is like the 800 series transaxle except that the 900 can be 2, 3, or 4 speeds forward and 1 reverse. E. 910 Series. This transaxle will offer a forward and reverse unit. The speed will change with the use of a vari-drive pulley arrangement. F. 915 Series. This unit has 3 to 5 speeds forward and 1 reverse. This unit has a gear driven reverse instead of chain driven and the case is sculpted around the gears. G. 920 Series. This series of 900 transaxle offers 3 to 7 speeds forward and 1 reverse. H. 930 Series. This unit has 3 to 7 speeds for ward and 1 reverse. The transaxle is very similar to the 920 series except for the differential and shifter/brake shaft. I. The MST Series, (Manual Shift Transaxle) 200 is a sealed unit which uses 16 oz. of 80W90 gear lube (part #730229A). The MST series is available with up to 6 speeds forward and one reverse. It has a sculptured case and cover. J. VST/1800 Series . This transaxle incorporates a hydrostatic pump and motor built into the unit. The prefix letters stand for Variable Speed Transaxle (VST). This unit contains two separate oil reservoirs, one for the pump and motor containing airless synthetic oil and the other contains EP90 gear oil for the differential gears. This unit sealed for life and not serviceable at this time. K. 1200 Series. The distinguishing feature of the 1200 series transaxles is that the axle support housings are pressed from the inside of the case and cover, therefore, are not readily removable until the unit is completely disassembled. The casing is cast iron for rugged, longtime wear.

2 L. 2300 Series. Generally similar to the 1200 series transaxle. The distinguishing features are a more massive casing, and a larger shift lever opening machined area. The obvious difference from the standpoint of application is that these units have four speeds forward and will be found on equipment that can be used with ground engagement operations. NOTE: The transaxles described in paragraphs K and L, are fairly similar in appearance, but do have specific recognizable characteristics. Both these units have cast iron bodies for rugged application, although the 2300 series is the only unit that can be used in ground engaging equipment applications. 3. REDUCTION GEAR AND DIFFERENTIAL UNITS GENERAL These units do not have a transmission function characteristic of transaxles, but rather, are units to reduce input speed and torque to a suitable axle speed and torque. The hydrostatic units which match to these units perform the transmission function. a. 1300 Series. This unit is the hydrostatic counterpart of the three-speed forward unit (1200). It has an aluminum casing and pressed through axle support housings, characteristic of the 1200 series. The hydrostatic unit is of Eaton manufacture and is not serviced by Tecumseh Service Dealers. b. 2400, 2500 & 2600 Series. This series of hydrostatically driven reduction gear and differential units can be used in ground engaging operations such as plowing. The hydrostatic unit is manufactured by Sundstrand Corp. in LaSalle, Ill. 3. TRANSMISSIONS These units as manufactured by Peerless consist of the shifting mechanism to take a constant input shaft speed and reduce it to the desired output speed. The differential or axle unit is connected through a chain drive. a. 700 Series. This unit can be 3, 4 or 5 speeds forward and 1 reverse. The brake system can be mounted on either side of the unit. b. 700 “H” Series. This unit is built with almost all interchangeable parts with in it’s two cases except that this will be a “H” shift pattern. This unit has 3 or 4 speeds forward and 1 reverse. c. 2800 Series. This unit is built to work on the 2600 series. It is used as a P.T.O. transmission to run external equipment. 4. DIFFERENTIALS The only self contained differential/axle unit built by Peerless is the 100 series. It features hardened axle shafts of various length and machined for various methods of hub attachment. The case is cast aluminum and the differential gears are sintered metal or cut steel. The differential pin is held in place by the four retaining capscrews. Oil Lite bushings reduce friction during differential operation. The drive sprocket is part of the unit, which depending upon application, can be in any of several diameters in size, thus having a different number of gear teeth. This sprocket is often supplied by the O.E.M. 5. ANGLE DRIVES These units are used primarily to change the direction of drive at the point where the working equipment attaches. They can be assembled for right or left hand rotation so that they can be used in various combinations for synchronous operation. a. Right Angle Drive. These units consist of input shafts, output shafts, and the beveled gearing necessary to change the direction of power transmission at right angles. By positioning the drive bevel gear on the input shaft nearest the input end, opposite rotation will be attained from that of switching the beveled gear around to the side away from the input end of the shaft. Casing and bearings are identical. A cover identifies each unit as being either a left hand (LH) or a right hand (RH) right angle drive. b. “T” Drives. The “T” drive is essentially the same as the right angle drive except that the input shaft extends out the other side of the case to transmit power in the same line to additional right angle drives or other equipment. c. Shafts, Couplings, Pulleys, etc. These items are part of the total transmission unit and are used to connect angle drives, and other attachments. The serrated couplings match the serrations on the shafts of the angle drives or on connecting shafts. 6. TERMS USED AXLE - The shaft which connects the wheel or hub to the differential unit and transmits force back to the wheels. Sometimes axle refers to the differential and axle combination as in the term TRANSAXLE. AXLE HOUSING (or AXLE SUPPORT) - An extension of the case and cover to support the outer ends of the axles. Because the housing is visible, it is often the best means of distinguishing the series in question. BEARING BLOCK (Strip) - Used to support the ring gear of the differential. BEVEL (on a gear - different from bevel gear) - Roundness of the meshing sides of gear teeth allow easy shifting. Because this is about the only allowance made to make easier shifting, the unit should be stopped before the shift to keep these spur gears from getting chewed up.

3 BEVEL GEAR - A gear with teeth ground on a diagonal so that when it meshes with a second bevel gear, power is transmitted at an angle. If the angle is 90 o , the gear is known as a MITER GEAR. BEVEL PINION - The smaller of two meshed bevel gears in a gear train. BRAKE (or BRAKESHAFT) - The shaft on a Peerless unit (Transaxles and Transmission) to which a braking system may be attached. It is in the gear train with the differential to stop it when the operator “brakes”. It is usually larger in diameter than the in put shaft due to its function of taking shock loads experienced in braking. CASE - That part of the unit “casing half” which contains the shift lever and input shaft openings. The other “half” is the COVER because the reassembly must be done into one or the other depending upon the series. CHAMFER - Diagonal milling at the corners of gear teeth to remove sharp edges. The usual reason for chamfer is to eliminate the possibility of hardened gears chewing softer metal. COUNTERSHAFT - Splined shaft which holds gears that are in constant mesh with shift gears and transfer power flow from input to shift gears. COUPLING - A sleeve to connect two serrated shafts in the same axial plane. Used in right angle drive systems or in connecting the hydrostatic drive to the input shaft on 2400 series transaxles. COVER - That part of the unit “casing half” which contains the brake shaft opening (except the 600 series in which all openings are in the CASE as described in CASE above). The case and the cover switch sides depending upon whether the transaxle is right or left hand drive. DIFFERENTIAL GEAR BOLTS - Through bolts holding the differential parts together. The heads of these bolts must be opposite the output shaft gear (except in the 2400 series). This is an early check to see that the unit is being assembled correctly. DOWEL PIN - Alignment pin is used to align the case and cover and other parts in a transmission or transaxle. The dowel should be tapped in to hold the parts in alignment before tightening the retaining screws. Failure to install dowel pins first will usually lead to a unit that binds after assembly. DUO-TRAK* DIFFERENTIAL (*Trademark -Illinois Tool Works) - A type of differential which increases torque to the tractive wheel to keep it turning, however in situations where differentiation is necessary (as in turning) the unit acts much like a regular differential. EQUIPMENT - The complete assembly (riding mower, tractor, etc.) is built by a manufacturer, a part of which is the Peerless unit. A check of the equipment manual is recommended prior to servicing the Peerless unit. HEAD ASSEMBLY - A complete unit containing all parts of one right angle or “T” drive assembly of a right angle drive system. The head assembly is permanently lubricated and sealed. IDENTIFICATION NUMBER - See MODEL NUMBER IDLER - A gear used in a gear train to transfer motion or direction. The gear rotates independently of the shaft upon which it is located. INPUT OR INPUT SHAFT - The part of a Peerless unit which is always connected to the drive. Its rotational speed is dependent on the driving mechanism. All parts of the input system are always in mesh with input shaft and turn whenever it turns. LIMITED SLIP DIFFERENTIAL - See DUO-TRAK* DIFFERENTIAL. MITER GEAR - One of a pair of interchangeable bevel gears with axles at right angles. Since all bevel gears are miter gears in Peerless units, the terms can be the same. MODEL NUMBER - The identifying number of a Peerless unit which will permit selection of the proper parts to repair that unit. NEUTRAL SPACER - Single or split collar between forward gears and reverse that shift keys engage when unit is in neutral. OIL SEAL, DOUBLE LIP - An oil seal with two sealing surfaces to prevent entrance of foreign matter, and leakage of lubricant. OIL SEAL, QUAD RING - A seal with two external and two internal sealing lips. Used in the shifter housing. OIL SEAL, SINGLE LIP - An oil seal with one sealing surface to either prevent entrance of foreign matter or prevent leakage of lubricant. OUTPUT, OR OUTPUT SHAFT - On a transaxle, the shaft that contains the output pinion which is in direct mesh with and drives the differential. In a transmission, the exposed shaft which contains the sprocket for driving the axles. The output shaft is driven by the large OUTPUT GEAR. OUTPUT SHAFT GEAR - The importance of defining this gear is to point out that it must be opposite the differential bolts in Peerless units (except the 2400 series). The output gear assembles into transaxle cover. PEERLESS UNIT OR UNITS - The complete Peerless assembly which is part of the EQUIPMENT. The Peerless unit is that assembly being described. REDUCTION GEAR AND DIFFERENTIAL UNIT - A Peerless unit that reduces a high RPM input speed to a suitable axle speed without the use of a transmission. Since there is a single gear train, there is a single input speed to output speed ratio, however, axle speeds are infinite, depending upon input speed.

4 REVERSE IDLER (915 Series) - Gear between reverse gear of countershaft and reverse gear of shifter/brake shaft that allows unit to operate in opposite direction. REVERSE IDLER - A gear added to the gear train so when in mesh, reverses the direction of all gears driven after it. Its number of teeth also affects the reverse gear ratio. The center gear of the three gear cluster always is in mesh with the REVERSE IDLER, and the large shifter gear always shifts into it. RIGHT ANGLE DRIVE - Interchangeable with HEAD ASSEMBLY. The major operating parts are a pair of miter gears. A system consists of other right angle or “T” drive head assemblies and connecting hardware. SEAL - A mechanism which stops leakage. It can be a rubber ring, as in an “O” ring or “Quad” ring, a sealing type ball bearing, or most commonly, a rubber- like sealing surface encased in a metal form. SEAL RETAINER - Found on some models of transaxles and on right angle drives. The center of the retainer is bored to the size of the outer diameter of the seal. On transaxles the retainer acts to position the differential. In the casing on right angle drives, it acts as the end cap of the case and is secured with four capscrews. SHIFT COLLAR - Round collar which retains shift keys onto the shifter/brake shaft. The shifter assembly pin (or pins) slide into the groove on the collar to activate the shift keys. SHIFT GEARS - Gears on shifter/brake shaft that are in constant mesh with spur gears of counter shaft. The shift gear in which the shift keys engage determines the speed of a transaxle. SHIFT KEY - One of either two or four metal spring steel keys, which are held in the keyways of the shifter/brake shaft, by a shift collar. The shift keys are used to slide through the shift gears and engage the desired gear or speed. SHIFT KEYWAY - One of either two or four slots in the shifter/brake shaft for the shift keys to slide through for gear selection. SHIFT WASHER - Washer on which one side has a 45 o inner diameter chamfer or rounded inner diameter. Shift washers depress keys for shifting from one gear to another. SHIFTER ASSEMBLY - Consists of shift rod, shift fan, shift arms and shift pin or pins. SHIFT LEVER - The lever by which the operator manually changes the shifter gears to vary reduction speed ratios in the transmission. The configuration of the lever is variable and is often the only reason for a unit being given a new model number. SHIFTER FORK - A mechanical arm which moves on rod to position the shifter gear at an exact spot axially along the shifter shaft. SHIFTER GEAR, LARGE - This gear transmits 1st (low) and reverse (1st, 2nd and reverse in 4- speed units) gear ratio force to the output shaft. It is beveled on both sides. SHIFTER GEAR, SMALL - This gear transmits 2nd and 3rd (3rd and 4th in a 4-speed unit) gear ratio force to the output shaft. It can have two different tooth diameters and be beveled on the outside of each, or it can have a beveled spline to engage 3rd (or 4th) gear through a splined shaft. SHIFTER HOUSING - This housing contains the shift lever and must be reinstalled in the proper position to function correctly. If housing does not already have guide marks, scribe the shifter housing and transmission case before removal. SHIFTER ROD - One of two similar smooth rods of equal length with grooves which match the fork position to meshed positions of the shifter gears and gears of the three gear cluster. Each rod has a snap ring to act as a fork stop, but can also be used to determine how the fork is assembled to it. SHIFTER SHAFT - A splined shaft which meshes with the internal splines of the shifter gears, to transmit force to the output shaft gear. SHIFTER STOP - A stamped metal plate which separates the shifter forks. The stop has a notch cut in it which corresponds to the neutral position on the shifter forks and rod. The shifter lever must return the engaged fork back to neutral before it can cross to actuate the other fork. SPROCKET - A geared wheel designed to turn a link chain drive. Various numbers of teeth (hence, sprocket diameter) are available to change output ratios. SPUR GEAR - A gear having the shaft bore and teeth in a parallel plane. “T” DRIVE - A right angle drive with an input shaft extending thru the case to transmit power axially in a second direction to the right angle output. On “T” drive with dissimilar input and out end of the input shaft, care must be taken to insure that the parts do not run in reverse when reassembled. THREE GEAR CLUSTER - A 3 gear assembly in mesh with the input shaft. The gears are of different sizes to change gear ratios when meshing with the two shifter gears. THRUSTER RACE - A thrust washer in which the outer edge is cupped to fit the outer diameter of a thrust bearing. This fit positions the thrust race concentric with the axle diameter. It further acts as a thrust washer. THRUST WASHER - A flat polished surface separating metals of different hardness. It also acts as a spacer between shafts and the case and cover.

5 TRANSMISSION - A system of varying sized gears in a case, some of which can be slid along a shaft to vary gear ratio in the gear train. The net effect is to change speeds to the rear wheel according to the type of work being done. UNIT - See PEERLESS UNIT. 8. GENERAL SERVICING PROCEDURES 1. Introduction: The following service procedures should be understood and practiced whenever service must be performed on a Peerless unit. 2. Before removal of unit from equipment, look for: a. Loose drive belts. b. Improperly adjusted or badly worn clutch. c. Loose or lost set screws and/or sheared keys in drive and driven pulleys. d. Oil saturated drive belts and clutches. e. Bad operating habits, such as clutch riding. f. Oil leaks. If found, refer to paragraph F. g. Any trouble, which might be pointed up by operating the unit and equipment, IF POSSIBLE. h. Review Service Bulletin 304. 3. Removal of the Peerless unit from the equipment: a. Jack up equipment so that transaxle is accessible. Use wood blocks to prevent equipment movement. Do not use bricks, cement or cinder blocks. b. Visually inspect Peerless unit for oil leaks, cracked housing, binding or rubbing of parts, or other symptoms of malfunction. c. Use a jack under the Peerless unit to support it’s weight when attachments are removed. d. Remove wheels, drive belts, pulleys, chains and other associated equipment from Peerless unit. Be aware of positioning of parts. Scribe mark, if in doubt, to be able to reassemble parts quickly. e. If shifter lever will interfere with unit in any way, remove it before unit is removed. f. Remove attaching hardware holding Peerless unit to equipment at case, cover, axle supports, shifter or by other means. g. With Peerless unit free and supported, remove it from the area of equipment to the work bench. 4. Preparing for disassembly: a. Visually inspect for evidence of oil seepage, tampering, misalignment, freedom of rotating shafts, etc. b. Clean unit thoroughly of dirt, oil, debris. c. Remove shift housing and drain oil from unit. Observe oil to see if metal particles are present. d. Check axle shafts carefully for smoothness. Use a stone or suitable abrasive to rub down high spots and eliminate rust or paint. e. Check model number at appropriate spot. It is advisable to have the exploded parts view handy. f. Have seal sleeves, driver, tools, shop cloths and informational material at hand. 9. OIL LEAKS, SEAL AND GASKET SERVICE Peerless units contain various styles and sizes of oil seals. The function of any oil seal can be: 1. To seal inward (single lip) to prevent lubricant leaks. 2. To seal outward (single lip) to prevent lubricant leaks. 3. To seal both inward and outward (double lip). Some seals are spring loaded. That is a spring creates a positive light compressing action to insure that the seal lip will make a 100 contact around the shaft. All Peerless seals, seal on the inner diameter. 1. Other than leaking seals, gaskets and “O” rings, leakage can occur due to a cracked case or cover, flats on shafts, porosity (rarely, if ever), and worn bushings and shafts. 2. Single lip inward sealing can be salvaged by the use of the proper seal protector when pulling the seal over a shaft. Outward sealing seal (both single and double lip) must be replaced since there is no assurance that the initial sealing surface can be protected. 3. If you can’t protect the sealing lip, replace the entire seal. The cost of the seal is small in comparison to a return repair due to reuse for seals. 4. Check seals for cracks, scuffs, cuts and distortion. Check seal areas for evidence of oil leak both at sealing surface and between metal-to-metal contact surface areas. 5. Some seals have a “Redicoat” sealant applied, while others may need a thin coat of this or a similar sealant. 6. The surface over which the seal lips must slide must be free of all cuts, scratches, high spots, or rust. The shafts should be smooth, shiny and a thin film of light oil applied. Sleeves should be used to clear keyways, splines, or other sharp edges machined into shafts. 10.TORQUE VALUES TROUBLE SHOOTING 1. All torque values must be applied. The torque value for any fastener will be found in the assembly instruction where that fastener is used. All torque specs. will be found in Section 4. 2. Overtightening can strip threads, compress the gasket excessively, and possibly cause binding. 3. Cross tightening sequence to half the torque then finally to full torque value. 4. Under tightening Oil leakage, loosening of attaching parts, and possible shifting of the internal parts causing complete failure.

6 5. Since all bolts are readily accessible there is no reason that a torque wrench cannot be used for all bolt and screw tightening. 11.TESTING The absence of binding and oil leakage are the best indications that the unit has been properly reassembled. Though other, more elaborate tests can be done, this would be the prerogative of the servicing agency, since the following checks are considered adequate. With the shift forks in neutral, rotate both axle ends in the same direction. They should turn smoothly although a little effort may be necessary. The brake shaft should rotate whenever the axles turn together, but in neutral, the input shaft should not turn. By moving any shifter gear into mesh, a greater drag should be felt on the axles, and both the input and brakeshaft should turn. For ease in turning of the various shafts, insert a tool (such as a punch or a socket head screw key) into the keyway, however, do not force if shaft is binding. Reason for unit binding: 1. Re-used or lack of gasket. 2. Oil seal retainers installed backward. 3. Mis-installed thrust washers. 4. Differential installed backwards. 5. Mis-assembly of shifting parts. 6. Mis-placement of spacers. 7. Foreign matter blocking gear teeth mesh. 8. Shifter stop installed backwards. 9. Input shaft not completely in case. 10. Mis-alignment of case and cover. Align with dowels before tightening cap screws.

7 SECTION 2. LUBRICATION CHART Check the Peerless unit model number before filling with lubricant. There may be a difference in the quantity recommended. This is dictated by the design of the vehicle and the position of the Peerless unit in it. TRANSMISSIONS Model No. Quantity 700 12 oz./355 ml Grease 700H 12 oz./355 ml Grease 2800 † TRANSAXLES Model No. Quantity 600 24 oz./710 ml Oil 800 30 oz./887 ml Grease 801 36 oz./1065 ml Grease 820 36 oz./1065 ml Grease 900 26 oz./769 ml Grease 910 18 oz./532 ml Grease 915 10 oz./296 ml Grease 920 30 oz./887 ml Grease 930 30 oz./887 ml Grease 1200 48 oz./1420 ml Oil †† 1305 1309 32 oz./946 ml Oil 1313 1301 1302 1303 1304 1306 1307 1308 1310 1311 1312 1314 1315 44 oz./1301 ml Oil 1316 1317 1318 1320 1321 1322 1325 1328 1329 1319 1323 24 oz./710 ml Oil 1326 1327 MST 16 oz./473 ml Oil 2300 64 oz./1892 ml Oil 2400 32 oz./946 ml Oil 2500 † 2600 † RIGHT ANGLE AND T DRIVES Model No. Quantity All Models Except * 4 oz./118 ml Grease *1408-P91 *1409-P91 *1410-P91 *3002 3 oz./89 ml Grease *3003 *3028 *3029 *3035 1000 Series 6 oz. / 180 ml SAE E.P. 80W90Oil 1100 16 oz./473 ml Oil DIFFERENTIALS All Models 3 oz./89 ml Grease TWO SPEED AXLE All Models 2 oz./59 ml Grease THREE SPEED AXLE All Models 2 oz./59 ml Grease NOTICE Grease: Bentonite Grease Part Number 788067B Oil: SAE E.P. 80W90 Oil Part Number 730229A † Refer to O.E.M. Mechanic’s Manual for type of lubricant †† To be filled through shift lever opening

8 SECTION 3. IDENTIFICATION Early Models were not identified with a model number on the unit. THE MODEL NUMBER WILL BE FOUND ON: A. Metal tag or decal attached to unit as illustrated. B. Stamped on unit as illustrated. Identification Number Locations SAMPLE (OLD STYLE) MOD 506 PEERLESS 1 275 1374 Individual Serial Number Manufactured on the 275th Day Manufactured in 1991 SAMPLE (NEW STYLE) MST205- l l l l l l l l l l l l l SERIAL 6 0 0 2 Serial Number Julian Date Specification Number Manufacturers Requested Features RIGHT ANGLE DRIVES 100 SERIES A or B A or B A or B 1200 SERIES 1100 SERIES 600 SERIES A or B 700 SERIES A 2600 SERIES A 2800 SERIES A A 810 SERIES 801 SERIES 900 SERIES 920 SERIES 930 SERIES A A 910 SERIES A 1300 SERIES A 820 SERIES A 915 SERIES A 2400 SERIES A or B 2300 SERIES A or B MST and VST 2500 SERIES A

TECUMSEH PEERLESS TRANSAXLE VST205 Series Factory Service & Work Shop Manual

You're Reading a Preview

Recently Viewed