2003-2005 Honda Accord Service & Repair Manual Software
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing on Mac/PC
Software-Driven Manual
Full Search Facility
Print one or all pages of your manual
Single Use Fasteners and Components
Front Wheel Drive Shaft Nut
Front Wheel Drive Shaft Washer
Output Shaft Retaining Ring
Output Shaft Seal
Special Tools
Disc Brakes
07CH-42188-B Ball Joint Separator
Equivalent regional tools: Special Tools.
Front Suspension
07CH-43631 Ball Joint Separator
Equivalent regional tools: Special Tools.
Wheel Drive Shafts
07-J-45859 Axle Remover
Equivalent regional tools: Special Tools.
Warning: The battery must be disconnected to prevent the brake master cylinder from pressurizing the hydraulic system
during its automated self diagnostic tests that can possibly occur when a door is opened or the key transmitter is activated.
Failure to follow this precaution may cause personal injury.
Warning: Brake Dust Warning.
Removal Procedure
Warning: Always ensure the Battery Maintenance Mode is inactive before disconnecting the 12 volt battery. This mode can
be active with the ignition off, regardless of whether the vehicle charging cord is plugged in or not. When this mode is
active, the on-board high voltage battery charger will energize the 12 volt battery cables and charge the 12 volt battery.
Disconnecting the battery cables while this mode is active may result in an electrical shock or a burn from hot battery cable
leads.
1. Disconnect the battery negative cable. Battery Negative Cable Disconnection and Connection.
2. Remove the front tire and wheel assembly. Tire and Wheel Removal and Installation.
3. Have an assistant apply the brakes.
4. Front Wheelhouse Liner Bolt - Left Side and Right Side (1) >> Remove [6x]
Note: Left side shown, right side similar.
5. Front Tire Front Air Deflector - Left Side and Right Side (1) >> Remove [2x]
Note: Left side shown, right side similar.
6. Front Bumper Fascia Bolt (1) >> Remove [10x]
7. Underbody Front Air Deflector Bolt (1) >> Remove [9x]
8. Underbody Front Air Deflector Retainer (2) >> Remove [2x]
9. Front Compartment Insulator (1) >> Remove
Note: The proper position of the front compartment insulator (1) is above the front bumper lower fascia and the left and right side front
wheelhouse liners.
10. Front Wheel Drive Shaft Nut (1) >> Remove and DISCARD
Caution: DO NOT use air tools to remove the wheel drive shaft nut. Damage to the wheel drive shaft threads could occur. Use hand
tools only.
11. Have an assistant release the brakes.
12. Install the 07-J-45859 Axle Remover (2) to the front wheel hub and secure with 2 wheel nuts (1) hand tightened.
13. Using the 07-J-45859 Axle Remover (2), release the front wheel drive half shaft from the front wheel hub.
14. Remove the 2 wheel nuts (1) and the 07-J-45859
Axle Remover (2) from the front wheel hub.
15. Front Wheel Speed Sensor Bolt (1) >> Remove [2x]
16. Front Wheel Speed Sensor (2) @ Steering Knuckle >> Remove
17. Front Brake Hose Bracket Bolt (1) >> Remove
18. Front Brake Hose (2) @ Steering Knuckle >> Reposition
19. Front Brake Caliper Bracket Bolt (2) >> Remove [2x]
Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the
hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear
the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.
20. Remove the front brake caliper and bracket assembly (1) and support with heavy mechanics wire.
21. Using a suitable jack, support the steering knuckle.
22. Place match marks on the steering linkage inner tie rod nut and the steering linkage inner tie rod.
23. Steering Linkage Inner Tie Rod Nut (1) >> Loosen
24. Steering Linkage Outer Tie Rod Nut (1) >> Loosen
25. Using 07CH-42188-B Ball Joint Separator (1), separate the steering linkage outer tie rod (2) from the steering knuckle.
Caution: Do not attempt to disconnect a steering linkage joint by driving a wedge between the joint and the attached part. Seal
damage may result which will cause premature failure of the joint.
26. Steering Linkage Outer Tie Rod Nut (1) >> Remove
27. Steering Linkage Outer Tie Rod (1) » Remove
28. Front Upper Control Arm Ball Stud Nut (1) >> Loosen
Note: DO NOT allow the ball stud to rotate while loosening the nut.
29. Using the 07CH-43631 Ball Joint Separator (1), separate the front control front link (2) from the steering knuckle.
30. Remove the 07CH-43631 Ball Joint Separator (1) from the front control front link (2) and the steering knuckle.
31. Front Upper Control Arm Ball Stud Nut (1) >> Remove
32. Front Upper Control Arm Ball Stud Nut (1) >> Loosen
Note: DO NOT allow the ball stud to rotate while loosening the nut.
33. Using the 07CH-43631 Ball Joint Separator (1), separate the front control rear link (2) from the steering knuckle.
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing on Mac/PC
Software-Driven Manual
Full Search Facility
Print one or all pages of your manual
$24.99
Viewed 21 Times Today
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing on Mac/PC
Software-Driven Manual
Full Search Facility
Print one or all pages of your manual
$24.99
Provide lasting solutions via structured service resources with the 2003-2005 Honda Accord Service & Repair Manual Software, your essential companion for maintaining and repairing one of Honda's most beloved models. This comprehensive software provides detailed instructions for crucial components, including the intricate timing belt replacement and the efficient brake system inspection, ensuring you tackle repairs with confidence. Featuring high-quality visual aids and expertly crafted guidance, you’ll find everything you need to perform tasks like transmission fluid changes and electrical system troubleshooting without the hassle of hunting down information. One standout benefit of this software is its ability to empower DIY enthusiasts and professional mechanics alike with dealership-grade repair techniques at your fingertips, saving you time and costly trips to the garage.
NOTE: This is a sample. Your actual software manual may differ slightly.
The 2003-2005 Honda Accord Service & Repair Manual Software is a comprehensive guide that provides detailed information and step-by-step instructions to help you service, maintain, and repair your Honda Accord for the model years 2003, 2004, and 2005. Whether you are a professional mechanic or a Honda Accord owner aiming to reduce repair costs, this software manual is an essential resource.
- Accord 2003
- Accord 2004
- Accord 2005
With this manual software, you will have access to accurate repair procedures, diagnostic diagrams, illustrations, and precise technical specifications that cover everything from routine maintenance tasks like oil changes to intricate engine and system repairs. It is meticulously designed to guide you through every repair or maintenance task with clarity and accuracy.
Key features of the 2003-2005 Honda Accord Service & Repair Manual Software include:
- Detailed vehicle information for Accord models from 2003 to 2005
- Engine performance details and maintenance procedures
- Electrical and electronic system troubleshooting and repair instructions
- Transmission and drivetrain servicing methods
- Brake, suspension, and steering system repair guidelines
- Heating, ventilation, and air conditioning maintenance procedures
- Comprehensive wiring diagrams and schematics
By utilizing this Honda Accord Service & Repair Manual Software, you can save time and money by handling repairs and maintenance tasks on your own. Its clear instructions, comprehensive illustrations, and detailed technical information make it easy to follow and understand all procedures.
Invest in the 2003-2005 Honda Accord Service & Repair Manual Software today to keep your Accord performing at its best for years to come.
