2011 Renault Fluence OEM Service & Repair Manual

© Renault s.a.s 2007 "The repair procedures given by the manufacturer in this document are based on the technical specifications current when it was prepared. The procedures may be modified as a result of changes introduced by the manufacturer in the production of the various component units and accessories from which the vehicles are constructed". All rights reserved by Renault. Copying or translating, in part or in full, of this document or use of the service part reference numbering system is forbidden without the prior written authority of Renault. OCTOBER 2009 EDITION ANGLAISE X38, and B32 or L38 0 General vehicle information 01A VEHICLE MECHANICAL SPECIFICATIONS 01C VEHICLE BODYWORK SPECIFICATIONS 01D MECHANICAL INTRODUCTION 02A LIFTING EQUIPMENT 03B COLLISION 04B CONSUMABLES - PRODUCTS 04E PAINT

FLUENCE - MEGANE GENERATION - Section 0 Contents Pages FLUENCE - MEGANE GENERATION - Section 0 ContentsPages 01A VEHICLE MECHANICAL SPECIFICATIONS Vehicle: Specifications 01A-1 01C VEHICLE BODYWORK SPECIFICATIONS Vehicle panel gaps: Adjustment value 01C-1 01D MECHANICAL INTRODUCTION Tightening torques: General information 01D-1 02A LIFTING EQUIPMENT Vehicle: Towing and lifting 02A-1 03B COLLISION Vehicle involved in an impact: Impact fault finding 03B-1 04B CONSUMABLES - PRODUCTS Vehicle: Parts and consumables for the repair 04B-1 04E PAINT Anti-corrosion protection product: Description 04E-1 Colour code: Specifications 04E-5

01A- 1 VEHICLE MECHANICAL SPECIFICATIONS Vehicle: Specifications 01A Dimensions in metres: L38 144110 (A ) 0.908 (B ) 2.702 (C ) 1.010 (D ) 4.620 (E) 1.545 (F) (unladen) 1.478 (G) 1.563 (H ) 1.809

01A- 2 VEHICLE MECHANICAL SPECIFICATIONS Vehicle: Specifications 01A Dimensions in metres: B32 134816 (A ) 0.860 (B ) 2.642 (C ) 0.793 (D ) 4.294 (E) 1.546 (F) (unladen) 1.479 (G) 1.547 (H ) 1.755 Engine Gearbox Emissions standard Engine type Engine suffix Cubic capacity (cm³) Gearbox type Gearbox suffix

01A- 3 VEHICLE MECHANICAL SPECIFICATIONS Vehicle: Specifications 01A K4M 838 1598 JH3 183 EURO 3 EURO 4 839 DP0 111 EURO 3 EURO 4 K9K 830 1461 JR5 175 EURO 4 832 TL4 022 838 JR5 175 EURO 3 842 TL4 022

01C-1 VEHICLE BODYWORK SPECIFICATIONS Vehicle panel gaps: Adjustment value 01C B32 137528 No. Location Clearances (mm) (1) bonnet / front bumper 3.5 ± 1.5 (2) bonnet / headlight 2 ± 1.7 (3) bonnet / front wing 3.5 ± 1.1 (4) bonnet / front wing 3.5 ± 1.1 (5) front wing / A-pillar 4 (6) front wing / front side door 4 ± 0.8 (7) front side door / rear side door 4.5 ± 1.5 (8) front side door / rear side door 4.2 ± 1.2 (9) front side door / sill panel 4.5 ± 1.5 (10) front wing / sill panel 2.5 ± 1

01C-2 VEHICLE BODYWORK SPECIFICATIONS Vehicle panel gaps: Adjustment value 01C L38 144526 No. Location Clearances (mm) (1) bonnet / front bumper 3.5 ± 1.5 (2) bonnet / headlight 3 ± 1.9 (3) bonnet / front wing 3.5 ± 1.5 (4) bonnet / front wing 3.5 ± 1.5 (5) front wing / A-pillar 4 (6) front wing / front side door 4 ± 1 (7) front side door / rear side door 4.5 ± 1.7 (8) front side door / rear side door 4.5 ± 1.2 (9) front side door / sill panel 4.5 ± 1.5 (10) front wing / sill panel 2.5 ± 1

01C-3 VEHICLE BODYWORK SPECIFICATIONS Vehicle panel gaps: Adjustment value 01C B32 137529 No. Location Clearances (mm) (11) rear side door / rear wing 4 ± 0.8 (12) roof / tailgate 5 ± 1.5 (13) tailgate / rear wing 4.5 ± 2 (14) tailgate / rear wing 4 ± 1.7 (15) tailgate / rear screen 3 ± 1 (16) rear wing / rear light 1 ± 0.7 (17) rear bumper / rear light 1.5 ± 1 (18) tailgate / rear bumper 4 ± 2

01C-4 VEHICLE BODYWORK SPECIFICATIONS Vehicle panel gaps: Adjustment value 01C L38 144527 No. Location Clearances (mm) (11) rear side door / rear wing panel 4 ± 0.8 (12) roof / rear screen 4 ± 1.4 (13) rear screen / rear wing panel 3 ± 2 (14) boot lid / rear wing panel 1.5 ± 1.5 (15) boot lid / rear screen 4 ± 1.9 (16) rear wing panel / rear light 1.5 ± 1.5 (17) rear wing panel / fuel filler flap cover 2.5 ± 1 (18) boot lid / rear bumper 4.5 ± 1.9 (19) boot lid / rear bumper 6 ± 2.2

01D- 1 MECHANICAL INTRODUCTION Tightening torques: General information 01D I - TABLE OF STANDARD TORQUES Special notes on electrical earths The property class is indicated on the bolt (1) or (2) . II - FUNCTION OF A BOLTED ASSEMBLY The bolting system connects parts of an assembly to prevent their separation or sliding when submitted to exterior forces. Exterior forces The assembly is submitted to forces that are: - static and / or dynamic, - simple (e.g. simple traction), - multiple (traction + flexion + torsion). Fastenings Standard tightening torque (N.m) Diameter Property class M6 8.8 10 M8 8.8 25 M10 8.8 50 M10 10.9 62 M12 10.9 105 M14 10.9 180 M16 10.9 280 M18 10.9 400 Fastenings Standard tightening torque (N.m) Diameter M6 8 M8 21 M10 44 120736 120737

2011 Renault Fluence OEM Service & Repair Manual

You're Reading a Preview

Recently Viewed