2009-2015 Jaguar XF (X250)
2.2L, 3.0L Diesel & 2.0 L Petrol
6.
5.
4.
3.
2.
1.
Published: 11-May-2011
Body Closures - Front Door
Removal and Installation
Removal
NOTE: The front door is manufactured from
mild steel, it contains a side impact reinforcement
manufactured from boron steel.
The front door is serviced as a separate bolt-on panel.
For additional information relating to this repair procedure please
see the following:
For additional information, refer to: Health and Safety Precautions
(100-00 General Information, Description and Operation) /
(501-25A Body Repairs - General Information, Body Repairs
Description and Operation) /
(501-25B Body Repairs - Corrosion Protection, Corrosion Protection
Description and Operation) /
Body and Frame (501-26, Description and Operation).
NOTE: If the procedure includes removal of the front door
components, the battery can remain connected to aid their removal
and disconnected afterwards.
Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect
(414-01 Battery, Mounting and Cables, General Procedures).
NOTE: For new front door installation, this step may be
carried out later in the removal procedure.
Disconnect the front door wiring harness, accessed behind the
grommet on the A-pillar.
NOTE: For new front door installation, this step may be
carried out later in the removal procedure.
Release the front door check strap from the body.
NOTE: This step is for removing the fully trimmed front door
for access only, for installing a new front door, continue to removal
step 7.
15.
14.
13.
12.
11.
10.
9.
8.
7.
Remove the front door upper and lower hinge pivot bolts and lift the
front door to remove.
Remove the front door window regulator and motor.
For additional information, refer to: Front Door Window Regulator and
(501-11 Glass, Frames and Mechanisms, Removal and Motor
Installation).
Remove the exterior mirror.
For additional information, refer to: (501-09 Rear View Exterior Mirror
Mirrors, Removal and Installation).
Remove the front door latch.
For additional information, refer to: (501-14 Front Door Latch
Handles, Locks, Latches and Entry Systems, Removal and
Installation).
Remove the front door outer window frame mouldings.
Remove the front door weatherstrips.
Remove the front door wiring harness.
Remove the front door impact absorbers.
Remove the front door check strap.
Remove the front door glass run felt.
4.
3.
2.
1.
17.
16. Remove any miscellaneous front door clips, grommets and
blanking covers.
NOTE: If new hinges are being installed, install
the complete hinges to the A-pillar. To align the hinges
at the A-pillar it will be necessary to remove the front
fender.
Remove the upper and lower front door hinge fixing bolts
and remove the front door.
Installation
NOTE: If the front door has been removed for access only, it
can be installed back on to its upper and lower hinge pivots and
secured with the upper and lower hinge pivot bolts.
Offer up the front door and loosely install the front door hinge bolts.
Check alignment, if correct, proceed to next step, if not, rectify and
recheck before proceeding.
Tighten the front door hinge bolts to 30 Nm.
When correctly aligned and with the front door hinge bolts
tightened, the new front door can be removed at its upper and lower
hinge pivot bolts for refinishing.
5.
NOTE: Install the front door upper frame weatherstrip prior
to installing the front door.
The installation of associated panels and components is the reversal of
removal procedure.
Tighten the front door upper and lower hinge pivot bolts to 30
Nm.
5.
4.
3.
2.
1.
Published: 11-May-2011
Body Closures - Fuel Filler Door Assembly
Removal and Installation
Removal
CAUTION: Do not align the bowl using the hinge arm.
NOTE: Removal steps in this procedure may contain installation details.
WARNING: Do not work on or under a vehicle supported only
by a jack. Always support the vehicle on safety stands.
Raise and support the vehicle.
Refer to: Fuel Tank Filler Pipe (310-01, Removal and Installation).
1.
6.
CAUTION: Protect the surrounding paintwork to
avoid damage.
NOTE: Do not disassemble further if the component is
removed for access only.
Release the clip.
Installation
To install, reverse the removal procedure.
1.
2.
1.
Published: 11-May-2011
Body Closures - Fuel Filler Door
Removal and Installation
Removal
CAUTION: Do not align the bowl using the hinge arm.
NOTE: Removal steps in this procedure may contain installation details.
CAUTION: Protect the surrounding paintwork to
avoid damage.
Release the clip.
Installation
To install, reverse the removal procedure.
3.
2.
1.
Published: 31-May-2013
Body Closures - Liftgate Hinge
Removal and Installation
Removal
Refer to: (501-08 Exterior Trim and Ornamentation, Rear Spoiler
Removal and Installation).
Refer to: (501-05 Interior Trim and Headliner - Sportbrake
Ornamentation, Removal and Installation).
5.
4.
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$37.99
2009-2015 Jaguar XF Series (X250) Service & Repair Manual
Viewed 33 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$37.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
2009-2015 Jaguar XF Series (X250) Service & Repair Manual
Engines covered:
- 2.0L Turbocharged Ford Ecoboost I4
- 2.2L Ford Duratorq I4 (Diesel)
- 3.0L Ford AJD V6 (Diesel)
- 5.0L Supercharged Jaguar AJ133S V8
Format: .PDF
Printable: Yes
Language: English
Compatibility: Compatible with various electronic devices including PC, Mac computers, Android and Apple smartphones, and tablets.
Requirements: Requires Adobe Reader (free)
Whether you are a professional mechanic or a DIY enthusiast, this auto repair manual provides every troubleshooting and replacement procedure recommended by the manufacturer. It includes step-by-step instructions, clear images, and exploded-view illustrations.
Regular maintenance is essential for the durability of your vehicle. Over time, certain parts will wear out and require replacement.
A reliable car repair manual is invaluable as it offers the manufacturer's recommended troubleshooting charts and replacement procedures, enabling you to save on repairs, enhance your vehicle's reliability, and minimize visits to the repair shop.
Please note:
This is not a generic repair manual. It contains every troubleshooting and replacement procedure provided by the manufacturer, including step-by-step instructions, exploded-view illustrations, and clear images in an easy-to-use digital format.
Digital repair manuals are highly convenient as they can be accessed on various electronic devices without the need to flip through numerous pages. They are easily searchable, portable, and can be printed if desired.
