LG HLS26W Speaker Sound Bar Service Manual

P/NO : AFN74972282 APRIL, 2011 Speaker Sound Bar SERVICE MANUAL MODEL: HLS26W CAUTION BEFORE SERVICING THE UNIT, READ THE “SAFETY PRECAUTIONS” IN THIS MANUAL. Website http://biz.lgservice.com Internal Use Only MODEL: HLS26W SERVICE MANUAL

1-1 CONTENTS SECTION 1 ........ GENERAL SECTION 2 ........ CABINET & MAIN CHASSIS SECTION 3 ........ ELECTRICAL SECTION 4 ........ REPLACEMENT PARTS LIST

1-2 SECTION 1 GENERAL CONTENTS ESD PRECAUTIONS ....................................................................................................................................... 1-3 PROGRAM DOWNLOAD & UPGRADE GUIDE ........................................................................................... 1-4 SPECIFICATIONS ............................................................................................................................................ 1-5

1-3 ESD PRECAUTIONS Electrostatically Sensitive Devices (ESD) Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESD devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD devices. 6. Do not remove a replacement ESD device from its protective package until immediately before you are ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials). 7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the protective material to the chassis or circuit assembly into which the device will by installed. CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER SAFETY PRECAUTIONS. 8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ESD device). CAUTION. GRAPHIC SYMBOLS THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE LITERATURE.

1-4 PROGRAM DOWNLOAD & UPGRADE GUIDE 1. AUDIO MICOM BOOTING FUNCTION DISPLAY USB FUNCTION Insert USB “MICOM UP” DISPLAY After update, the set is turned off automatically. 2. DSP BOOTING FUNCTION DISPLAY USB FUNCTION Insert USB “DSP UP” DISPLAY After update, the set is turned off automatically. 3. MCS BOOTING FUNCTION DISPLAY USB FUNCTION Insert USB “MCS UP” DISPLAY After update, “FINISHED” DISPLAY. • FACTORY RESET: SET “STOP KEY” + REMOTE CONTROL “2” • AUDIO MICOM OPTION CODE SETTING (SERVICE INFORMATION FOR EEPROM) SET “STOP KEY” + REMOTE CONTROL “2” Change the value of Option Code with arrow key REMOTE CONTROL “STOP KEY” SET(STOP KEY) + REMOTE CONTROL “2” Complete.

1-5 SPECIFICATIONS • GENERAL Power requirements Refer to main label. Power consumption Refer to main label. Dimensions (W x H x D) (39 x 3 x 20) inches without foot Net Weight (Approx.) 5.1 lbs Operating temperature 41 °F to 95 °F (5 °C to 35 °C) Operating humidity 5 % to 90 % Bus Power Supply (USB) DC 5 V 500 mA • INPUTS DIGITAL IN (OPTICAL IN) 3 V (p-p), Optical jack x 2 PORT. IN 0.5Vrms (3.5 mm stereo jack) • AMPLIFIER Stereo mode 70 W + 70 W (4 Ω at 1 kHz)

1-6 MEMO

2-1 SECTION 2 CABINET & MAIN CHASSIS CONTENTS EXPLODED VIEWS ......................................................................................................................................... 2-3 1. RECEIVER BAR SECTION (HLS36W) .................................................................................................... 2-3 2. PACKING ACCESSORY SECTION ......................................................................................................... 2-7

2-2 MEMO

C F B G G A F D A B C D E 300 463 463 480 452 452 452 464 A42 A43 A53 465 253 255 A47 260 261 263 A46 454 454 454 256R 256L CABLE1 CABLE2 CABLE3 SMPS FRONT USB BLUETOOTH OPTION MAIN 2-4 2-3 EXPLODED VIEWS 1. RECEIVER BAR SECTION (HLS26W) NOTES) THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE LITERATURE.

You're Reading a Preview

LG HLS26W Speaker Sound Bar Service Manual

Description

Reviews

Q&A

Recently Viewed