Single Use Fasteners and Components Front Wheel Drive Shaft Nut Front Wheel Drive Shaft Washer Output Shaft Retaining Ring Output Shaft Seal Special Tools Disc Brakes 07CH-42188-B Ball Joint Separator Equivalent regional tools: Special Tools. Front Suspension 07CH-43631 Ball Joint Separator Equivalent regional tools: Special Tools. Wheel Drive Shafts 07-J-45859 Axle Remover Equivalent regional tools: Special Tools. Warning: The battery must be disconnected to prevent the brake master cylinder from pressurizing the hydraulic system during its automated self diagnostic tests that can possibly occur when a door is opened or the key transmitter is activated. Failure to follow this precaution may cause personal injury. Warning: Brake Dust Warning. Removal Procedure Warning: Always ensure the Battery Maintenance Mode is inactive before disconnecting the 12 volt battery. This mode can be active with the ignition off, regardless of whether the vehicle charging cord is plugged in or not. When this mode is active, the on-board high voltage battery charger will energize the 12 volt battery cables and charge the 12 volt battery. Disconnecting the battery cables while this mode is active may result in an electrical shock or a burn from hot battery cable leads. 1. Disconnect the battery negative cable. Battery Negative Cable Disconnection and Connection. 2. Remove the front tire and wheel assembly. Tire and Wheel Removal and Installation. 3. Have an assistant apply the brakes. 4. Front Wheelhouse Liner Bolt - Left Side and Right Side (1) >> Remove [6x]
Note: Left side shown, right side similar. 5. Front Tire Front Air Deflector - Left Side and Right Side (1) >> Remove [2x] Note: Left side shown, right side similar. 6. Front Bumper Fascia Bolt (1) >> Remove [10x]
7. Underbody Front Air Deflector Bolt (1) >> Remove [9x] 8. Underbody Front Air Deflector Retainer (2) >> Remove [2x] 9. Front Compartment Insulator (1) >> Remove
Note: The proper position of the front compartment insulator (1) is above the front bumper lower fascia and the left and right side front wheelhouse liners. 10. Front Wheel Drive Shaft Nut (1) >> Remove and DISCARD Caution: DO NOT use air tools to remove the wheel drive shaft nut. Damage to the wheel drive shaft threads could occur. Use hand tools only. 11. Have an assistant release the brakes. 12. Install the 07-J-45859 Axle Remover (2) to the front wheel hub and secure with 2 wheel nuts (1) hand tightened.
13. Using the 07-J-45859 Axle Remover (2), release the front wheel drive half shaft from the front wheel hub. 14. Remove the 2 wheel nuts (1) and the 07-J-45859 Axle Remover (2) from the front wheel hub. 15. Front Wheel Speed Sensor Bolt (1) >> Remove [2x] 16. Front Wheel Speed Sensor (2) @ Steering Knuckle >> Remove 17. Front Brake Hose Bracket Bolt (1) >> Remove
18. Front Brake Hose (2) @ Steering Knuckle >> Reposition 19. Front Brake Caliper Bracket Bolt (2) >> Remove [2x] Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak. 20. Remove the front brake caliper and bracket assembly (1) and support with heavy mechanics wire. 21. Using a suitable jack, support the steering knuckle. 22. Place match marks on the steering linkage inner tie rod nut and the steering linkage inner tie rod. 23. Steering Linkage Inner Tie Rod Nut (1) >> Loosen
24. Steering Linkage Outer Tie Rod Nut (1) >> Loosen 25. Using 07CH-42188-B Ball Joint Separator (1), separate the steering linkage outer tie rod (2) from the steering knuckle.
Caution: Do not attempt to disconnect a steering linkage joint by driving a wedge between the joint and the attached part. Seal damage may result which will cause premature failure of the joint. 26. Steering Linkage Outer Tie Rod Nut (1) >> Remove 27. Steering Linkage Outer Tie Rod (1) » Remove
28. Front Upper Control Arm Ball Stud Nut (1) >> Loosen Note: DO NOT allow the ball stud to rotate while loosening the nut. 29. Using the 07CH-43631 Ball Joint Separator (1), separate the front control front link (2) from the steering knuckle.
30. Remove the 07CH-43631 Ball Joint Separator (1) from the front control front link (2) and the steering knuckle. 31. Front Upper Control Arm Ball Stud Nut (1) >> Remove 32. Front Upper Control Arm Ball Stud Nut (1) >> Loosen Note: DO NOT allow the ball stud to rotate while loosening the nut. 33. Using the 07CH-43631 Ball Joint Separator (1), separate the front control rear link (2) from the steering knuckle.
Take the fast track to precise fixes with the "2004 Honda Accord Repair Manual," your ultimate guide for maintaining and repairing one of the most popular sedans on the road. This comprehensive resource dives deep into essential components, including the intricate workings of the VTEC engine and the sophisticated brake system, ensuring you have the knowledge to tackle any issue head-on. With detailed illustrations and easy-to-follow instructions, this manual provides dealership-quality insights without the hefty price tag, allowing you to save both time and money while boosting your confidence in DIY repairs. One standout benefit of the "2004 Honda Accord Repair Manual" is its focus on preventative maintenance, helping you identify potential issues before they escalate into costly repairs.
NOTE: This is a sample. Your actual software manual may differ slightly.
The Repair manual for the 2004 Honda Accord provides comprehensive information on maintaining and repairing this vehicle model. This manual is an essential tool for both professional mechanics and DIY enthusiasts who want to ensure their Honda Accord remains in optimal condition. Below are some of the key sections included in the Repair manual:
Introduction This section offers an overview of the 2004 Honda Accord, including its specifications and features.
General Maintenance Guidelines for routine maintenance tasks such as oil changes, tire rotations, and fluid checks.
Engine Repair Detailed instructions for servicing the engine, including timing belt replacement, valve adjustments, and more.
Transmission Procedures for inspecting, maintaining, and repairing the transmission system.
Brakes Information on brake system maintenance, including how to replace brake pads and bleed the brakes.
Suspension and Steering Guidelines for checking and servicing the suspension and steering systems.
Electrical System Diagrams and troubleshooting tips for the vehicle's electrical components.
Body and Interior Instructions for repairing body panels, interior trim, and other non-mechanical components.
Troubleshooting A comprehensive guide to diagnosing common issues based on symptoms and error codes.
This Repair manual is designed to be user-friendly, with step-by-step instructions and clear diagrams to assist with all types of repairs and maintenance tasks. Whether you are a seasoned mechanic or a first-time car owner, the 2004 Honda Accord Repair manual is an invaluable resource for keeping your vehicle running smoothly.
Lifetime Access
