D475A-5 00-2-1
LIST OF REVISED PAGES
(2)
The affected pages are indicated by the use of the
following marks. It is requested that necessary
actions be taken to these pages according to the
table below.
Pages having no marks are those previously revised
or made additions.
LIST OF REVISED PAGES
Mark Indication Action required
Q Page to be newly added Add
q Page to be replaced Replace
( ) Page to be deleted Discard
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
q 00-1 (2) 01-1 10-10 10-41 10-70
00-2 01-2 10-11 10-42 10-71
q 00-2-1 (2) 01-3 10-12 10-43 10-72
q 00-2-2 (2) 01-4 10-13 10-44 10-73
q 00-2-3 (2) 01-5 10-14 10-45 10-74
q 00-2-4 (2) 01-6 10-16 10-46 10-75
q 00-2-5 (2) 01-7 10-17 10-47 10-76
q 00-3 01-8 10-18 10-48 10-78
q 00-4 01-9 10-19 10-49 (1) 10-79
q 00-5 01-10 10-20 10-50 10-80
q 00-6 01-11 10-21 10-51 10-81
q 00-7 01-12 10-22 10-52 10-82
q 00-8 01-13 10-23 10-53 10-83
q 00-9 01-14 10-25 10-54 10-84
q 00-10 01-15 10-26 10-55 10-85
q 00-11 01-16 (1) 10-27 10-56 10-86
q 00-12 01-17 10-28 10-57 10-87
q 00-13 01-18 10-29 10-58 10-88
q 00-14 10-30 10-59 10-89
q 00-15 10-31 10-60 10-90
q 00-16 10-1 10-32 10-61 10-91
q 00-17 10-2 10-34 10-62 10-92
q 00-18 10-3 10-35 10-63 10-94
q 00-19 10-4 10-36 10-65 10-95
q 00-20 10-5 10-37 10-66 10-96
q 00-21 10-6 10-38 10-67 10-97
q 00-22 10-8 10-39 10-68 10-98
10-9 (1) 10-40 10-69 10-99
00-2-2 D475A-5
LIST OF REVISED PAGES
(2)
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
10-100 20-111 20-151 20-191 20-314
10-101 20-112 20-152 20-192 20-315
10-102 (1) 20-113 20-153 20-193 20-316
10-103 20-114 20-154 20-194 20-318
10-104 20-115 20-155 20-195 20-319
10-105 20-116 20-156 20-196 20-320
10-106 20-117 20-157 20-197 20-321
10-107 20-118 20-158 20-198 20-322
10-108 20-119 20-159 20-199 20-324
10-109 20-120 20-160 20-200 20-325
10-110 20-121 20-161 20-201 20-326
10-111 20-122 20-162 (1) 20-202 20-327
10-112 20-123 20-163 (1) 20-203 20-328
10-113 20-124 20-164 (1) 20-204 q 20-329 (2)
10-114 20-125 20-165 (1) 20-205 20-330
10-116 20-126 20-166 20-206 20-331
10-117 20-127 20-167 20-207 20-332
20-128 20-168 20-208 20-333
20-129 20-169 20-209 20-334
20-1 20-130 20-170 20-210 20-335
20-2 20-131 20-171 20-211 20-336
20-3 20-132 20-172 20-212 20-337
20-4 20-133 20-173 20-213 q 20-338 (2)
20-5 20-134 20-174 20-214 20-339
20-6 20-135 20-175 20-215 20-340
20-7 20-136 20-176 20-216 20-341
20-8 20-137 20-177 20-342
20-9 20-138 q 20-178 (2) q 20-301 (2) q 20-343 (2)
20-10 20-139 20-179 20-302 20-344
20-140 q 20-180 (2) 20-303 20-345
20-101 20-141 20-181 20-304 q 20-346 (2)
20-102 20-142 20-182 20-305 q 20-347 (2)
20-103 20-143 20-183 20-306 Q 20-348 (2)
20-104 20-144 20-184 20-307 Q 20-349 (2)
20-105 20-145 20-185 20-308
20-106 20-146 20-186 20-309 20-401 (1)
20-107 20-147 20-187 20-310 20-402 (1)
20-108 20-148 20-188 20-311 20-403 (1)
20-109 20-149 20-189 20-312 q 20-404 (2)
20-110 20-150 20-190 20-313 20-405
D475A-5 00-2-3
LIST OF REVISED PAGES
(2)
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
20-406 20-441-2 (1) 20-466-7 (1) 20-501 20-537
20-407 20-441-3 (1) 20-466-8 (1) 20-502 20-538
20-408 20-441-4 (1) 20-466-9 (1) 20-503 20-540
20-409 20-441-5 (1) 20-466-10 (1) 20-504 20-541
20-410 20-441-6 (1) 20-466-11 (1) 20-506 20-542
20-411 20-441-7 (1) 20-466-12 (1) 20-507 20-543
20-412 20-442 (1) 20-466-13 (1) 20-508 20-544
20-413 20-443 (1) 20-467 20-509 q 20-544-1 (2)
20-414 20-443-1 (1) 20-468 20-510 q 20-544-2 (2)
20-415 20-443-2 (1) 20-469 20-510-1 (1) q 20-544-3 (2)
20-416 20-444 (1) 20-470 20-510-2 (1) q 20-544-4 (2)
20-417 20-445 (1) 20-471 20-511 20-545
20-418 20-445-1 (1) 20-472 20-512 20-546
20-419 20-446 20-473 20-513 20-548
20-420 20-447 20-474 20-514 20-549
20-421 20-448 20-475 20-515 20-549-1 (1)
20-422 20-449 20-476 20-516 20-549-2 (1)
20-423 20-450 20-477 20-517 20-549-3 (1)
20-424 20-451 20-478 20-518 20-549-4 (1)
20-425 20-452 20-479 20-519 20-550
20-426 20-453 20-480 20-519-1 (1) 20-551
q 20-426-1 (2) 20-454 20-481 20-519-2 (1) 20-552
q 20-426-2 (2) 20-455 20-482 20-520 20-553
20-426-3 (1) 20-456 20-483 20-521 20-554
20-427 20-457 20-484 20-522 20-555
20-428 20-458 20-486 20-523 20-556
20-429 20-459 20-487 20-523-1 (1) 20-557
20-430 20-460 20-488 20-523-2 (1) 20-558
20-431 20-461 20-489 20-524 20-559
20-432 20-462 20-490 20-525 20-560
20-433 20-463 20-491 20-526 20-561
20-434 20-464 20-492 20-527 20-562
20-435 20-465 20-493 20-528 20-563
20-436 20-466 20-494 20-530 20-564
20-437 20-466-1 (1) 20-495 20-531 20-565
20-438 20-466-2 (1) 20-496 20-532 20-566
20-439 20-466-3 (1) 20-497 20-533 20-567
20-440 20-466-4 (1) 20-498 20-534 20-568
20-441 20-466-5 (1) 20-499 20-535 20-569
20-441-1 (1) 20-466-6 (1) 20-500 20-536 20-570
00-2-4 D475A-5
LIST OF REVISED PAGES
(2)
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
20-571 20-612 20-706 30-94 40-11
20-572 20-613 20-707 30-95 40-12
20-573 20-614 20-708 30-96 40-13
20-574 20-615 20-709 30-97 40-14
20-575 20-616 20-710 30-98 40-16
20-576 20-617 20-711 30-99 40-17
20-577 20-618 20-712 30-100 40-18
20-578 20-619 20-713 30-101 40-19
20-579 20-620 20-714 30-102 40-20
20-580 20-621 20-715 30-103 40-21
20-581 20-622 20-716 30-127 40-22
20-582 20-623 20-717 30-128 40-23
20-583 20-624 20-718 30-135 40-24
20-584 20-625 20-719 30-235 40-25
20-585 20-626 20-720 30-236 40-26
20-586 20-627 30-237 40-28
20-587 20-628 30-239 40-29
20-588 20-629 30-1 30-240 40-30
q 20-589 (2) 20-630 30-2 30-241 40-32
q 20-589-1 (2) 20-631 30-52 30-242 40-33
q 20-589-2 (2) 20-632 30-53 30-246 40-34
q 20-589-3 (2) 20-633 30-54 30-247 40-35
q 20-589-4 (2) 20-634 30-55 30-248 40-36
q 20-589-5 (2) 20-635 30-56 30-249 40-37
q 20-589-6 (2) 20-636 30-57 30-250 40-38
q 20-589-7 (2) 20-637 30-58 30-251 40-39
q 20-589-8 (2) 20-638 30-80 30-252 40-40
Q 20-589-9 (2) 20-639 30-81 30-253 40-41
Q 20-589-10 (2) 20-640 30-82 40-42
20-642 30-83 40-43
20-601 20-643 30-84 40-1 40-44
20-602 20-644 30-85 40-2 40-45
20-604 20-645 30-86 40-3 40-46
20-605 20-646 30-87 40-4 40-48
20-606 30-88 40-5 40-49
20-607 20-701 30-89 40-6 40-50
20-608 20-702 30-90 40-7 40-51
20-609 20-703 30-91 40-8 40-52
20-610 20-704 30-92 40-9 40-54
20-611 20-705 30-93 40-10 40-55
D475A-5 00-2-5
LIST OF REVISED PAGES
(2)
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
Mark Page
Time of
revision
90-1
90-3
90-5
90-7
90-9
90-11
90-13
90-15
90-17
90-19
90-21
90-23
SAFETY SAFETY NOTICE
00-3
SAFETY
SAFETY NOTICE
IMPORTANT SAFETY NOTICE
Proper service and repair is extremely important for safe machine operation. The service and
repair techniques recommended by Komatsu and described in this manual are both effective
and safe. Some of these techniques require the use of tools specially designed by Komatsu for
the specific purpose.
To prevent injury to workers, the symbol k is used to mark safety precautions in this manual.
The cautions accompanying these symbols should always be followed carefully. If any danger-
ous situation arises or may possibly arise, first consider safety, and take the necessary actions
to deal with the situation.
GENERAL PRECAUTIONS
Mistakes in operation are extremely dangerous.
Read the Operation and Maintenance Manual care-
fully BEFORE operating the machine.
1. Before carrying out any greasing or repairs, read
all the precautions given on the decals which are
fixed to the machine.
2. When carrying out any operation, always
wear safety shoes and helmet. Do not wear
loose work clothes, or clothes with buttons
missing.
Always wear safety glasses when hitting
parts with a hammer.
Always wear safety glasses when grinding
parts with a grinder, etc.
3. If welding repairs are needed, always have a
trained, experienced welder carry out the work.
When carrying out welding work, always wear
welding gloves, apron, hand shield, cap and
other clothes suited for welding work.
4. When carrying out any operation with two or
more workers, always agree on the operating
procedure before starting. Always inform your
fellow workers before starting any step of the
operation. Before starting work, hang UNDER
REPAIR signs on the controls in the operator's
compartment.
5. Keep all tools in good condition and learn the
correct way to use them.
6. Decide a place in the repair workshop to keep
tools and removed parts. Always keep the tools
and parts in their correct places. Always keep
the work area clean and make sure that there is
no dirt or oil on the floor. Smoke only in the areas
provided for smoking. Never smoke while work-
ing.
PREPARATIONS FOR WORK
7. Before adding oil or making any repairs, park the
machine on hard, level ground, and block the
wheels or tracks to prevent the machine from
moving.
8. Before starting work, lower blade, ripper, bucket
or any other work equipment to the ground. If
this is not possible, insert the safety pin or use
blocks to prevent the work equipment from fall-
ing. In addition, be sure to lock all the control
levers and hang warning signs on them.
9. When disassembling or assembling, support the
machine with blocks, jacks or stands before
starting work.
10.Remove all mud and oil from the steps or other
places used to get on and off the machine.
Always use the handrails, ladders or steps when
getting on or off the machine. Never jump on or
off the machine. If it is impossible to use the
handrails, ladders or steps, use a stand to pro-
vide safe footing.
SAFETY SAFETY NOTICE
00-4
PRECAUTIONS DURING WORK
11.When removing the oil filler cap, drain plug or
hydraulic pressure measuring plugs, loosen
them slowly to prevent the oil from spurting out.
Before disconnecting or removing components
of the oil, water or air circuits, first remove the
pressure completely from the circuit.
12.The water and oil in the circuits are hot when the
engine is stopped, so be careful not to get
burned.
Wait for the oil and water to cool before carry-
ing out any work on the oil or water circuits.
13.Before starting work, remove the leads from the
battery. Always remove the lead from the nega-
tive () terminal first.
14.When raising heavy components, use a hoist or
crane.
Check that the wire rope, chains and hooks are
free from damage.
Always use lifting equipment which has ample
capacity.
Install the lifting equipment at the correct places.
Use a hoist or crane and operate slowly to pre-
vent the component from hitting any other part.
Do not work with any part still raised by the hoist
or crane.
15.When removing covers which are under internal
pressure or under pressure from a spring,
always leave two bolts in position on opposite
sides. Slowly release the pressure, then slowly
loosen the bolts to remove.
16.When removing components, be careful not to
break or damage the wiring. Damaged wiring
may cause electrical fires.
17.When removing piping, stop the fuel or oil from
spilling out. If any fuel or oil drips onto the floor,
wipe it up immediately. Fuel or oil on the floor
can cause you to slip, or can even start fires.
18.As a general rule, do not use gasoline to wash
parts. In particular, use only the minimum of
gasoline when washing electrical parts.
19.Be sure to assemble all parts again in their origi-
nal places.
Replace any damaged parts with new parts.
When installing hoses and wires, be sure
that they will not be damaged by contact
with other parts when the machine is being
operated.
20.When installing high pressure hoses, make sure
that they are not twisted. Damaged tubes are
dangerous, so be extremely careful when install-
ing tubes for high pressure circuits. Also, check
that connecting parts are correctly installed.
21.When assembling or installing parts, always use
the specified tightening torques. When installing
protective parts such as guards, or parts which
vibrate violently or rotate at high speed, be par-
ticularly careful to check that they are installed
correctly.
22.When aligning two holes, never insert your fin-
gers or hand. Be careful not to get your fingers
caught in a hole.
23.When measuring hydraulic pressure, check that
the measuring tool is correctly assembled before
taking any measurements.
24.Take care when removing or installing the tracks
of track-type machines.
When removing the track, the track separates
suddenly, so never let anyone stand at either
end of the track.
FOREWORD GENERAL
00-5
FOREWORD
GENERAL
This shop manual has been prepared as an aid to improve the quality of repairs by giving the serviceman an
accurate understanding of the product and by showing him the correct way to perform repairs and make judge-
ments. Make sure you understand the contents of this manual and use it to full effect at every opportunity.
This shop manual mainly contains the necessary technical information for operations performed in a service
workshop. For ease of understanding, the manual is divided into the following chapters; these chapters are fur-
ther divided into the each main group of components.
STRUCTURE AND FUNCTION
This section explains the structure and function of each component. It serves not only to give an under-
standing of the structure, but also serves as reference material for troubleshooting.
In addition, this section may contain hydraulic circuit diagrams, electric circuit diagrams, and mainte-
nance standards.
TESTING AND ADJUSTING
This section explains checks to be made before and after performing repairs, as well as adjustments to
be made at completion of the checks and repairs.
Troubleshooting charts correlating "Problems" with "Causes" are also included in this section.
DISASSEMBLY AND ASSEMBLY
This section explains the procedures for removing, installing, disassembling and assembling each com-
ponent, as well as precautions for them.
MAINTENANCE STANDARD
This section gives the judgment standards for inspection of disassembled parts.
The contents of this section may be described in STRUCTURE AND FUNCTION.
OTHERS
This section mainly gives hydraulic circuit diagrams and electric circuit diagrams.
In addition, this section may give the specifications of attachments and options together.
NOTICE
The specifications contained in this shop manual are subject to change at any time and without any
advance notice. Use the specifications given in the book with the latest date.
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$57.99
KOMATSU D475A-3 BULLDOZER Service Repair Manual + Field ASSEMBLY Manual + Operation & Maintenance Manual
Viewed 27 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$57.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
The Komatsu D475A-3 Bulldozer Service Manual, Field Assembly Manual, and Operation & Maintenance Manual provide comprehensive information for maintaining, assembling, disassembling, and servicing this heavy equipment model. These manuals cater to both professional mechanics and DIY enthusiasts, offering step-by-step procedures for troubleshooting, repair, and maintenance.
- Covering detailed instructions on testing, adjusting, and assembling/disassembling various components,
- Specs, diagrams, and photo illustrations guide you through every service and repair procedure,
- Engine information, lubrication, and regular maintenance schedules are also included,
- Maintenance guides and troubleshooting procedures help you diagnose and resolve issues efficiently,
- Appendices provide information on safety precautions, structure and function, and periodic replacement of safety-critical parts.
This manual is suitable for anyone looking to understand the inner workings of the Komatsu D475A-3 Bulldozer and perform routine maintenance or repairs. The clear instructions and detailed diagrams make it a valuable resource for both experienced technicians and DIY enthusiasts.
