2010 Pontiac Vibe Service & Repair Manual Software

2009 Pontiac Vibe - AWD | Vibe (VIN S) Service Manual | Brakes | Antilock Brake System | Specifications | Document ID: 2033874 Fastener Tightening Specifications Application Specification Metric English Brake Pipe Fitting Nuts 15 N·m 11 lb ft Brake Pressure Modulator Valve Assembly to Bracket Bolts 5.4 N·m 48 lb in Brake Pressure Modulator Valve Bracket Attaching Bolts 19 N·m 14 lb ft Brake Pressure Modulator Valve Bracket Attaching Nut 19 N·m 14 lb ft Front Wheel Speed Sensor Bolt 8.5 N·m 75 lb in Front Wheel Speed Sensor Pigtail Harness Lower Bolt 29 N·m 21 lb ft Front Wheel Speed Sensor Pigtail Harness Upper Bolt 8 N·m 71 lb in Rear Wheel Speed Sensor Bolt (AWD) 8.5 N·m 75 lb in Rear Wheel Speed Sensor Pigtail Harness Bolts (AWD) 8 N·m 71 lb in Rear Wheel Speed Sensor Pigtail Harness Nut (AWD) 5 N·m 44 lb in Rear Wheel Speed Sensor Pigtail Harness Lower Bolt (FWD) 19 N·m 14 lb ft Rear Wheel Speed Sensor Pigtail Harness Upper Bolt (FWD) 5 N·m 44 lb in © 2010 General Motors Corporation. All rights reserved. Page 1 of 1 Document ID: 2033874 4/16/2010 http://localhost:9001/si/showDoc.do?docSyskey=2033874&pubCellSyskey=940&pubObj...

2009 Pontiac Vibe - AWD | Vibe (VIN S) Service Manual | Brakes | Antilock Brake System | Repair Instructions | Document ID: 2033543 Brake Pressure Modulator Valve Replacement Removal Procedure 1. Remove the right front wheel and tire assembly. Refer to Tire and Wheel Removal and Installation . 2. Remove the right engine undercover. Refer to Engine Splash Shield Replacement - Right Side . 3. Remove the generator. Refer to Generator Replacement . 4. Remove the coolant surge tank. Refer to Radiator Surge Tank Replacement . 5. Remove the washer reservoir. Refer to Windshield Washer Solvent Container Replacement . 6. Release the electronic brake control module (EBCM) harness connector lock lever (1). 7. Disconnect the EBCM harness connector (2). © 2010 General Motors Corporation. All rights reserved. Page 1 of 7 Document ID: 2033543 4/16/2010 http://localhost:9001/si/showDoc.do?docSyskey=2033543&pubCellSyskey=1189&pubObj...

8. Mark the brake pipes (1-6) to aid in installation. 9. Remove the brake line clamp bolt (1) and clamp (2). Page 2 of 7 Document ID: 2033543 4/16/2010 http://localhost:9001/si/showDoc.do?docSyskey=2033543&pubCellSyskey=1189&pubObj...

10. Remove the brake pipes (1-6) from the brake modulator assembly. 11. Plug the brake pipes in order to prevent loss or contamination of brake fluid. 12. Remove the 2 bolts (2) from the brake pressure modulator bracket (3). 13. Remove the nut (1) and the brake pressure modulator assembly and bracket. Page 3 of 7 Document ID: 2033543 4/16/2010 http://localhost:9001/si/showDoc.do?docSyskey=2033543&pubCellSyskey=1189&pubObj...

14. Remove the 3 bolts and the brake pressure modulator assembly from the bracket. Installation Procedure Caution: Refer to Fastener Caution in the Preface section. 1. Install the brake pressure modulator assembly to the bracket. Secure with the 3 bolts. Tighten Tighten the brake modulator assembly nuts to 5 N·m (48 lb in). Page 4 of 7 Document ID: 2033543 4/16/2010 http://localhost:9001/si/showDoc.do?docSyskey=2033543&pubCellSyskey=1189&pubObj...

You're Reading a Preview

2010 Pontiac Vibe Service & Repair Manual Software

Description

Reviews

Q&A

Recently Viewed