2016 Nissan Murano Service & Repair Manual

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the SR and SB section of this Service Manual. WARNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer. Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section. Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS WARNING: When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery or batteries, and wait at least three minutes before performing any service.

Precaution for Procedure without Cowl Top Cover When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc. to prevent damage to windshield. NIS0000000012919792-01-PIIB3706J

Precaution for Brake System WARNING: Clean any dust from the front brake and rear brake using a vacuum dust collector. Do not blow by compressed air. Brake fluid use refer to Fluids and Lubricants . Do not reuse drained brake fluid. Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface. Always clean with new brake fluid when cleaning the master cylinder, brake caliper and other components. Do not use mineral oils such as gasoline or light oil to clean. They may damage rubber parts and cause improper operation. Always loosen the brake tube flare nut with a flare nut wrench. Tighten the brake tube flare nut to the specified torque with crowfoot (A) and torque wrench (B). NIS0000000012919793-01-JPFIA0001ZZ Always confirm the specified tightening torque when installing the brake pipes. Turn the ignition switch OFF and disconnect the ABS actuator and electric unit (control unit) connector or the battery negative terminal before performing the work. Always connect the battery terminal when moving the vehicle. Check that no brake fluid leakage is present after replacing the parts. Check for bends, cracks and damage to the brake pedal. Adjust brake pedal if it is outside the standard value. Burnish the brake contact surfaces after refinishing or replacing rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Front brake: refer to Inspection and Adjustment. Rear brake: refer to Inspection and Adjustment.

Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-46532) Brake height tool NIS0000000012919794-01- LFIA0227E Measuring brake pedal height 38-PFM92 ( — ) ProCut™PFM Series Lathe NIS0000000012919794-02- ALFIA0092ZZ Refinishing rotors

Commercial Service Tool Tool name Description 1. Flare nut crowfoot 2. Torque wrench NIS0000000012919795-01-S-NT360 Tightening brake tube flare nuts a: 10 mm (0.39 in)/12 mm (0.47 in) Power tool NIS0000000012919795-02- PIIB1407E Loosening nuts, screws and bolts

Inspection INSPECTION Uneven Wear Check the uneven wear of the disc brake rotor using a micrometer. Replace the disc brake rotor if the thickness is below the wear limit. NIS0000000014453881-01-SBR020B Thickness variation (measured at 8 positions) : Refer to Rear Disc Brake.

Inspection INSPECTION Uneven Wear Check the uneven wear of the disc brake rotor using a micrometer. Replace the disc brake rotor if the thickness is below the wear limit. NIS0000000014453880-01-SBR020B Thickness variation (measured at 8 positions) : Refer to Front Disc Brake.

Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts. Reference page Inspection and Adjustment, Inspection and Adjustment Inspection, Inspection, Inspection and Adjustment, Inspection and Adjustment Inspection, Inspection, Inspection and Adjustment, Inspection and Adjustment Inspection and Adjustment, Inspection and Adjustment Inspection, Inspection Inspection, Inspection Inspection, Inspection Inspection, Inspection, Inspection and Adjustment, Inspection and Adjustment NVH Troubleshooting Chart (AWD) NVH Troubleshooting Chart (AWD) NVH Troublesho Chart NVH Troublesho Chart Possible cause and SUSPECTED PARTS Brake pad - damaged Brake pad - uneven wear Shims damaged Disc brake rotor imbalance Disc brake rotor damage Disc brake rotor runout Disc brake rotor deformation Disc brake rotor deflection Disc brake rotor rust Disc brake rotor thickness variation PROPELLER SHAFT DIFFERENTIAL AXLE Symptom BRAKE Noise × × × × × × Shake × × × Shimmy, Shudder × × × × × × × × ×: Applicable

Inspection BRAKE FLUID LEVEL Make sure that the brake fluid level in the sub tank is between the MAX and MIN lines. NIS0000000012919798-01-ALFIA0249ZZ Visually check around the sub tank and reservoir tank for brake fluid leakage. If the brake fluid level is excessively low, check the brake system for leakage. If brake warning lamp remains illuminated after parking brake pedal is released, check the brake system for brake fluid leakage. BRAKE LINE 1 Check brake line (tubes and hoses) for cracks, deterioration or other damage. Replace any damaged parts. 2 Check for brake fluid leakage by fully depressing brake pedal while engine is running. NIS0000000012919798-02-SBR389C CAUTION: If brake fluid leakage occurs around joints, retighten or replace damaged parts as necessary.

Drain and Refill CAUTION: Do not spill or splash brake fluid on painted surfaces. Brake fluid may damage paint. If brake fluid is splashed on painted areas, wash it away with water immediately. Prior to repair, turn the ignition switch OFF, disconnect the harness connector from the ABS actuator and electric unit (control unit) or negative battery terminal. Refer to Battery Disconnect. Refill brake system with new brake fluid. Refer to Fluids and Lubricants. Do not reuse drained brake fluid. DRAINING 1 Turn ignition switch OFF and disconnect the harness connector from the ABS actuator and electric unit (control unit) or negative battery terminal. Refer to Battery Disconnect. 2 Connect a vinyl tube to bleeder valve. NIS0000000012919806-01-BRA0007D 3 Depress brake pedal, loosen bleeder valve, and gradually remove brake fluid. CAUTION: Do not allow reservoir tank to empty as this may cause damage to master cylinder internal components. REFILLING 1 Make sure no foreign material is in the reservoir tank or sub tank, and refill with new brake fluid. NIS0000000012919806-02-PFIA0403J CAUTION: Do not reuse drained brake fluid.

2016 Nissan Murano Service & Repair Manual

You're Reading a Preview

Recently Viewed