2008 ENGINE
Engine Overhaul (2.4L) - Outlander
GENERAL SPECIFICATIONS
GENERAL SPECIFICATIONS
SERVICE SPECIFICATIONS
SERVICE SPECIFICATIONS
Item Specifications
Engine model 4B12
Type In-line OHV, DOHC
Number of cylinders 4
Combustion chamber Pentroof type
Total displacement cm
3
(cu in)
2,359 (144.0)
Cylinder bore mm 88
Piston stroke mm 97
Compression ratio 10.5
Valve timing Intake valve Open 0-40°
Close 64-24°
Exhaust valve Open 44-24°
Close 0-20°
Auto lash adjuster Non-equipped
Item Standard value Limit
Timing chain
Valve clearance mm (in) Intake 0.20 ± 0.03 (0.008 ±
0.001)
-
Exhaust 0.30 ± 0.03 (0.012 ±
0.001)
-
Camshaft
Cam height of camshaft
mm (in)
Intake 44.1 (1.736) 43.6 (1.717)
Exhaust 45.0 (1.772) 44.5 (1.752)
Cylinder head and valves
Distortion of cylinder head bottom mm (in) Within 0.05 (0.002) 0.02 (0.0008)
Grinding limit of cylinder head bottom mm (in) - 0.2 (0.008)
Overall height of cylinder head mm (in) 128.5 (5.06) -
Overall length of valve
mm (in)
Intake 113.18 (4.456) 112.68 (4.436)
Exhaust 105.89 (4.169) 105.39 (4.149)
Valve margin mm (in) Intake 1.022 (0.0402) 0.522 (0.0206)
2008 Mitsubishi Outlander XLS
2008 ENGINE Engine Overhaul (2.4L) - Outlander
2008 Mitsubishi Outlander XLS
2008 ENGINE Engine Overhaul (2.4L) - Outlander
REWORK DIMENSIONS
REWORK DIMENSIONS
Exhaust 1.094 (0.0431) 0.594 (0.0234)
Free height of valve spring mm (in) 47.44 (1.867) -
Squareness of valve spring 2° or less 4°
Clearance between valve
guide and valve stem mm
(in)
Intake 0.020-0.047 (0.0008-
0.0019)
0.10 (0.0039)
Exhaust 0.030-0.054 (0.0012-
0.0021)
0.11 (0.0043)
Valve seat contact width
mm (in)
Intake 1.16-1.46 (0.046-0.058) -
Exhaust 1.35-1.65 (0.053-0.065) -
Press fit the valve guide mm (in) 14.6-15.2 (0.57-0.60) -
Piston and connecting rod
Piston pin press-fit load N (lbf) 7,500-17,500 (1.686-
3.934)
-
Clearance between piston
ring and ring groove mm
(in)
Number 1 0.03-0.07 (0.001-0.003) 0.1 (0.004)
Number 2 0.03-0.07 (0.001-0.003) 0.1 (0.004)
Piston ring end gap mm
(in)
Number 1 0.15-0.25 (0.006-0.011) 0.8 (0.03)
Number 2 0.25-0.40 (0.010-0.016) 0.8 (0.03)
Oil 0.10-0.35 (0.004-0.014) 1.0 (0.04)
Clearance of connecting rod big end thrust mm (in) 0.10-0.25 (0.004-0.010) 0.4 (0.016)
Difference of outside diameter of connecting rod
bolt mm (in)
- 0.1 (0.04)
Connecting rod bearing oil clearance mm (in) 0.018-0.045 (0.0007-
0.0018)
0.1 (0.04)
Crankshaft and cylinder block
Underhead length of crankshaft bearing cap bolt
mm (in)
75.5-76.5 (2.972-3.012) -
Crankshaft end play mm (in) 0.05-0.25 (0.002-0.010) 0.4 (0.016)
Crankshaft journal oil clearance mm (in) 0.012-0.030 (0.0005-
0.0012)
0.08 (0.0031)
Distortion of cylinder block top surface mm (in) - 0.05 (0.0020)
Grinding limit of cylinder block top surface mm (in) - 0.2 (0.008)
Cylinder block cylinder bore mm (in) 88 (3.46) -
Cylindricity of cylinder block mm (in) 0.0076 (0.0003) -
Item Standard value
Cylinder head and valve
Cylinder head oversize valve seat bore diameter mm
Intake
0.30 Over
size
36.22-36.24 (1.426-
1.427)
2008 Mitsubishi Outlander XLS
2008 ENGINE Engine Overhaul (2.4L) - Outlander
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
(in)
Exhaust
0.30 Over
size
30.22-30.24 (1.190-
1.191)
Cylinder head oversize valve guide bore diameter mm (in)
0.25 Over
size
11.23-11.25 (0.442-
0.443)
Item Specification
Generator and ignition system
Idler pulley bolt 48 ± 7 N.m (36 ± 4 ft-lb)
Auto tensioner bolt 22 ± 4 N.m (17 ± 2 ft-lb)
Crankshaft pulley center bolt 210 N.m (155 ft-lb)
Generator nut 44 ± 10 N.m (32 ± 7 ft-lb)
Generator bolt 44 ± 10 N.m (32 ± 7 ft-lb)
Ignition coil bolt 10 ± 2 N.m (89 ± 17 in-lb)
Spark plug 25 ± 5 N.m (19 ± 3 ft-lb)
Power steering pump bracket bolt (M8) 23 ± 2 N.m (17 ± 1 ft-lb)
Power steering pump bracket bolt (M10) 44 ± 8 N.m (33 ± 5 ft-lb)
Throttle body and EGR system
Vacuum pipe and hose bolt (M6) 11 ± 1 N.m (98 ± 8 in-lb)
Vacuum pipe and hose bolt (M8) 24 ± 3 N.m (18 ± 1 ft-lb)
Water pipe bolt 10 ± 2 N.m (89 ± 17 in-lb)
Throttle body bolt 9.5 ± 2.5 N.m (84 ± 22 in-lb)
Throttle body stay bolt 20 ± 2 N.m (15 ± 1 ft-lb)
EGR valve support bolt 20 ± 2 N.m (15 ± 1 ft-lb)
EGR pipe bolt 20 ± 2 N.m (15 ± 1 ft-lb)
EGR support stay A bolt 20 ± 2 N.m (15 ± 1 ft-lb)
EGR support stay B bolt 20 ± 2 N.m (15 ± 1 ft-lb)
EGR valve bolt 24 ± 3 N.m (18 ± 1 ft-lb)
Manifold absolute pressure (MAP) sensor screw 4.0 ± 1.0 N.m (36 ± 8 in-lb)
Solenoid valve screw 4.0 ± 1.0 N.m (36 ± 8 in-lb)
Intake manifold and fuel system
Oil dipstick guide bolt 10 ± 2 N.m (89 ± 17 in-lb)
Injector protector rear bolt 20 ± 2 N.m (15 ± 1 ft-lb)
Fuel rail bolt 20 ± 2 N.m (15 ± 1 ft-lb)
Intake manifold bolt and nut 3.5 ± 1.5 N.m (31 ± 13 in-lb) --> 20 ± 2 N.m (15 ± 1
ft-lb)
Intake manifold stay bolt 20 ± 2 N.m (15 ± 1 ft-lb)
Injector protector front bolt 20 ± 2 N.m (15 ± 1 ft-lb)
Generator bracket bolt 44 ± 8 N.m (33 ± 5 ft-lb)
2008 Mitsubishi Outlander XLS
2008 ENGINE Engine Overhaul (2.4L) - Outlander
Detonation sensor bolt 20 ± 2 N.m (15 ± 1 ft-lb)
Engine oil pressure switch 10 ± 2 N.m (89 ± 17 in-lb)
Exhaust manifold
Exhaust manifold upper cover bolt 14 ± 1 N.m (124 ± 8 in-lb)
Exhaust manifold lower cover bolt 14 ± 1 N.m (124 ± 8 in-lb)
Exhaust manifold nut 49 ± 5 N.m (36 ± 3 ft-lb)
Exhaust manifold bracket C bolt (M8) 20 ± 5 N.m (15 ± 3 ft-lb)
Exhaust manifold bracket A bolt (M10) 41 ± 10 N.m (30 ± 7 ft-lb)
Crankshaft position sensor bolt 11 ± 1 N.m (98 ± 8 in-lb)
Crankshaft position sensor cover bolt (M6) 11 ± 1 N.m (98 ± 8 in-lb)
Crankshaft position sensor cover bolt (M10) 49 ± 6 N.m (36 ± 4 ft-lb)
Water hose and pipe
Water inlet fitting bolt 24 ± 3 N.m (18 ± 1 ft-lb)
Water outlet fitting bolt 24 ± 3 N.m (18 ± 1 ft-lb)
Thermostat housing bolt 24 ± 3 N.m (18 ± 1 ft-lb)
Engine hanger bolt 24 ± 3 N.m (18 ± 1 ft-lb)
Engine coolant temperature sensor 30 ± 9 N.m (22 ± 6 ft-lb)
Water pump bolt 24 ± 3 N.m (18 ± 1 ft-lb)
Water pipe nut 24 ± 3 N.m (18 ± 1 ft-lb)
Camshaft position sensor bolt 11 ± 1 N.m (98 ± 8 in-lb)
Oil pan and timing chain case
Cylinder head cover bolt 3.0 ± 1.0 N.m (27 ± 8 in-lb) --> 5.5 ± 0.5 N.m (49 ±
8 in-lb)
Timing chain case bolt (M6) 10 ± 2 N.m (89 ± 17 in-lb)
Timing chain case bolt (M8 x 10) 13 ± 1 N.m (115 ± 8 in-lb)
Timing chain case bolt (M8 x 28) 24 ± 4 N.m (18 ± 1 ft-lb)
Oil pan bolt (M6) 10 ± 2 N.m (89 ± 17 in-lb)
Oil pan bolt (M8) 29 ± 2 N.m (21 ± 1 ft-lb)
Air compressor bracket bolt 23 ± 6 N.m (17 ± 4 ft-lb)
Oil drain plug 39 ± 5 N.m (29 ± 3 ft-lb)
Oil filter 14 ± 2 N.m (124 ± 17 in-lb)
Positive Crankcase Ventilation Valve 2.5 ± 0.4 N.m (22 ± 3 in-lb)
Engine support bracket bolt 45 ± 5 N.m (33 ± 3 ft-lb)
Timing chain
Chain upper guide bolt 10 ± 2 N.m (89 ± 17 in-lb)
Oil jet bolt 10 ± 2 N.m (89 ± 17 in-lb)
V.V.T. intake sprocket bolt 59 ± 5 N.m (44 ± 3 ft-lb)
V.V.T. exhaust sprocket bolt 59 ± 5 N.m (44 ± 3 ft-lb)
Timing chain tensioner bolt 10 ± 2 N.m (89 ± 17 in-lb)
Tensioner lever bolt 10 ± 2 N.m (89 ± 17 in-lb)
Timing chain guide bolt 10 ± 2 N.m (89 ± 17 in-lb)
2008 Mitsubishi Outlander XLS
2008 ENGINE Engine Overhaul (2.4L) - Outlander
NEW TIGHTENING METHOD BY USING PLASTIC REGION TIGHTENING BOLT
Plastic region tightening bolts are used in some parts of the engine. Install these bolts according to the method
described in the body of the manual because the tightening method of these bolts are different from the
conventional method. The service limit is determined for these bolts. Be sure to strictly follow the service limit
described in the body of the manual.
Parts to be used
1. Cylinder head bolt
2. Bearing cap bolt
3. Connecting rod cap bolt
Tightening method
After tightening to the specified tightening torque, further tighten 90° and 90°, or 180° (90° + 90°).
Follow the tightening method described in the body of the manual because the tightening method differs
from part to part.
SEALANTS
SEALANTS REFERENCE
Camshaft
Engine oil control valve (OCV) bolt 10 ± 2 N.m (89 ± 17 in-lb)
Camshaft bearing cap bolt (M6) 12 ± 1 N.m (107 ± 8 in-lb)
Front camshaft bearing cap bolt (M8) 17 ± 3 N.m (14 ± 2 ft-lb) --> 30 ± 2 N.m (22 ± 1 ft-
lb)
Cylinder head and valves
Cylinder head bolt 35 ± 2 N.m (26 ± 1 ft-lb) --> +180°
Balancer chain
Drive plate bolt 40 N.m (30 ft-lb) --> 130 N.m (95 ft-lb)
Balancer shaft module bolt 20 (15 ft-lb) --> 44 (32 ft-lb) --> 0 --> 20 (15 ft-lb) -
-> +135°
Balancer shaft chain tensioner bolt 10 ± 2 N.m (89 ± 17 in-lb)
Lever tensioner bolt 10 ± 2 N.m (89 ± 17 in-lb)
Balancer shaft chain guide bolt 10 ± 2 N.m (89 ± 17 in-lb)
Ladder frame bolt 26 ± 1 N.m (19 ± 1 ft-lb)
Piston and connecting rod
Connecting rod cap bolt 5.0 N.m (44 in-lb) --> 20 N.m (15 ft-lb) --> +90°
Crankshaft and cylinder block
Crankshaft sensing ring bolt 11 N.m (98 in-lb)
Bearing cap bolt 26.5 ± 2.0 N.m (20 ± 1 ft-lb) --> +45°
Points of application Specified sealant/adhesive
2008 Mitsubishi Outlander XLS
2008 ENGINE Engine Overhaul (2.4L) - Outlander
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$31.99
2003-2008 Mitsubishi Outlander Service & Repair Manual
Viewed 55 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$31.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
This is the complete official full factory service repair manual for the Mitsubishi Outlander 2003-2008.
This service manual has easy-to-read text sections with top quality diagrams and instructions. It is specifically written for the do-it-yourselfer as well as the experienced mechanic. With step by step instruction & highly detailed exploded pictures & diagrams to show you how to complete the required job correctly & efficiently. Using Mitsubishi Outlander 2003-2008 Service Repair Workshop Manual covers every single detail on your machine. Provides step-by-step instructions based on the complete disassembly of the machine.
This Mitsubishi Outlander 2003-2008 repair manual is an inexpensive way to keep your vehicle working properly.
Models Covers:
- Mitsubishi Outlander 2003-2008
This professional technical manual contains service, maintenance, and troubleshooting information for your Mitsubishi Outlander 2003-2008, covering all models/engines/trim/transmissions types. This top quality Mitsubishi Outlander 2003-2008 Workshop Repair Service manual is complete and intact as should be without any missing/corrupt part or pages. It is the same manual used in the local service/repair shop. Mitsubishi Outlander 2003-2008 manual is guaranteed to be fully functional to save your precious time.
Immediate access! No waiting! You will have instant access to your manual! No shipping fee, no waiting nervously for the postal delivery, you can start doing your repairs right away!
Product Details:
- Mitsubishi Outlander 2003-2008
- File Format: PDF
- Language: English
- Printable: Without any restriction
- Delivery: Link will appear on the checkout page after payment is complete.
- Requirements: Adobe Reader
Buyers can pay for products via PayPal or Credit Card. We accept payments on behalf of our merchants and send payouts once per week. Click on the instant payment button to pay with your PayPal or credit card and you will receive the link instantly.
