No. SEF-0F7BE
FORKLIFT TRUCK
TCM CORPORATION
FHG15T3
FHG18T3
FG20T3
FHG20T3
FG25T3
FHG25T3
FG30T3
FHG30T3
FG35T3S
FHD15T3
FHD18T3
FD20T3
FHD20T3A
FD25T3
FHD25T3A
FD30T3
FHD30T3A
FD35T3S
SERVICE MANUAL
SERVICE MANUAL
FG20T3 – FG30T3, FHG15T3 – FHG30T3, FG35T3S
FD20T3 – FD30T3, FHD15T3, FHD20T3A – FHD30T3A, FD35T3S
No. SEF-0F7BE
No. SEF-0F7BE
FOREWORD
TCM’s new forklift trucks with capacities from 1.5 through 3.5 tons feature low operating noise and
reduced vibration as well as improved controllability and higher safety, and come equipped with new
high-performance engines.
The gasoline engines used for this series are equipped with an electronically-controlled fuel supply
unit to reduce emissions from the engine.
The steering system can correct steering wheel knob deviation automatically to provide better driver
control. The instrument panel accommodates optional OK monitors which allow the operator to check
the water level, air cleaner plugging, and battery condition of charge with just a glance. The serviceability
of these trucks has been greatly improved by these changes.
This Service Manual describes all of the major components and their service procedures. We
encourage you to make practical use of it while servicing the trucks.
We also hope you will understand that, due to on-going improvements of the parts and components,
the values and some of the descriptions in this manual are subject to change without notice.
February 2010
The specifications and equipment covered in this manual will vary according to the intended
destination. In our documents and manuals, these differences are coded according to the destination as
follows.
Export specification code Destination
EXA North America
EXB All regions excluding North America, EU member countries, Oceania and
South Africa
EXC Oceania
EXE EU member countries (excluding Scandinavia)
EXK South Africa
EXN Scandinavia
No. SEF-0F7BE
No. SEF-0F7BE
SPECIFICATIONS (1)
Truck model
Item
Performance
Max. load kg[lbs]
Basic load center mm[in.]
Lift height mm[in.]
Tilt angle (fwd-bwd) °
Free lift mm[in.] A
Lift speed mm/s[fpm]
(unloaded)
(loaded)
Traveling speed km/h[mph]
fwd 1st
2nd
rev 1st
2nd
Max. drawbar pull kN{kgf}[lbf]
(unload)
(loaded)
Gradeability
(unload)
(loaded)
Min. turning radius mm[in.] B
Min. 90° intersecting aisle mm[in.] C
Dimensions mm[in.]
Overall length D
Overall width E
Overall height
(at overhead guard) F
Overall height with
extended mast G
Wheelbase H
Tread
(front) J
(rear) K
Fork overhang L
Rear overhang M
Fork size
(Length (N) x Width (P) x Thickness (Q))
Fork spacing R
Under clearance (at frame)
Weight
Operating weight kg[lbs]
FHG15T3
1360 [3000]
600 [24]
3000 [118.1]
6 - 12
155 [6.1]
680 [133.9]
650 [127.9]
19.5 [12.1]
*
19.5 [12.1]
*
6.9 {700}
[1540]
15.7 {1600}
[3530]
1/5.5
1/3.0
1980 [78]
1780 [70.1]
3165 [124.6]
1070 [42.1]
2070 [81.5]
4250 [167.3]
1425 [56.1]
890 [35]
920 [36.2]
395 [15.6]
425 [16.7]
920 x 100 x 35
[36.2 x 3.9 x 1.4]
200 - 920
[7.9 - 36.2]
105 [4.1]
2510 [5530]
FHD15T3
660 [129.9]
620 [122.1]
18.6 {1900}
[4190]
2620 [5780]
FHG18T3
1580 [3500]
680 [133.9]
650 [127.9]
15.7 {1600}
[3530]
1/5.8
1/3.2
2010 [79.1]
1800 [70.9]
3195 [125.8]
1100 [43.3]
920 [36.2]
455 [17.9]
2670 [5580]
FHD18T3
660 [129.9]
620 [122.1]
18.6 {1900}
[4190]
2780 [6120]
No. SEF-0F7BE
SPECIFICATIONS (2)
FG20T3
1810 [4000]
600 [24]
3000 [118.1]
6 - 12
160 [6.3]
590 [116.3]
580 [114.2]
19.0 [11.8]
*
19.0 [11.8]
*
8.3 {850}
[1866]
16.7 {1700}
[3754]
1/5.0
1/3.5
2170 [85.4]
1920 [75.6]
3555 [140]
1150 [45.3]
2070 [81.5]
4250 [167.3]
1600 [63.0]
970 [38.2]
970 [38.2]
450 [17.7]
435 [17.1]
1070 x 122 x 40
[42.1 x 4.8 x 1.6]
245 - 1020
[9.65 - 40.2]
110 [4.33]
3210 [7080]
FHG20T3
640 [125.9]
620 [122.1]
22.1 {2250}
[5000]
1/5.6
1/2.8
3220 [7110]
FG25T3
2260 [5000]
590 [116.3]
580 [114.2]
16.7 {1700}
[3754]
1/5
1/4.2
2240 [88.2]
2010 [79.1]
3625 [142.7]
450 [17.7]
505 [19.9]
1070 x 122 x 40
[42.1 x 4.8 x 1.6]
3570 [7870]
FHG25T3
640 [125.9]
620 [122.1]
22.1 {2250}
[5000]
1/5.6
1/3.0
3580 [7890]
FG30T3
2720 [6000]
135 [5.3]
500 [98.4]
490 [96.4]
19.5 [12.1]
19.5 [12.1]
9.8 {1000}
[2203]
14.2 {1450}
[3192]
1/5
1/5.6
2400 [94.5]
2110 [83.1]
3775 [148.6]
1225 [48.2]
2090 [82.3]
4260 [168]
1700[66.9]
1000 [39.4]
480 [18.9]
525 [20.7]
1070 x 125 x 45
[42.1 x 4.9 x 1.8]
250 - 1090
[9.8 - 42.9]
140 [5.5]
4250 [9370]
FHG30T3
540 [106.3]
520 [102.4]
19.6 {2000}
[4400]
1/5.6
1/4.1
4260 [9390]
Truck model
Item
Performance
Max. load kg[lbs]
Basic load center mm[in.]
Lift height mm[in.]
Tilt angle (fwd-bwd) °
Free lift mm[in.] A
Lift speed mm/s[fpm]
(unloaded)
(loaded)
Traveling speed km/h[mph]
fwd 1st
2nd
rev 1st
2nd
Max. drawbar pull kN{kgf}[lbf]
(unload)
(loaded)
Gradeability
(unload)
(loaded)
Min. turning radius mm[in.] B
Min. 90° intersecting aisle mm[in.] C
Dimensions mm[in.]
Overall length D
Overall width E
Overall height
(at overhead guard) F
Overall height with
extended mast G
Wheelbase H
Tread
(front) J
(rear) K
Fork overhang L
Rear overhang M
Fork size
(Length (N) x Width (P) x Thickness (Q))
Fork spacing R
Under clearance (at frame)
Weight
Operating weight kg[lbs]
No. SEF-0F7BE
SPECIFICATIONS (3)
Truck model
Item
Performance
Max. load kg[lbs]
Basic load center mm[in.]
Lift height mm[in.]
Tilt angle (fwd-bwd) °
Free lift mm[in.] A
Lift speed mm/s[fpm]
(unloaded)
(loaded)
Traveling speed km/h[mph]
fwd 1st
2nd
rev 1st
2nd
Max. drawbar pull kN{kgf}[lbf]
(unload)
(loaded)
Gradeability
(unload)
(loaded)
Min. turning radius mm[in.] B
Min. 90° intersecting aisle mm[in.] C
Dimensions mm[in.]
Overall length D
Overall width E
Overall height
(at overhead guard) F
Overall height with
extended mast G
Wheelbase H
Tread
(front) J
(rear) K
Fork overhang L
Rear overhang M
Fork size
(Length (N) x Width (P) x Thickness (Q))
Fork spacing R
Under clearance (at frame)
Weight
Operating weight kg[lbs]
FD20T3
1810 [4000]
600 [24]
3000 [118.1]
6 - 12
160 [6.3]
670 [131.9]
630 [124.0]
18.5 [11.5]
*
18.5 [11.5]
*
8.3 {850}
[1866]
19.1 {1950}
[4300]
1/5.0
1/2.9
2170 [85.4]
1920 [75.6]
3555 [140]
1150 [45.3]
2070 [81.5]
4250 [167.3]
1600 [63.0]
970 [38.2]
970 [38.2]
450 [17.7]
435 [17.1]
1070 x 122 x 40
[42.1 x 4.8 x 1.6]
245 - 1020
[9.65 - 40.2]
110 [4.33]
3340 [7360]
FHD20T3A
640 [126.0]
620 [122.1]
26.5 {2700}
[6000]
1/2.9
FD25T3
2260 [5000]
670 [131.9]
630 [124.0]
19.1 {1950}
[4300]
1/3.5
2240 [88.2]
2010 [99.1]
3625 [142.7]
450 [17.7]
505 [19.9]
1070 x 122 x 40
[42.1 x 4.8 x 1.6]
3700 [8160]
FHD25T3A
640 [126.0]
620 [122.1]
26.5 {2700}
[6000]
1/3.5
FD30T3
2720 [6000]
135 [5.3]
590 [116.1]
520 [102.4]
19.5 [12.1]
19.5 [12.1]
9.8 {1000}
[2203]
17.2 {1750}
[3850]
1/4.8
2400 [94.5]
2110 [83.1]
3775 [148.6]
1225 [48.2]
2090 [82.3]
4260 [168]
1700 [66.9]
1000 [39.4]
480 [18.9]
525 [20.7]
1070 x 125 x 45
[42.1 x 4.9 x 1.8]
250 - 1090
[9.8 - 42.9]
140 [5.5]
4390 [9680]
FHD30T3A
540 [106.3]
520 [102.4]
23.5 {2400}
[5300]
No. SEF-0F7BE
SPECIFICATIONS (4)
Truck model
Item
Performance
Max. load kg[lbs]
Basic load center mm[in.]
Lift height mm[in.]
Tilt angle (fwd-bwd) °
Free lift mm[in.] A
Lift speed mm/s[fpm]
(unloaded)
(loaded)
Traveling speed km/h[mph]
fwd 1st
2nd
rev 1st
2nd
Max. drawbar pull kN{kgf}[lbf]
(unload)
(loaded)
Gradeability
(unload)
(loaded)
Min. turning radius mm[in.] B
Min. 90° intersecting aisle mm[in.] C
Dimensions mm[in.]
Overall length D
Overall width E
Overall height
(at overhead guard) F
Overall height with
extended mast G
Wheelbase H
Tread
(front) J
(rear) K
Fork overhang L
Rear overhang M
Fork size
(Length (N) x Width (P) x Thickness (Q))
Fork spacing R
Under clearance (at mast)
Weight
Operating weight kg[lbs]
FG35T3S
3500 [7000]
500 [24]
3000 [118.1]
6 - 12
170 [6.7]
450 [88.6]
440 [86.6]
19.5 [12.1]
*
19.5 [12.1]
*
10.8 {1100}
[2420]
18.9 {1930}
[4250]
1/6.4
1/6
2470 [97.2]
2280 [89.8]
3870 [152.4]
1290 [50.8]
2140 [84.3]
4255 [167.5]
1700 [66.9]
1060 [41.7]
970 [38.2]
495 [19.5]
605 [23.8]
1070 x 150 x 50
[42.1 x 5.9 x 2.0]
300 - 1090
[11.8 - 42.9]
145 [5.7]
4940 [10870]
FD35T3S
490 [96.5]
460 [90.6]
18.1 {1850}
[4070]
1/6
1/5.5
4820 [10605]
No. SEF-0F7BE
Unit: mm [in.]
Fig. 1 Truck Dimensions
3000 [118.1]
Free lift
No. SEF-0F7BE
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$52.99
TCM FD FHD FG FHG Series Petrol Diesel LPG Workshop Manual
Viewed 63 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$52.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
This workshop service repair manual covers the following TCM FORKLIFT models:
- FHD15 T3
- FHD18 T3
- FD20 T3
- FHD20 T3A
- FD25 T3
- FHD25 T3A
- FD30 T3
- FHD30 T3A
- FD35 T3S
- FHG15 T3
- FHG18 T3
- FG20 T3
- FHG20 T3
- FG25 T3
- FHG25 T3
- FG30 T3
- FHG30 T3
- FG35 T3S
This comprehensive workshop service manual has been designed to meet the needs of TCM technicians worldwide. It includes detailed content on various systems and components, such as:
- Engine, including fuel systems for gasoline, diesel, and LPG
- Automatic transmission system, including torque converter and transmission control valve
- Drive axle, with coverage of reduction gear and differential
- Brake system, covering brake pedal, master cylinder, wheel brake, and parking brake lever
- Steering system, including steering axle, steering wheel assembly, and power cylinder
- Hydraulic system, with detailed information on main pump, control valve, lift cylinder, and more
- Load handling, including outer and inner channels, carriage, and locations of rollers
- Electric wiring
Whether you are a professional mechanic or a DIY enthusiast, this manual provides valuable insights and guidance for maintaining and repairing TCM FORKLIFT vehicles.
