2020 Toyota Hilux OEM Service & Repair Manual

Last Modified: 08-26-2024 6.11:8.1.0 Doc ID: RM100000000NCQG Model Year Start: 2016 Model: Hilux Prod Date Range: [06/2015 - ] Title: INTRODUCTION: HOW TO USE THIS MANUAL: GENERAL INFORMATION; 2016 - 2025 MY Hilux [06/2015 - ] GENERAL INFORMATION GENERAL DESCRIPTION (a) Repair operations can be separated mainly into the following 3 processes: (1) Diagnosis (2) Removing/Installing, Replacing, Disassembling/Reassembling, Checking and Adjusting (3) Final Inspection (b) The following procedures are omitted from this manual. However, these procedures must be performed. (1) Use a jack or lift to perform operations. (2) Clean all removed parts. (3) Perform a visual check before and after performing any work. INDEX (a) An alphabetical INDEX section is provided at the end of the manual as a reference to help find the item to be repaired. PREPARATION (a) Use of Special Service Tools (SST) and Special Service Materials (SSM) may be required, depending on the repair procedure. Be sure to use SST and SSM when they are required and follow the work procedure properly. A list of SST and SSM is in the "Preparation" section of this manual. REPAIR PROCEDURES (a) A component illustration is placed under the title where necessary. (b) Non-reusable parts, grease application areas, precoated parts and torque specifications are noted in the component illustrations. The following illustration is an example. SYMBOL CONTENTS Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part ★ Precoated part Apply Lubricant Here Do not apply lubricants to the threaded parts

CAUTION: "Major areas involving basic vehicle performance such as moving/turning/stopping" indicates areas that require a higher degree of precision when tightening. *A Example - - *1 CYLINDER BOOT *2 PISTON SEAL *3 FRONT DISC BRAKE PISTON *4 FRONT DISC BRAKE BLEEDER PLUG *5 FRONT DISC BRAKE BLEEDER PLUG CAP *6 SET RING *7 DISC BRAKE CYLINDER ASSEMBLY LH - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part Lithium soap base glycol grease (c) Torque specifications, grease application areas and non-reusable parts are emphasized in the procedures. HINT: There are cases where such information can only be explained by using an illustration. In these cases, torque, oil and other information are described in the illustration.

(d) Only items with key points are described in the text. What to do and other details are explained using illustrations next to the text. Both the text and illustrations are accompanied by standard values and notices. Illustration What to do and where to do it Task heading What work will be performed Explanation text How to perform the task Information such as specifications and warnings, which are written in boldface text (e) Illustrations of similar vehicle models are sometimes used. In these cases, minor details may be different from the actual vehicle. (f) Procedures are presented in a step-by-step format. SERVICE SPECIFICATIONS (a) Specifications are presented in boldface text throughout the manual. The specifications are also found in the "Specifications" section for reference. TERM DEFINITIONS CAUTION Possibility of injury to you or other people. NOTICE Possibility of damage to components being repaired. HINT Provides additional information to help you perform repairs. INTERNATIONAL SYSTEM OF UNITS (a) The units used in this manual comply with the International System of Units (SI UNIT) standard. Other units from the metric system and English system are also provided. Example: Torque: 30 N·m {306 kgf·cm, 22 ft·lbf}

Last Modified: 08-26-2024 6.11:8.1.0 Doc ID: RM100000000NCQH Model Year Start: 2016 Model: Hilux Prod Date Range: [06/2015 - 08/2017] Title: INTRODUCTION: IDENTIFICATION INFORMATION: VEHICLE IDENTIFICATION AND SERIAL NUMBERS; 2016 - 2017 MY Hilux [06/2015 - 08/2017] VEHICLE IDENTIFICATION AND SERIAL NUMBERS VEHICLE IDENTIFICATION NUMBER (a) The vehicle identification number is stamped on the vehicle body and on the certification plate as shown in the illustrations. (1) Vehicle Body (2) Certification Plate (3) Identification Number Plate ENGINE SERIAL NUMBER AND TRANSMISSION SERIAL NUMBER (a) The engine serial number is stamped on the cylinder block of the engine and the transmission serial number is stamped on the housing as shown in the illustrations.

(1) Engine Serial Number *a Engine Serial Number (2) Transmission Serial Number *a Transmission Serial Number

Last Modified: 08-26-2024 6.11:8.1.0 Doc ID: RM1000000016MIX Model Year Start: 2018 Model: Hilux Prod Date Range: [08/2017 - ] Title: INTRODUCTION: IDENTIFICATION INFORMATION: VEHICLE IDENTIFICATION AND SERIAL NUMBERS; 2018 - 2025 MY Hilux [08/2017 - ] VEHICLE IDENTIFICATION AND SERIAL NUMBERS VEHICLE IDENTIFICATION NUMBER (a) The vehicle identification number is stamped on the vehicle body and on the certification plate as shown in the illustrations. (1) Vehicle Body (2) Certification Plate (3) Identification Number Plate ENGINE SERIAL NUMBER AND TRANSMISSION SERIAL NUMBER (a) The engine serial number is stamped on the cylinder block of the engine and the transmission serial number is stamped on the housing as shown in the illustrations.

(1) Engine Serial Number *A 2TR-FE *B 1GD-FTV *a Engine Serial Number - - (2) Transmission Serial Number *A AC60F *B R151 *C RC61F - - *a Transmission Serial Number - -

Last Modified: 08-26-2024 6.11:8.1.0 Doc ID: RM100000000NCQI Model Year Start: 2016 Model: Hilux Prod Date Range: [06/2015 - 08/2017] Title: INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION; 2016 - 2017 MY Hilux [06/2015 - 08/2017] PRECAUTION BASIC REPAIR HINT (a) HINTS ON OPERATIONS 1 Attire Always wear a clean uniform. Hat and safety shoes must be worn. 2 Vehicle protection Prepare a grille cover, fender cover, seat cover and floor mat before starting the operation. 3 Safe operation Use wheel chocks to secure the vehicle. When working with the engine running, make sure to provide ventilation for exhaust fumes in the workshop. When removing or installing heavy parts, such as the engine, transmission, differential, etc., before starting work make sure there are no problems with the equipment that will be used. When working with 2 or more persons, be sure to check safety for one another. If working on high temperature, high pressure, rotating, moving, or vibrating parts, wear appropriate safety equipment and take extra care not to injure yourself or others. 4 Preparation of tools and measuring gauge Before starting any operation, prepare a tool stand, SST, necessary gauges, oil and any parts for replacement.

5 Removal, installation, disassembly and assembly operations Diagnose with a thorough understanding of proper procedures and of the reported problem. Before removing the parts, check the general condition of the assembly and for deformation and damage. When the assembly is complicated, take notes. For example, note the total number of electrical connections, bolts, or hoses removed. Add matchmarks to insure reassembly of components in the original positions. Temporarily mark hoses and their fittings if needed. Clean and wash the removed parts if necessary and assemble them after a thorough check. 6 Removed parts Place the removed parts in a separate box to avoid mixing them up with the new parts or contaminating the new parts. For non-reusable parts such as gaskets, O-rings and self-locking nuts, replace them with new ones as instructed in this manual. Retain the removed parts for customer inspection, if requested. 7* Checks to perform after work is finished Make sure that removed and installed parts (oil filler cap, level dipstick, floor mat, etc.) are properly installed/tightened. Make sure that none of the cloths or tools that were used have been left in the engine compartment or within the vehicle. Check that there are no oil leaks. CAUTION: *: Be sure to perform these checks properly. Not performing these checks properly after finishing work can lead to serious accident or injury. (b) JACKING UP AND SUPPORTING VEHICLE (1) Care must be taken when jacking up and supporting the vehicle. Be sure to lift and support the vehicle at the proper locations. (c) PRECOATED PARTS (1) Precoated parts are bolts and nuts that are coated with a seal lock adhesive at the factory. *a Seal Lock Adhesive (2) If a precoated part is retightened, loosened or moved in any way, it must be recoated with the specified adhesive. (3) When reusing a precoated part, clean off the old adhesive and dry the part with compressed air. Then apply new seal lock adhesive appropriate to that part. (4) Some seal lock agents harden slowly. You may have to wait for the seal lock adhesive to harden. (d) GASKETS (1) When necessary, use a sealer on gaskets to prevent leaks. (e) BOLTS, NUTS AND SCREWS

(1) Carefully follow all the specifications for tightening torque. Always use a torque wrench. (2) Make sure that no foreign matter (burrs, paint, etc.) gets trapped under the heads of the bolts and nuts when tightening them. (f) FUSES *a Incorrect *b Correct (1) When inspecting a fuse, check that the wire of the fuse is not broken. (2) If the wire of a fuse is broken, confirm that there are no shorts in its circuit. (3) When a fuse is replaced, a fuse with the same amperage rating must be used. ILLUSTRATION SYMBOL PART NAME ABBREVIATION FUSE FUSE CIRCUIT BREAKER CB (g) CLIPS (1) The removal and installation methods of typical clips used for vehicle body parts are shown in the table below. HINT: If a clip is damaged during a procedure, always replace the damaged clip with a new clip.

2020 Toyota Hilux OEM Service & Repair Manual

You're Reading a Preview

2020 Toyota Hilux OEM Service & Repair Manual

Engines covered:

What’s Inside the 2020 Toyota Hilux OEM Service & Repair Manual

Engine Mechanical Repair (2TR-FE & 1GD-FTV)

Engine Control System Diagnostics

Fuel System Service

Intake & Exhaust System Repair

Emission Control System Diagnostics

Cooling & Lubrication System Procedures

Starting & Charging System Service

48V System Coverage (Where Equipped)

Cruise Control System Diagnostics

Automatic Transmission (AC60F) Service

Manual Transmission (R151, RC61F) Service

Clutch & Transfer Case Service

Drive Shaft & Axle Repair

Suspension Service & Alignment

Brake System & Brake Control Diagnostics

Steering System Repair

Power Distribution & Network Diagnostics

Audio, Visual & Telematics Service

Interior Systems & HVAC Service

Exterior Body Panels & Trim

Body Repair Manual Section

OEM Wiring Diagrams & Electrical Troubleshooting

Why This Manual Works Well for Both Mechanics & DIY Owners

Format & Compatibility

Download the 2020 Toyota Hilux OEM Service & Repair Manual

Recently Viewed