2011 JEEP COMPASS MK Service and Repair Manual

2007 Jeep COMPASS Submodel: LIMITED | Engine Type: L4 | Liters: 2.4 Fuel Delivery: FI | Fuel: GAS DESCRIPTION Click to enlarge To protect the A/C compressor from any liquid slugging, an A/C accumulator (1) is used in this A/C system to retain any refrigerant that may exit from the evaporator in a liquid state. The A/C accumulator is mounted below the engine compartment behind the right side of the front fascia. A band and mounting bracket (2) secures the A/C accumulator to the right front frame rail and t he connections are sealed by use of metal gaskets (3) and rubber O-rings (4). OPERATION Click to enlarge Typical A/C accumulator shown. Refrigerant enters the A/C accumulator (1) mostly as a low pressure vapor through the inlet tube (2). Any liquid, oil-laden refrigerant falls to the bottom of the canister, which acts as a separator. A desiccant bag (3) is mounted inside the accumulator canister to absorb any moisture which may have entered and become trapped within the refrigerant system. A filter (4) is also mounted inside the canister to trap any foreign material that may have entered the refrigerant system during assembly. The low pressure vapor exits the A/C accumulator through the outlet tube (5). Replacement of the refrigerant line O-ring seals and gaskets is required anytime a refrigerant line is opened. Failure to replace the rubber O-ring seals and metal gaskets could result in a refrigerant system leak. The A/C accumulator has no serviceable parts except for the O-ring seals and gaskets. The O-ring seals used on the connections are made from a special type of rubber not affected by R- 134a refrigerant. The O-ring seals and gaskets must be replaced whenever the A/C accumulator is removed and installed. The A/C accumulator cannot be repaired and must be replaced if found to be leaking or damaged, or if an internal failure of the A/C compressor has occurred.

2007 Jeep COMPASS Submodel: LIMITED | Engine Type: L4 | Liters: 2.4 Fuel Delivery: FI | Fuel: GAS REMOVAL Warning: Review safety precautions and warnings in this group before performing this procedure (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - WARNING) and (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - CAUTION). Failure to follow the warnings and cautions could result in possible personal injury or death. Click to enlarge 1. Disconnect and isolate the negative battery cable. 2. Recover the refrigerant from the refrigerant system (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - STANDARD PROCEDURE - REFRIGERANT SYSTEM RECOVERY). 3. Raise and support the vehicle. 4. Remove the right front wheel (refer to 22 - TIRES/WHEELS - REMOVAL). 5. Remove the three push-pin retainers (1) and three screws (2) that secure the front portion of the right front wheelhouse splash shield (3) to body (4) and position the front of the wheelhouse splash shield out of the way to gain access to the A/C accumulator. Click to enlarge 1. Remove the nut (7) that secures the lower A/C suction line (8) to the accumulator outlet tube (9) and disconnect the suction line from the accumulator tube. 2. Remove the bolt (5) and retaining band (6) that secure the A/C accumulator to the mounting bracket (10). 3. Remove the nut (3) that secures the upper A/C suction line (2) to the accumulator inlet tube (4) and disconnect the suction line from the accumulator tube. 4. If necessary remove the accumulator mounting bracket from the body. 5. Remove and discard the O-ring seals and gaskets and install plugs in, or tape over the opened refrigerant line fittings and the accumulator ports.

INSTALLATION Caution: Be certain to adjust the refrigerant oil level when servicing the A/C refrigerant system (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING/REFRIGERANT OIL - STANDARD PROCEDURE - REFRIGERANT OIL LEVEL). Failure to properly adjust the refrigerant oil level will prevent the A/C system from operating as designed and can cause serious A/C compressor damage. Caution: The A/C accumulator must be replaced if an internal failure of the A/C compressor has occurred. Failure to replace the A/C accumulator can cause serious A/C compressor damage. When replacing multiple A/C system components, refer to the Refrigerant Oil Capacities chart to determine how much oil should be added to the refrigerant system (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING/REFRIGERANT OIL - STANDARD PROCEDURE - REFRIGERANT OIL LEVEL). If only the A/C accumulator is being replaced, add 30 milliliters (1.0 fluid ounce) of refrigerant oil to the refrigerant system. Use only refrigerant oil of the type recommended for the A/C compressor in the vehicle. Replacement of the refrigerant line O-ring seals and gaskets is required anytime a refrigerant line is opened. Failure to replace the rubber O-ring seals and metal gaskets could result in a refrigerant system leak. Click to enlarge 1. If removed, install the accumulator mounting bracket (10). Tighten the retaining bolts to 15 N·m (11 ft. lbs.). 2. Remove the tape or plugs from all of the opened refrigerant line fittings and the accumulator ports. 3. Lubricate new rubber O-ring seals with clean refrigerant oil and install them and new gaskets onto the suction line and accumulator fittings. Use only the specified O- rings as they are made of a special material for the R-134a system. Use only refrigerant oil of the type recommended for the A/C compressor in the vehicle. 4. Connect the upper A/C suction line (2) to the accumulator inlet tube (4) and install the retaining nut (3). Tighten the nut to 5 N·m (44 in. lbs.). 5. Install the retaining band (6) and bolt (5) that secure the A/C accumulator (1) to the mounting bracket. Tighten the bolt to 8 N·m (71 in. lbs.). 6. Connect the lower A/C suction line (8) to the accumulator outlet tube (9) and install the retaining nut (7). Tighten the nut to 5 N·m (44 in. lbs.). Click to enlarge 1. Reposition the front of the right front wheel house splash shield (3) to the body (4) and install the three push-pin retainers (1) and the three screws (2). Tighten the screws securely. 2. Install the right front wheel (refer to 22 - TIRES/WHEELS - INSTALLATION). 3. Lower the vehicle. 4. Reconnect the negative battery cable.

Caution: Do NOT run the engine with a vacuum pump in operation or with a vacuum present within the A/C system. Failure to follow this caution will result in serious A/C compressor damage. 1. Evacuate the refrigerant system (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - STANDARD PROCEDURE - REFRIGERANT SYSTEM EVACUATE). 2. If the A/C accumulator is being replaced, add 30 milliliters (1.0 fluid ounce) of refrigerant oil to the refrigerant system. When replacing multiple A/C system components, refer to the Refrigerant Oil Capacities chart to determine how much oil should be added to the refrigerant system (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING/REFRIGERANT OIL - STANDARD PROCEDURE - REFRIGERANT OIL LEVEL). Use only refrigerant oil of the type recommended for the A/C compressor in the vehicle. 3. Charge the refrigerant system (refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - STANDARD PROCEDURE - REFRIGERANT SYSTEM CHARGE).

2007 Jeep COMPASS Submodel: LIMITED | Engine Type: L4 | Liters: 2.4 Fuel Delivery: FI | Fuel: GAS DESCRIPTION Click to enlarge The recirculation door actuator (1) is a reversible, 12 volt direct current (DC) servo motor, which is connected directly to the pivot shaft lever of the recirculation-air door. The recirculation door actuator is located on the right side of the HVAC air inlet housing. The recirculation door actuator is contained within a black molded plastic housing with an integral wire connector receptacle (2), an output shaft with splines (3) that connect it to the recirculation door and three integral mounting tabs (4) that allow the actuator to be secured to the air inlet housing. The recirculation door actuator does not require mechanical indexing to the recirculation-air door, as it is electronically calibrated by the A/C-heater control. OPERATION The recirculation door actuator is connected to the A/C-heater control through the vehicle electrical system by a dedicated two-wire lead and connector of the instrument panel wire harness. The recirculation door actuator can move the recirculation-air door in two directions. When the A/C-heater control pulls the voltage on one side of the motor connection high and the other connection low, the recirculation-air door will move in one direction. When the A/C-heater control reverses the polarity of the voltage to the motor, the recirculation-air door moves in the opposite direction. Once the A/C-heater control makes the voltage to both connections high or both connections low, the recirculation-air door stops and will not move. The A/C-heater control uses a pulse-count positioning system to monitor the operation and relative position of the recirculation door actuator and the recirculation-air door. The A/C-heater control learns the recirculation-air door stop positions during the calibration procedure and will store a diagnostic trouble code (DTC) for any problems it detects in the recirculation door actuator circuits ( refer to 24 - HVAC Electrical Diagnostics for more information). The recirculation door actuator cannot be adjusted or repaired and it must be replaced if found inoperative or damaged.

2007 Jeep COMPASS Submodel: LIMITED | Engine Type: L4 | Liters: 2.4 Fuel Delivery: FI | Fuel: GAS REMOVAL Warning: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death. Illustration shown with instrument panel removed for clarity. Click to enlarge LHD model shown. RHD model similar. 1. Disconnect and isolate the negative battery cable. 2. Remove the glove box bin (refer to 23 - BODY/INSTRUMENT PANEL/BIN-GLOVE BOX - REMOVAL). 3. Reach through the glove box opening in the instrument panel and remove the screws (1) that secure the recirculation door actuator (2) to the right side of the HVAC air inlet housing (3). 4. Disconnect the wire harness connector (4) from the recirculation door actuator and remove the actuator. INSTALLATION Illustrations shown with instrument panel removed for clarity. Click to enlarge LHD model shown. RHD model similar. 1. Position the recirculation door actuator (1) to the right side of the HVAC air inlet housing (2). 2. Install the recirculation door actuator onto the air inlet housing. If necessary, rotate the actuator slightly to align the splines on the actuator output shaft (3) with those on the

recirculation door pivot shaft adapter (4). Click to enlarge 1. Install the screws (1) that secure the recirculation door actuator (2) to the air inlet housing (3). Tighten the screws to 2 N·m (17 in. lbs.). 2. Connect the instrument panel wire harness connector (4) to the recirculation door actuator. 3. Install the glove box bin (refer to 23 - BODY/INSTRUMENT PANEL/BIN-GLOVE BOX - INSTALLATION). 4. Reconnect the negative battery cable.

2007 Jeep COMPASS Submodel: LIMITED | Engine Type: L4 | Liters: 2.4 Fuel Delivery: FI | Fuel: GAS REMOVAL Warning: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death. Illustration shown with instrument panel removed for clarity. Click to enlarge LHD model shown. RHD model similar. 1. Disconnect and isolate the negative battery cable. To aid in reinstallation, note the installed position of the mode control cable to the A/C-heater control prior to removal of the cable. 1. Remove the instrument panel center bezel and disconnect the mode control cable from the A/C-heater control (refer to 23 - BODY/INSTRUMENT PANEL/BEZEL- CENTER - REMOVAL). 2. On LHD models, remove the glove box (refer to 23 - BODY/INSTRUMENT PANEL/GLOVE BOX - REMOVAL). 3. Disengage the metal retaining clip (1) that secures the mode control cable (2) from the right side of the HVAC air distribution housing (3). To aid in reinstallation, note the position of the mode control cable as it passes through the instrument panel support prior to removal of the cable. 1. Disconnect the mode control cable from the mode door cam (4) and remove the cable from the vehicle. INSTALLATION Illustration shown with instrument panel removed for clarity.

Click to enlarge LHD model shown. RHD model similar. 1. Position the mode control cable (2) to the right side of the HVAC air distribution housing (3) through the opening in the instrument panel support. 2. Connect the mode control cable to the mode door cam (4). 3. Engage the metal retaining clip (1) to the right side of the HVAC air distribution housing. Make sure the retaining clip is fully engaged to the housing. 4. Connect the mode door control cable to the A/C-heater control and install the instrument panel center bezel (refer to 23 - BODY/INSTRUMENT PANEL/BEZEL-CENTER - INSTALLATION). 5. Visually verify the mode door cam moves from the full defrost position to the full panel position and then back to the full defrost position using the mode control knob on the A/C-heater control. If OK, go to step 10. If not OK, proceed to step 6. Caution: Failure to adjust the mode control cable when required can result in operating modes not being properly obtained. 1. Disengage the mode control cable from the metal retaining clip located on the right side of the HVAC housing. 2. Turn the mode control knob on the A/C-heater control to the full defrost position. 3. Reach behind the instrument panel and turn the mode door cam clockwise until it stops in the full defrost position and engage the mode control cable to the metal retaining clip. Make sure the cam is in the full defrost position and that the cable is fully engaged to the retaining clip. 4. Verify the mode door cam moves from the full defrost position to the full panel position and then back to the full defrost position as selected with the mode control knob on the A/C-heater control. If not, repeat steps 6 thru 9. 5. On LHD models, install the glove box (refer to 23 - BODY/INSTRUMENT PANEL/ GLOVE BOX - INSTALLATION). 6. Reconnect the negative battery cable.

2007 Jeep COMPASS Submodel: LIMITED | Engine Type: L4 | Liters: 2.4 Fuel Delivery: FI | Fuel: GAS REMOVAL Warning: Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death. Illustration shown with instrument panel removed for clarity. Click to enlarge LHD model shown. RHD model similar. 1. Disconnect and isolate the negative battery cable. To aid in reinstallation, note the installed position of the temperature control cable to the A/C-heater control prior to removal of the cable. 1. Remove the instrument panel center bezel and disconnect the temperature control cable from the A/C-heater control (refer to 23 - BODY/INSTRUMENT PANEL/BEZEL- CENTER - REMOVAL). 2. On RHD models, remove the glove box (refer to 23 - BODY/INSTRUMENT PANEL/ GLOVE BOX - REMOVAL). 3. Disengage the metal retaining clip (1) that secures the temperature control cable (2) from the left side of the HVAC air distribution housing (3). To aid in reinstallation, note the position of the temperature control cable as it passes through the instrument panel support prior to removal of the cable. 1. Disconnect the temperature control cable from the blend door pivot lever (4) and remove the cable from the vehicle. INSTALLATION Illustration shown with instrument panel removed for clarity.

2011 JEEP COMPASS MK Service and Repair Manual

You're Reading a Preview

Recently Viewed