2009 Infiniti M35 Service & Repair Manual
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
ACC-1
ACCELERATOR CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
ACC
Revision: 2005 July 2006 M35/M45
ACCELERATOR CONTROL SYSTEM
PRECAUTIONS ......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 2
ACCELERATOR CONTROL SYSTEM ..................... 3
Components ............................................................ 3
Removal and Installation ......................................... 3
REMOVAL ............................................................ 3
INSTALLATION .................................................... 4
INSPECTION AFTER INSTALLATION ................. 4
ACC-2
PRECAUTIONS
Revision: 2005 July 2006 M35/M45
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” ABS00FH1
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
ACCELERATOR CONTROL SYSTEM
ACC-3
C
D
E
F
G
H
I
J
K
L
M
A
ACC
Revision: 2005 July 2006 M35/M45
ACCELERATOR CONTROL SYSTEM PFP:18005
Components ABS00FHE
Removal and Installation ABS00FH2
REMOVAL
1. Disconnect accelerator pedal position sensor harness connector.
2. Remove front kicking plate and dash side finisher. Refer to EI-37, " BODY SIDE TRIM " .
3. Remove the cap and the inside mounting nut, and then disassemble the accelerator pedal pad from the
floor carpet.
4. Press the pin (1) with long-nose pliers and pull them out in the
direction shown by the arrow ( ). Then remove the accelerator
pedal pad (2).
CAUTION:
Do not disengage the part (the link) other than pins.
5. Remove accelerator pedal stopper cover.
1. Accelerator pedal bracket and lever
assembly
2. Accelerator pedal stopper cover 3. Cap
4. Accelerator pedal pad 5. Pin
PBIC3203E
KBIA3594J
ACC-4
ACCELERATOR CONTROL SYSTEM
Revision: 2005 July 2006 M35/M45
6. Pull up the floor carpet.
7. Remove mounting nuts of accelerator pedal bracket.
8. Remove accelerator pedal bracket and lever assembly.
CAUTION:
● Do not disassemble accelerator lever. Do not remove accelerator pedal position sensor from
accelerator lever.
● Avoid impact from dropping etc. during handling.
● Be careful to keep accelerator lever away from water.
INSTALLATION
Installation is the reverse order of removal.
INSPECTION AFTER INSTALLATION
● Make sure accelerator pedal moves smoothly within the whole operation range when it is fully depressed
and released.
● Make sure accelerator pedal securely returns to the fully released position.
● For the electrical inspection of accelerator pedal position sensor, refer to the following.
– VQ35DE
EC-625, " DTC P2122, P2123 APP SENSOR " .
– VK45DE
EC-1357, " DTC P2122, P2123 APP SENSOR " .
CAUTION:
When harness connector of accelerator pedal position sensor is disconnected, perform “Acceler-
ator Pedal Released Position Learning”. Refer to EC-95, " Accelerator Pedal Released Position
Learning " (VQ35DE) or EC-805, " Accelerator Pedal Released Position Learning " (VK45DE).
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$36.99
Viewed 18 Times Today
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$36.99
If you are in need of a repair manual for your 2009 Infiniti M35, look no further. This accessible manual is perfect for both professional mechanics and DIY enthusiasts. In the past, traditional paper manuals were the norm, but now you can access the same valuable information in a more convenient and cost-effective digital format.
Whether you are looking to fix the brakes, engine, suspension, steering, drivetrain, electrical systems, heating, air conditioning, or perform standard maintenance, this manual has you covered. It provides comprehensive service information for your vehicle, allowing you to tackle any repair or maintenance task with confidence.
By utilizing this repair manual, you can save a significant amount of money on vehicle maintenance and repairs. Professional mechanics often charge high fees for their services, making a DIY approach a cost-effective alternative. The manual is compatible with Windows, Mac computers, smartphones, and tablets, ensuring ease of use across various devices.
