2003-2008 Honda Accord Service & Repair Manual Software
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing on Mac/PC
Software-Driven Manual
Full Search Facility
Print one or all pages of your manual
Single Use Fasteners and Components
Front Wheel Drive Shaft Nut
Front Wheel Drive Shaft Washer
Output Shaft Retaining Ring
Output Shaft Seal
Special Tools
Disc Brakes
07CH-42188-B Ball Joint Separator
Equivalent regional tools: Special Tools.
Front Suspension
07CH-43631 Ball Joint Separator
Equivalent regional tools: Special Tools.
Wheel Drive Shafts
07-J-45859 Axle Remover
Equivalent regional tools: Special Tools.
Warning: The battery must be disconnected to prevent the brake master cylinder from pressurizing the hydraulic system
during its automated self diagnostic tests that can possibly occur when a door is opened or the key transmitter is activated.
Failure to follow this precaution may cause personal injury.
Warning: Brake Dust Warning.
Removal Procedure
Warning: Always ensure the Battery Maintenance Mode is inactive before disconnecting the 12 volt battery. This mode can
be active with the ignition off, regardless of whether the vehicle charging cord is plugged in or not. When this mode is
active, the on-board high voltage battery charger will energize the 12 volt battery cables and charge the 12 volt battery.
Disconnecting the battery cables while this mode is active may result in an electrical shock or a burn from hot battery cable
leads.
1. Disconnect the battery negative cable. Battery Negative Cable Disconnection and Connection.
2. Remove the front tire and wheel assembly. Tire and Wheel Removal and Installation.
3. Have an assistant apply the brakes.
4. Front Wheelhouse Liner Bolt - Left Side and Right Side (1) >> Remove [6x]
Note: Left side shown, right side similar.
5. Front Tire Front Air Deflector - Left Side and Right Side (1) >> Remove [2x]
Note: Left side shown, right side similar.
6. Front Bumper Fascia Bolt (1) >> Remove [10x]
7. Underbody Front Air Deflector Bolt (1) >> Remove [9x]
8. Underbody Front Air Deflector Retainer (2) >> Remove [2x]
9. Front Compartment Insulator (1) >> Remove
Note: The proper position of the front compartment insulator (1) is above the front bumper lower fascia and the left and right side front
wheelhouse liners.
10. Front Wheel Drive Shaft Nut (1) >> Remove and DISCARD
Caution: DO NOT use air tools to remove the wheel drive shaft nut. Damage to the wheel drive shaft threads could occur. Use hand
tools only.
11. Have an assistant release the brakes.
12. Install the 07-J-45859 Axle Remover (2) to the front wheel hub and secure with 2 wheel nuts (1) hand tightened.
13. Using the 07-J-45859 Axle Remover (2), release the front wheel drive half shaft from the front wheel hub.
14. Remove the 2 wheel nuts (1) and the 07-J-45859
Axle Remover (2) from the front wheel hub.
15. Front Wheel Speed Sensor Bolt (1) >> Remove [2x]
16. Front Wheel Speed Sensor (2) @ Steering Knuckle >> Remove
17. Front Brake Hose Bracket Bolt (1) >> Remove
18. Front Brake Hose (2) @ Steering Knuckle >> Reposition
19. Front Brake Caliper Bracket Bolt (2) >> Remove [2x]
Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the
hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear
the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.
20. Remove the front brake caliper and bracket assembly (1) and support with heavy mechanics wire.
21. Using a suitable jack, support the steering knuckle.
22. Place match marks on the steering linkage inner tie rod nut and the steering linkage inner tie rod.
23. Steering Linkage Inner Tie Rod Nut (1) >> Loosen
24. Steering Linkage Outer Tie Rod Nut (1) >> Loosen
25. Using 07CH-42188-B Ball Joint Separator (1), separate the steering linkage outer tie rod (2) from the steering knuckle.
Caution: Do not attempt to disconnect a steering linkage joint by driving a wedge between the joint and the attached part. Seal
damage may result which will cause premature failure of the joint.
26. Steering Linkage Outer Tie Rod Nut (1) >> Remove
27. Steering Linkage Outer Tie Rod (1) » Remove
28. Front Upper Control Arm Ball Stud Nut (1) >> Loosen
Note: DO NOT allow the ball stud to rotate while loosening the nut.
29. Using the 07CH-43631 Ball Joint Separator (1), separate the front control front link (2) from the steering knuckle.
30. Remove the 07CH-43631 Ball Joint Separator (1) from the front control front link (2) and the steering knuckle.
31. Front Upper Control Arm Ball Stud Nut (1) >> Remove
32. Front Upper Control Arm Ball Stud Nut (1) >> Loosen
Note: DO NOT allow the ball stud to rotate while loosening the nut.
33. Using the 07CH-43631 Ball Joint Separator (1), separate the front control rear link (2) from the steering knuckle.
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing on Mac/PC
Software-Driven Manual
Full Search Facility
Print one or all pages of your manual
$28.99
Viewed 29 Times Today
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing on Mac/PC
Software-Driven Manual
Full Search Facility
Print one or all pages of your manual
$28.99
Lift DIY results using detailed 2003-2008 Honda Accord Service & Repair Manual Software, your ultimate companion for maintaining and repairing your vehicle with confidence! This comprehensive software provides in-depth insights and professional-grade instructions to tackle everything from replacing the timing belt to diagnosing electrical issues with the multi-information display. With user-friendly navigation and high-quality illustrations, you'll find it easier than ever to understand complex repairs such as brake system overhauls or suspension adjustments. The unique benefit of this software is its extensive database of troubleshooting tips and techniques, enabling car enthusiasts and novices alike to perform repairs that meet or exceed dealership standards. Empower yourself with the knowledge and skills to keep your Honda Accord running smoothly for years to come.
NOTE: This is a sample. Your actual software manual may differ slightly.
Introducing the 2003-2008 Honda Accord Service & Repair Manual Software!
Own a Honda Accord from 2003 to 2008? This comprehensive software manual is designed specifically for these models, making it the perfect companion for any DIY enthusiast or professional mechanic. It provides detailed step-by-step instructions and illustrative diagrams to help tackle any repair or maintenance task with ease.
From routine maintenance to complex repairs, this software format covers it all — including oil changes, brake pad replacements, and electrical fixes — ensuring you have the technical support you need at your fingertips.
Features:
- Complete coverage for the 2003-2008 Honda Accord models
- Detailed step-by-step instructions and clear illustrations
- Easy-to-follow format for quick and efficient repairs
- Clear explanations of complex procedures
- Maintenance schedules and recommended procedures
- Wiring diagrams and troubleshooting guides
- Tips and tricks to save time and money
This service and repair manual software provides the confidence and knowledge to take control of your Honda Accord's maintenance and repairs. Say goodbye to expensive dealership visits and hello to the satisfaction of DIY repairs.
Don't let minor issues or routine maintenance tasks slow you down. Get your hands on the 2003-2008 Honda Accord Service & Repair Manual Software today and unlock the full potential of your vehicle.
