NUOVA BRAVO 1.4 16v POWER UNIT RIGID SUPPORT - GEARBOX
SIDE - R.R. 1008A42
Removing ( Refitting )
Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.
Op. 5530B10 BATTERY - R+R
Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R
Op. 1008B30 GEARBOX SIDE SUPPORT FLEXIBLE MOUNTING(S) -
REPLACE
1. Undo the bolt fixing the air pipe to the rigid support.
2. Undo the bolts (2a) and remove the rigid support (2b).
Refitting ( Removing )
- Place the rigid mounting in its housing and tighten the bolts to the
recommended torque.
- Tighten the bolt fixing the air pipe to the rigid support.
Op. 1008B30 GEARBOX SIDE SUPPORT FLEXIBLE MOUNTING(S) -
REPLACE
Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R
Op. 5530B10 BATTERY - R+R
Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.
Component Fastening dia
Value
(daNm)
Validity
Gearbox side
power unit
rigid support
Bolt (to be
replaced)
M10 5.0 ÷ 6.0
Page 1 of 1 - Contents
8/1/2024 file://C:\
2024 Kia Soul
2024 Kia Soul
2024 Kia
2024 Kia So 2024 Kia So 2024 Kia So
NUOVA BRAVO 1.9 JTD 8v SINGLE CYLINDER HEAD OR (ONE) LEFT
OR RIGHT, REMOVED - GRINDING 1016E38
- Check that the planarity of the lower cylinder head plane corresponds
to the recommended values.
1. If the lower surface flatness of the lower cylinder head is not within
specified values, grind from the nominal head height and then fit a new
gasket with the number of notches determined as described below.
a - The head may be levelled to 0.1 m if starting from a gasket with no
references and using a new gasket with one reference.
b - The head may be levelled to 0.2 m if starting from a gasket with no
references and using a new gasket with two references.
c - The head may be levelled to 0.1 m if starting from a gasket with one
reference and using a new gasket with two references.
Measurement Value Validity
Engine cylinder head
lower surface flatness
(mm)
< 0.1
When within limit conditions (head gasket with 2 notches before
levelling), the lower cylinder head surface cannot be levelled.
Measurement Value Validity
Cylinder head nominal
height (mm)
107 +/- 0.05 1.9 JTD 16v
Page 1 of 1 - Contents
8/1/2024 file://C:\ html
2024 Kia Soul
2024 Kia Soul
2024 Kia Soul
NUOVA BRAVO 1.4 16v TOOTHED TIMING BELT - R + R FOR TIMING
ADJUSTMENT OR REPLACEMENT 1032B10
Removing ( Refitting )
- Position the vehicle on a lift.
Op. 4450B04 RIGHT FRONT WHEEL - R.R
Op. 1016A10 SOUND-PROOFING COVER - R.R
Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.
Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT
WHEEL ARCH - R.R.
Op. 1092G10 SINGLE ENGINE BELT - R.R
Op. 1092A10 CRANKSHAFT PULLEY - R + R
Op. 1092G14 ENGINE COMPONENT SINGLE BELT MOVING
TENSIONER - R + R
Op. 1092G20 ENGINE COMPONENT SINGLE BELT FIXED TENSIONER
- R + R
Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R
1. Remove the front plug (1a) and fit the camshaft timing tool (1b) to
the camshaft housing.
Check that the tool is correctly inserted in the housing in the
exhaust side camshaft, rotating the crankshaft until the pin for the
tool can be heard engaging correctly in the housing in the
camshaft.
Tool Description Function Validity
1870896900 Templates Engine tuning 1.9 JTD 16v
1. Undo the bolt fixing the crankcase front cover shown in the diagram.
2. Fit the tool (2a) provisionally and fasten it using the calibrated screw
(2b) and the nut.
Tool Description Function Validity
1860905000 Template Engine tuning 1.9 JTD
Page 1 of 4 - Contents
8/1/2024 file://C:\ html
2024 Kia Soul
2024 Kia Soul
2024 Kia Soul
Tool Description Function Validity
1860905010 Calibrated screw Engine tuning 1.9 JTD
- Remove the timing tools positioned previously.
1. Loosen the nut retaining the timing belt moving tensioner.
2. Release and remove the toothed timing drive belt.
Refitting ( Removing )
1. Loosen the bolt securing the exhaust side timing belt toothed driven
pulley.
- Fit the timing drive belt on the drive gear, checking that the belt teeth
are correctly inserted in the gear grooves.
- Position the template for measuring TDC and fasten it using the
calibrated screw.
Tool Description Function Validity
1860905000 Template Engine tuning 1.9 JTD
Page 2 of 4 - Contents
8/1/2024 file://C:\ html
2024 Kia Soul
2024 Kia Soul
2024 Kia Soul
1. Fully fit the toothed timing drive belt.
2. Use a screwdriver on the tensioner (2a) tab for leverage until the
reference (2b) is in the maximum tension position, then lock the nut (2c)
fixing the moving tensioner in this position.
- Remove the timing tools.
3. Loosen the nut fixing hte moving tensioner and align the moving
reference (3a) with the opening (3b), i.e. adjust to nominal tension
position and then tighten nut (3c) securing the belt tensioner to torque.
4. Tighten the bolt fixing the exhaust side camshaft toothed driven pulley
to the recommended torque.
Tool Description Function Validity
1860905010 Calibrated screw Engine tuning 1.9 JTD
Component Fastening dia
Value
(daNm)
Validity
Timing
system
moving
tensioner
Nut M8 2.3 ÷ 2.8 1.9 JTD
Component Fastening dia
Value
(daNm)
Validity
Driven
timing
toothed
pulley
Bolt M12
2.8 ÷ 3.1 +
40°
1.9 JTD
- Rotate the crankshaft through two revolutions.
- Recheck the timing by refitting the timing tools.
- Check the moving timing belt tensioner references are aligned.
- Tighten the bolt fixing the previously removed crankcase front cover.
Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R
Only fit the exhaust side camshaft template because the intake side
template seat is not accessible.
Page 3 of 4 - Contents
8/1/2024 file://C:\ html
2024 Kia Soul
2024 Kia Soul
2024 Kia Soul
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$31.99
1987-1991 Fiat 126 Bis Service & Repair Manual
Viewed 39 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$31.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Description
The FIAT 126 Bis 1987-1991 Service Repair Manual is a comprehensive guide that will assist you in maintaining and repairing your FIAT 126 Bis vehicle. Whether you are a professional mechanic or a DIY enthusiast, this manual provides detailed step-by-step instructions, diagrams, and illustrations to help you carry out any necessary repairs or maintenance tasks.
This service repair manual covers the FIAT 126 Bis models produced between 1987 and 1991. It includes information on various components and systems, including engine, transmission, suspension, brakes, electrical system, and more. With this manual, you'll have all the information you need to troubleshoot and repair any issues that may arise with your vehicle.
Some of the features and benefits of this service repair manual include:
- Clear and concise instructions: The manual provides easy-to-understand instructions, allowing both experienced technicians and beginners to carry out repairs and maintenance tasks.
- Detailed diagrams and illustrations: Visual aids are provided to help you better understand the procedures and identify the components involved in each repair.
- Comprehensive coverage: This manual covers all aspects of the FIAT 126 Bis, ensuring that you have the necessary information to tackle any repair or maintenance task with confidence.
- Time and money-saving: By following the instructions in this manual, you'll be able to save time and money by avoiding unnecessary visits to the mechanic.
- Compatibility: This manual is specifically designed for the FIAT 126 Bis models produced between 1987 and 1991, ensuring accurate and relevant information for your vehicle.
Whether you need to perform routine maintenance, such as oil changes and fluid replacement, or tackle more complex repairs, the FIAT 126 Bis 1987-1991 Service Repair Manual is an indispensable resource that will guide you every step of the way.
