Kubota L35 Tractor and Loader Workshop Service Manual
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
SAFETY INSTRUCTIONS L3S·TL720·BT900 WSM,11640
A SAFETY FIRST
This symbol, the industry's "Safety Alert Symbol", is used throughout this manual and decals on the
machine itself to warn of the possibility of personal injury. Read these instructions carefully.
It is essential that you read the instructions and safety regulations before you attempt to repair or use
this unit.
A DANGER : Indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
A WARNING : Indicates a potentially hazardous situation which, if not avoided. could result in death
or serious injury.
A CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
• IMPORTANT : Indicates that equipment or property damage could result if instructions are not
followed.
• NOTE : Gives helpful information .
SAFETY SERVICING AND REPAIRING
(1) Before working on the machine:
• Park the machine on a firm and level ground, and set the parking brake.
• Lower the implement or mower to the ground.
• Stop the engine, and remove the key.
• Disconnect the battery's ground cable.
• Clean the work area and machine.
(2) Do not work on the machine while under the influence of alcohol, medication, or other substances or
while fatigued.
(3) Do not wear a necktie, scarf, necklace, loose or bulky clothing when you work near machine tools or
moving parts.
(4) Use tools appropriate to the work. Makeshift tools, parts, and procedures will not make good repai rs.
(5) When servicing is performed together by two or more persons, take care to perform all work safely.
(6) Do not work under the machine that is supported solely by a jack. Always support the machine by safety
stands.
L35·TL720·BT900 WSM,11640 SAFETY INSTRUCTIONS
(7) If the engine must be running to do same work, make sure the area is well ventilated. Never run the
engine in a closed area. The exhaust gas contains poisonous carbon monoxide.
(8) Do not touch the rotating or hot parts while the engine is running.
(9) Fuel is extremely flammable and explosive under certain conditions. Do not smoke or allow flames or
sparks in your working area.
(10) To avoid sparks from an accidental short circuit, always disconnect the battery's ground cable first and
connect it last.
(11) Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, clothing and cause
blindness if splashed into eyes. Keep electrolyte away from eyes, hands and clothing. If you spill
electrolyte on yourself, flush with water. and get medical attention immediately.
(12) Battery gas can explode. Keep sparks and open flame away from the top of battery, especially when
charging the battery.
(13) Never remove the radiator cap while the engine is running. or immediately after stopping. Otherwise.
hot water will spout out from radiator. Wait for more than ten minutes to cool the radiator. before
removing the cap.
(14) Escaping fluid (fuel or hydraulic oil) under pressure can penetrate the skin causing serious injury. Relieve
pressure before disconnecting hydraulic or fuel lines. Tighten all connections before applying pressure.
(15) Do not start the engine by shorting across starter terminals.
(16) Unauthorized modifications to the machine may impair the function and I or safety and affect machine
life.
(17) Do not alter or remove any part of machine safety system.
(18) Keep a first aid kit and fire extinguisher handy at all times.
(19) Be sure to chock the wheels to prevent accident during servicing the machine.
2
SAFETY
,
INSTRUCTIONS L35·TL720·BT900 WSM, 11640
SAFETY DECALS
• The following safety decals are installed on the machine.
If a decal becomes damaged, illegible or is not on the machine, replace it. The decal part number is listed
in the parts list.
A DANGER TA040-49652@
_~_Iii
o Part No. TA040-4959-2
® Part No. T A040-4956-1
Diesel fuel
B164F198
Part No. 32751-4921-1
3
L3HL720·BT900 WSM,11640 SAFETY INSTRUCTIONS
~®~P_a_rt_N_o_._3_52_6_0_~_4_9_1-_3~~~~~~~~~~~~~~~~~~@PartNo.~04~~5~1
Do not touch hot
ACAUTION
35260-34913@ surface like muffer, etc.
TO AVOID PERSONAL INJURY:
I. Read and understand the operators manual before operation.
2. Before starting the engine. make sure that everyone IS at a safe distance from the
tractor and that the PTO is OFF.
3. Do not allow passengers on the tractor at any time
4. Before ailowing other people to use the tractor. have them read the operator'5 manual.
5. Check the tightness of all ruts and bolts regularly.
6. Keep ali shields in place and stay away from all moving parts.
7 Lock the two brake pedals together before driving on the road.
B 51011. down for turns, or rough roads, or when applying individual brakes,
9. On public roads use SMV emblem ana hazard lights, if required by local traHic and
safety regulations
10 Pull only from the drawbar
I I. Berore dismounting, lower the Ifnpiement. set the parking brake, stop the engine and
remove the key.
® Part No. TA040-3015-1
~---,
i 1--\
• n)\\\\I1\\\\\l~ I
@ Part No. 32751-4958-1
Stay clear of engine fan
and fan belt.
DANGER EXPLOSIVE GASES
Cigarettes. flames or sparks could cause battery to explode. Always
shield eyes and face from battery. Do not charge or use booster cables
or adjust post connections Without prQper jr,struction and training.
KEEP VENT CAPS TIGHT AND LEVEL
POI SON CAUSES SEVERE BURNS
Contains sulfu,ic acid. Avoid contact with skin, eyes or
clothing, In event of accident flush with water and call
a physician immediately. •
KEEP OUT OF REACH OF CHILDREN 6
@ Part No. 32751-4957-1
Stay clear of engine fan and fan belt.
CARE OF DANGER, WARNING AND CAUTION LABELS
(1) Keep danger, warning and caution labels clean and free from obstructing material.
(2) Clean danger, warning and caution labels with soap and water, dry with a soft cloth.
(3) Replace damaged or missing danger, warning and caution labels with new labels from your local KUBOTA
dealer.
(4) If a component with danger, warning and caution label (s) affixed is replaced with new part, make sure new
label (s) is (are) attached in the same location (s) as the replaced component.
(5) Mount new danger, warning and caution labels by applying on a clean dry surface and pressing any bubbles to
outside edge.
B164F199
4
SPECIFICATIONS L3HL720'BT900 WSM, 11640
SPECIFICATIONS
Model L35
Maximum PTO power 19.4kW(26HP)
Engine NET power 24.2 kW (32.5 HP)
Engine
Model 01703
Type Indirect injection, Vertical, Water-Cooled, 4-cycle diesel
I Number of cylinders 3
Bore and stroke 87 x92.4 mm (3.42 x 3.63 in.)
Total displacement 1647 cm
3
(100.5 cu.in.)
Rated revolution 45 rls (2700 rpm)
Combustion chamber Spherical type (E-TVCS)
Fuel injection pump Bosh type mini pump (PFR3M)
Governor Centrifugal ball mechanical governor
Injection nozzle Throttle type
Injection timing Before T.D.C. 0.314 rad (18")
Injection order 1-2-3
Injection pressure 13.73 MPa (140 kgf/cm
2
, 1991 psi)
Compression ratio 23: 1
lubricating system Forced lubrication bytrochoidal pump
Cooling system Pressurized radiator, Forced circulation with water pum p
Starting system Electric starting with cell starter (12 V, 1.2 kW)
Alternator 12 V, 360 W (30 AMPS)
Battery 490- Cold cranking Amps at-18°C (-0.4 OF)
Fuel Diesel fuel No.1 [below -10°C (14 OF)] Diesel fuel NO.2 [above·1 0 °c (14 OF)]
lubricating oil CC or CD (API grade)
Weight (Dry) 176 kg (388Ibs)
Capacities
Fuel tank 351 (9.2 U.S.gals., 7.7Imp.gals.)
Engine crankcase 4.81 (5.1 U.S.qts., 4.2 Imp.qts.)
Engine coolant 71(7.4 U.S.qts., 6.2Imp.qts.)
Transmission case 391 (41.2 U.S.qts., 34.3lmp.qts.)
Front axle case 5.51 (5.8 U.S.qts., 4.8Imp.qts.)
Dimensions
Overall length (without 3P) 2720 mm (107.1 in.)
Overall length (with 3P) 3015 mm (118.7 in.)
Overall width (minimum tread) 1590 m m (62.6 in.)
Overall height (Top of ROPS) 2400 mm (94.5 in.)
Overall height (Top of steering
wheel)
1460 mm (77.5 in.)
Wheel base 1700 mm (66.9 in.)
5
L3HL720'BT900 WSM,11640 SPECIFICATIONS
Model
Min. ground clearance
Dimensions Front
(Std. tires)
Tread
Rear
Tire size
Front
(Std. tires)
Rear
Clutch
Traveling
Steering
system
Transmission
Traveling
Brake
Parking
Differential
Hydraulic control system
Hydraulic
system
Three point hitch
Max. lifting force (24 in. behind
lower link end)
PTOshaft
RearPTO
Revolution
Min. turning radius (with brake)
Traction system
Weight (with ROPS)
lstkm/h(mph)
2nd km/h (mph)
3rd km/h (mph)
4th km/h (mph)
Forward
5th km/h (mph)
Traveling
speed
6th km/h (mph)
7th km/h (mph)
8th km/h (mph)
1st km/h (mph)
2nd km/h (mph)
3rd km/h (mph)
4th km/h (mph)
Reverse
5th km/h (mph)
6th km/h (mph)
7th km/h (mph)
8th km/h (mph)
pumPt capacity (at rated
Front Pump 42.211 min (11.1 GPM). Power steering Pump 23.311min (6.12GPM)
revo ution engine)
L35
325 mm (12.S in.)
1165 mm (45.S6 in.)
1200 mm (47.24 in.)
27x 10.50-15
15-19.5
Dry type single stage With single plate
Hydrostatic power steering
Glide shift transmission, S for ward and S reverse speeds
Wet disc type
Connected with the traveling brake
Bevel gear
Position control
Category 1
1050 kg (2315Ibs)
SAE 1-3/S 6-splines
1 Speed 9 rls(540 rpm)/engine 37 rls(2219 rpm}
2.47 m (S.l ft)
Fixed Hitch
1450 kg (3197Ibs)
1.4(0.9)
2.0 (1.3)
3.3 (2.0)
4.9 (3.0)
6.9 (4.3)
9.7 (6.0)
15.S (9.S)
23.3 (14.5)
1.3 (O.S)
1.9 (1.1)
3.0 (1.9)
4.4 (2.S)
6.3 (3.9)
8.9 (5.5)
14.5 (9.0)
21.4 (B.3)
6
DIMENSIONS L3S·TL720·BT900 WSM, 11640
DIMENSIONS
Unit: mm (in.)
B164F058
r:::- 0
co <0
to C\i
~ ~
1.0 0 0
<0 0 OJ
(\J ~ 1.0
~
--j-------+.~
(107.09)
B164F059
7
CONTENTS
[1] FEATURES ....................................................................................................... G-1
[2] TRACTOR IDENTIFICATION ............................................................................ G-2
[3] GENERAL PRECAUTIONS ................................................................................ G-3
[4] HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING .............. G·4
[5] LUBRICANTS, FUEL AND COOLING WATER ..................................................G-8
[6] TIGHTENING TORQUES (GENERAL USE SCREWS, BOLTS AND NUTS) ........ G-9
[7] MAINTENANCE CHECK LIST ........................................................................ G-10
[8] CHECK AND MAINTENANCE ........................................................................ G-11
(1) Daily Check ............................................................................................. G·11
(2) Check Poi nts of Initial 50 Hours .............................................................. G·12
(3) Check Points of Every 50 Hours ............................................................... G-14
(4) Check Points of Every 100 Hours ............................................................. G-17
(5) Check Poi nts of Every 200 Hou rs ............................................................. G-19
(6) Check Points of Every 400 Hours ............................................................. G·20
(7) Check Poi nts of Every 800 Hours ............................................................. G·21
(8) Check Point of Every 1 Year ..................................................................... G·22
(9) Check Point of Every 2 Years ................................................................... G·22
(10) Others .................................................................................................... G-24
[9] SPECIAL TOOLS ............................................................................................ G-26
[10] TIRES ............................................................................................................ G·35
(1) Tire Pressure ........................................................................................... G-35
(2) Tread ...................................................................................................... G·35
(3) Wheel Hub ............................................................................................. G-36
(4) Tire Liquid Injection ................................................................................G-36
[11] SPECIFICATIONS OF IMPLEMENT UMITATIONS ..........................................G·39
l3Hl720'BT900 WSM, 11640 G GENERAL
[1] FEATURES
B164P029
(1) Low Noise And Vibration From The KUBOTA E-
TVCS Diesel Engine
(2) Clutchless Operation of The GST Transmission
(3) The Hard-Nose Slanted Hood And The Enclosed
Muffler
(4) The Full Flat Deck And The Hanging -Type Pedals
(5) The "One·Touch" Reversible High-Back Deluxe
Seat
(6) The Full Flat Deck And The Hanging-Type Pedals
(7) 2-Pump Hydraulic System With The Exclusive
Hydraulic Pump For Loader And Backhoe
Operations
(8) The Backhoe Quickly Attached or Detached
(9) The Powerfull Stabilizers Contribute To Stable
Backhoe Operations
(10) The Automatic self-Leveling Loader And Single
Lever Operation
(11) The 3-Pint Hitch And The PTO Fitted As
Standard Features
(12) Industrial Tire
(13) 4 Post ROPS
G-1
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$35.99
Viewed 25 Times Today
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$35.99
This workshop service manual is for the Kubota L35 Tractor and Loader. It provides comprehensive data, characteristics, instructions, and methodology for repair interventions on the vehicle and its components. The manual includes special notes, important points, service data, precautions, and detailed illustrations, exploded diagrams, drawings, and photos to guide you through every service repair procedure. It also provides adjustment and repair operations, reference to service tool numbers, and information on construction and function. The manual is intended for both professional mechanics and DIY enthusiasts and is designed primarily for use by trained technicians in a properly equipped workshop. It contains enough detail and basic information to make it useful to the owner who desires to perform basic maintenance and repair work. The manual is available in .PDF format and can be viewed on any computer, as well as zoomed and printed. Always use the correct special service tools or equipment specified and perform all work with great care and in a clean working area with adequate lighting. To maximize the life of your Kubota L35 Tractor and Loader, accurately follow the maintenance requirements, investigate unusual noises and changes in riding characteristics, use only genuine Kubota parts, follow the procedures in the manual carefully and completely, and keep complete records of all maintenance and repairs with dates and any new parts installed. The manual also contains information about adjusting work and valuable reference data for such adjustment values. All maintenance and repair work must strictly observe accident prevention guidelines. The manual is a quality, complete, and intact resource for servicing and repairing vehicles using safe, effective methods. It outlines procedures for servicing and repairing vehicles using safe, effective methods and contains many notes, cautions, and warnings which should be followed along with standard safety procedures to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.
- File Format: .PDF
- Language: English
- Printable: Yes
- Requirement: Adobe Reader
- Compatibility: Windows/ Mac and Linux OS
