AIRBAG SYSTEM
AB-2
AIRBAG SYSTEM
General Description
1. General Description
A: COMPONENT
1. SRS AIRBAG
(1) Combination switch ASSY with roll
connector
(6) Bolt (exclusive use) Tightening torque: N⋅m (kgf-m, ft-lb)
(7) Side airbag sensor T1: 7.5 (0.76, 5.5)
(2)
TORX
®
bolt T30
(8) Side airbag harness T2: 10 (1.0, 7.4)
(3) Airbag module ASSY (Driver’s
side)
(9) Side airbag module T3: 13 (1.3, 9.6)
(10) Airbag main harness T4: 25 (2.5, 18.4)
(4) Airbag module ASSY (Passen-
ger’s side)
(11) Front sub sensor harness
(12) Front sub sensor
(5) Airbag control module (13)
TORX
®
bolt T30
AB-01412
T2
T1
T4
T2
T2
(2)
(4)
(11)
(3)
(1)
(2)
(11)
(12)
(9)
(10)
(13)
(8)
(7)
(6)
(5)
T3
T1
AB-3
AIRBAG SYSTEM
General Description
B: CAUTION
• When servicing a vehicle, be sure to turn the ig-
nition switch to OFF, disconnect the ground cable
from battery, and wait for more than 20 seconds
before starting work.
• The airbag system is fitted with a backup power
source. If the airbag system is serviced within 20
seconds after the ground cable is disconnected, it
may inflate.
• If the airbag warning light illuminates, repair the
vehicle immediately. Airbag or pretensioner may in-
flate incorrectly, or not inflate in collision.
• If sensors, airbag module, airbag control module,
pretensioner, and harness are deformed or dam-
aged, replace them with new genuine parts.
• When checking the airbag system, be sure to
use a digital circuit tester.
Infinitesimal electric current in an analog circuit
tester may cause the airbag to activate erroneous-
ly.
• When checking, use a test harness (1). Do not
directly apply the tester probe to any connector ter-
minal of the airbag. Damage to the connector termi-
nal may cause the airbag to activate erroneously.
• Do not check continuity of either of the airbag
modules for driver, passenger or side, or preten-
sioner.
AB-00120
AB-00121
AB-00122
(1)
AB-00006
AB-4
AIRBAG SYSTEM
General Description
• Do not drop the airbag modulator parts, subject
them to high temperature over 93°C (199°F), or let
water, oil, or grease get on them; otherwise, the in-
ternal parts may be damaged and reliability greatly
lowered.
• If any damage, opening, or rust is found on the
airbag system wire harness, do not attempt to re-
pair using soldering equipment. Be sure to replace
the faulty harness with a new genuine part.
• Install the wire harness securely with the speci-
fied clips to avoid interference or tangled up with
other parts.
• Do not allow water or oil to come in contact with
the connector terminals. Do not touch the connec-
tor terminals.
• Either of the airbag modules for driver, passen-
ger or side, or pretensioner must not be disassem-
bled.
• The removed front seat with the airbag module
must be kept at least 200 mm (8 in) away from walls
and other objects.
• Do not use the airbag or pretensioner parts from
other vehicles. Always replace defective parts with
new parts.
• Never reuse a deployed airbag or pretensioner.
• When painting or performing sheet metal work
on the front part of the vehicle, including the front
wheel apron, front fender, and front side frame, re-
move the front sub sensors and wire harness of the
airbag system.
AB-00123
AB-00124
AB-00125
(1) More than 200 mm (8 in)
AB-00126
AB-00127
AB-00128
(1)
AB-5
AIRBAG SYSTEM
General Description
• When painting or performing sheet metal work
on the side of the vehicle, including the side sill,
center pillar, and front and rear doors, remove the
side airbag sensors and wire harness of the airbag
system.
AB-00129
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$24.99
$32.99
2006 Subaru Impreza Service & Repair Manual
Viewed 20 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$24.99
$32.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
The Subaru Impreza Workshop Manual (2006) is a comprehensive guide tailored to aid in the repair and maintenance of Subaru Impreza vehicles manufactured in 2006.
This workshop manual is an essential tool for both professional mechanics and passionate Subaru owners, providing detailed step-by-step instructions and diagrams for various repair procedures. Whether you are tackling simple maintenance tasks or complex repairs, this manual will guide you through the process.
Key features of the Subaru Impreza Workshop Manual (2006) include:
- Full coverage of all Subaru Impreza models from the year 2006
- Clear and concise instructions for various repair procedures
- Detailed diagrams and illustrations to aid in understanding
- Explanation of technical specifications, including torque settings
- Maintenance schedules and recommended service intervals
- Diagnostic charts and troubleshooting guides
- Electrical wiring diagrams
- Specifications for engine, transmission, and drivetrain components
- Exploration of the vehicle's systems, such as brakes, suspension, and steering
- Insight into the vehicle's electronics, including navigation and audio systems
- Important safety information and precautions
With the Subaru Impreza Workshop Manual (2006), you can confidently tackle repairs and maintenance tasks while ensuring the longevity and performance of your Subaru Impreza. Stay informed and empower yourself with this indispensable resource!
