1
WORKSHOP
REPAIR MANUAL
GENERAL INFORMATION 0
HEATING AND VENTILATION
BRAKES
MAIN INDEX
ISUZU
CONTENTS
WHEELS AND TYRES
4
5
BODY 8
SECURITY 11
SUSPENSION
3
STEERING
2
AXLE
FRAME AND CAB
ENGINE 6
TRANSMISSION 7
MY 2007
RESTRAINTS 9
CAB 10
BACK TO FRONT PAGE
KB P190
ISUZU KB P190 2007
GENERAL INFORMATION 0-1
SECTION 0
GENERAL INFORMATION
TABLE OF CONTENTS
PAGE
Section 0A General Informantion ...........................................................................................3
Section 0B Maintainance and Lubrication............................................................................... 19
TO MODEL INDEX
BACK TO MAIN INDEX ISUZU KB P190 2007
SECTION 0A
GENERAL INFORMATION
TABLE OF CONTENTS
GENERAL INFORMATION 0A-1
General Repair Instructions ........................................................................................... 0A- 2
PAGE
Notes on the Format of this Manual............................................................................... 0A- 3
Identification .................................................................................................................... 0A- 6
Lifting Instructions .......................................................................................................... 0A- 7
Conversion Table ............................................................................................................ 0A- 9
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
0A-2 GENERAL INFORMATION
GENERAL REPAIR INSTRUCTIONS
1.Park the vehicle on level ground and chock the front or rear wheels before lifting the vehicle.
2.Raise the vehicle with a jack set against the axle or the frame.
3.Support the vehicle on chassis stands.
4.Use covers on the vehicle body, seats, and floor to prevent damage and/or contamination.
5.Disconnect the grounding cable from the battery before performing service operations.
This will prevent cable damage or burning due to short circuiting.
6.Handle brake fluid and antifreeze solution with great care.
Spilling these liquids on painted surfaces will damage the paint.
7.The use of the proper tool(s) and special tool(s) where specified is essential to efficient, reliable, and safe
service operations.
8.Always use genuine ISUZU replacement parts.
9.Discard used cotter pins, gaskets, O-rings, oil seals, lock washers, and self-locking nuts at disassembly.
Normal function of these parts cannot be guaranteed if they are reused.
10.Prepare new cotter pins, gaskets, O-rings, oil seals, lock washers, and self-locking nuts for installation.
11.Keep the disassembled parts neatly in groups.
This will facilitate smooth and correct reassembly.
12.Keep fixing nuts and bolts separate.
Fixing nuts and bolts vary in hardness and design according to installation position.
13.Clean all parts before inspection or reassembly.
14.Clean the oil ports and other openings with compressed air to make certain that they are free from dirt and
obstructions.
15.Lubricate the rotating and sliding faces of all moving parts with oil or grease before installation.
16.Use the recommended liquid gasket to prevent leakage.
17.Carefully observe all nut and bolt torque specifications.
18.When removing or replacing parts that require refrigerant to the discharged from the air conditioning system, be
sure to use the Vehicle Refrigerant Recovery and Recycling Equipment (VRRRE) to recover and recycle R134a,
to promote the aim of the protection of the ozone layer covering the earth.
19.Check and recheck your work. No service operation is complete until you have done this.
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
GENERAL INFORMATION 0A-3
NOTES ON THE FORMAT OF THIS MANUAL
1. Find the applicable section by referring to the index at the front of the Workshop Manual binder.
2. The following technical service information is included in this Section:
• Identification
• Maintenance schedules
• Recommended Iubricants
• Recommended fuels
• Oil viscosity charts
3. Individual sections of this Workshop Manual are divided into the following categories:
• Main data and specifications
• Torque specifications
• Recommended liquid gasket
• Loctite application procedure
• Servicing
• Removal and installation
• Disassembly
• Inspection and repair
• Reassembly
• Troubleshooting
4. Each "Major Components" page of this Workshop Manual has an exploded view of the applicable area.
A brief explanation of the notation used follows:
BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$39.99
2008-2012 Holden Colorado Isuzu Dmax Rodeo RA7 Service & Repair Manual
Viewed 25 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$39.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
- Essential resource for owners and mechanics of Holden Colorado, Isuzu Dmax, and Isuzu Rodeo RA7 models from 2008 to 2012
- Comprehensive information on repairing and servicing these specific vehicle models
- Designed for both professional mechanics and DIY enthusiasts
This repair manual covers a wide range of topics, including engine, transmission, electrical systems, suspension, steering, brakes, and more. It provides detailed instructions and diagrams to help you tackle any maintenance or repair task with confidence.
Its user-friendly format allows for easy navigation, while detailed illustrations and step-by-step instructions provide a clear understanding of the repair procedures. This makes it easier to troubleshoot and fix any issues with your vehicle.
Investing in this repair manual will save you time and money by enabling you to handle repairs and maintenance tasks on your own. Keep your vehicle in top condition and extend its lifespan with the help of this comprehensive resource.
