2010 Cadillac SRX Service & Repair Manual

CADILLAC SRX BRAKES 22-10 • DRIVE TRAIN 22-19 ANTI-LOCK BRAKE SYSTEM (ABS) 22-10 General Information 22-10 Precautions 22-10 Speed Sensors 22-10 Removal & Installation: 22-10 BLEEDING THE BRAKE SYSTEM 22-11 Bleeding Procedure .". 22-11 Bleeding the ABS System 22-11 Fluid Fill Procedure 22-13 Hydraulic Brake System Bleeding 22-12 Master Cylinder Bench. Bleeding 22-13 FRONT DISC BRAKES 22-14 Brake Caliper 22-14 Removal & Installation. 22-14 Disc Brake Pads 22-14 Removal & Installation 22-14 PARKING BRAKE 22-16 Parking Brake Cables 22-16 Adjustment 22-16 Parking Brake Shoes 22-16 Parking Brake Adjuster Disabling... 22-17 Parking Brake Adjuster Enabling :22-17 Removal & Installation 22-16 REAR DISC BRAKES 22-15 Brake Caliper..... 22-15 Removal & Installation 22-15 Disc Brake Pads ....22-16 Removal & Installation 22-16 CHASSIS ELECTRICAL 22-18 AIR BAG (SUPPLEMENTAL RESTRAINT SYSTEM) 22-18 General Information .' 22-18 Arming the System 22-18 Clockspring Centering 22-19 Disarming the System 22-18 Service Precautions 22-18 Automatic Transmission Fluid 22-19 Checking Fluid ....22-19 Fluid Refill .22-19 Front Halfshaft 22-21 Removal & Installation 22-21 Rear Axle Fluid -. 22-21 Drain & Refill 22-21 Rear Driveshaft (Propeller Shaft) 22-22 Removal & Installation 22-22 Rear Halfshaft 22-22 Removal & Installation 22-22 Transfer Case Assembly 22-20 Removal & Installation 22-20 ENGINE COOLING 22-23 Engine Coolant 22-23 Drain & Refill Procedure 22-23 Flushing 22-23 Engine Fan 22-23 Removal & Installation 22-23 Radiator 22-24 Removal & Installation 22-24 Thermostat 22-24 Removal & Installation 22-24 Water Pump 22-24 Removal & Installation 22-24 ENGINE ELECTRICAL 22-25 BATTERY SYSTEM 22-25 Battery 22-25 Removal & Installation 22-25 CHARGING SYSTEM 22-26 Alternator 22-26 Removal & Installation 22-26 IGNITION SYSTEM 22-26 Firing Order 22-26 Ignition Coil 22-26 Removal & Installation 22-26 Ignition Timing 22-26 Adjustment 22-26 SparkPlugs 22-26 Removal & Installation...' 22-26 STARTING SYSTEM 22-27 Starter 22-27 Removal & Installation 22-27 ENGINE MECHANICAL 22-27 Accessory Drive Belts 22-27 Accessory BELT Routing 22-27 Adjustment 22-27 Inspection 22-27 Removal & Installation 22-27 Air Cleaner 22-27 Filter/element Replacement 22-28 Removal & Installation 22-27 Camshaft and Valve Lifters 22-28 Inspection 22-28 Removal & Installation 22-28 Catalytic Converter/ Exhaust Manifold 22-30 .Removal & Installation 22-30 Crankshaft Front Seal 22-32 Removal & Installation 22-32 Cylinder Head 22-32 Removal & Installation 22-32 Engine Oil & Filter 22-34 Replacement 22-34 Exhaust Manifold 22-34 Removal & Installation 22-34 Intake Manifold • 22-35 Removal & Installation 22-35 Oil Pan 22-35 Removal & Installation 22-35. Oil Pump..... 22-36 Inspection 22-36 Removal & Installation 22-36 Piston and Ring ,...22-36 Positioning 22-36 Rear Main Seal 22-36 ' Removal & Installation 22-36 Timing Chain & Sprockets 22-41 Removal & Installation 22-41 Timing Chain Front Cover 22-37 Removal & Installation..: 22-37 Turbocharger 22-43 Removal & Installation 22-43

22-2 CADILLAC SRX Valve Covers 22-43 Removal & Installation 22-43 Valve Lash 22-44 Adjustment 22-44 ENGINE PERFORMANCE & EMISSION CONTROLS .....22-44 Camshaft Position (CMP) Sensor 22-44 Location 22-44 Removal & Installation :..22-44 Crankshaft Position (CKP) Sensor : 22-45 Location 22-45 Removal & Installation 22-45 Electronic Control Module (ECM) 22-45 Location 22-45 Removal & Installation 22-45 Engine Coolant Temperature (ECT) Sensor 22-45 Location 22-45 Removal & Installation 22-45 Heated Oxygen (H02S) Sensor -. 22-45 Location 22-45 Removal & Installation 22-46 Intake Air Temperature (IAT) Sensor 22-47 Location 22-47 Removal & Installation 22-47 Knock Sensor (KS) 22-47 Location 22-47 Removal & Installation 22-47 Manifold Absolute Pressure (MAP) Sensor 22-47 Location 22-47 Removal & Installation 22-47 Mass Air Flow (MAF) Sensor 22-48 Location 22-48 Removal & Installation 22-48 FUEL.... .....22-48 GASOLINE FUEL INJECTION SYSTEM 22-48 Fuel Filter 22-48 Removal & Installation 22-48 Fuel Injectors 22-48 Removaf & Installation 22-48 Tl Fuel Pum Remov Fuel Syst Precauti! Fuel Tank Drainir Remov Idle Speec Adjustment Relieving Pressure Throttle B Remov Throttle1 Proce 22-50 & Installation 22-50 Service ns... 22-48 22-50 22-50 & Installation 22-50 22-51 22-51 uel System 22-48 dy 22-51 & Installation 22-51 Learn/reset ure....'. 22-51 HEATING & AIR CONDITIONING SYSTEM.! 22-52 Blower Remove Heater Coj RemovE .or 22-52 & Installation 22-52 i, 22-52 & Installation 22-52 PRECAUTIONS.. 22-10 SPECIFICATIONS AND MAINTENANCE CHARTS 22-3 Additional Services^ Additional Services- Brake Spei Camshaft: Capacities Crankshaft Rod Spec Engine anc Identifica Engine Tur Specificai Fluid Speci General En' Maintenam Schedule: Piston and Specificat Tire and Specificai Maintenance ormal 22-9 /laintenance evere '. 22-9 ications 22-7 pecifications 22-5 22-7 .nd Connecting ' ications • 22-5 Vehicle on..., 22-3 -Up ons 22-3 ications 22-3 ine Specificat ons 22-3 and II Service {ing ons. eel ons1. .22-5 .22-7 Torque Specifications 22-6 Valve Specifications 22-4 Wheel Alignment 22-6 STEERING 22-53 Power Steering Gear 22-53 Removal & Installation 22-53 Power Steering Pump 22-53 Bleeding 22-53 Fluid Fill Procedure 22-54 Removal & Installation 22-53 SUSPENSION 22-54 FRONT SUSPENSION 22-54 Control Links 22-54 Removal & Installation 22-54 Lower BallJoint 22-54 Removal & Installation 22-54 Lower Control Arm 22-54 Removal and & lnstallation.22-54 Stabilizer Bar 22-55 Removal & Installation 22-55 Steering Knuckle 22-55 Removal & Installation 22-55 Steering Linkage Outer Tie Rod 22-56 Removal & Installation...- 22-56 Strut & Spring Assembly 22-56 Removal & Installation 22-56 Wheel Bearings 22-57 Adjustment 22-57 Removal & Installation 22-57 REAR SUSPENSION 22-57 Coil Spring 22-57 Removal & Installation 22-57 Knuckle 22-57 Removal & Installation 22-57 Lower Control Arm 22-58 Removal & Installation 22-58 Shock Absorber 22-58 Removal & Installation 22-58 Stabilizer Bar 22-59 Removal & Installation 22-59 Upper Control Arm 22-59 Removal & Installation 22-59 Wheel Bearings 22-59 Adjustment 22-59 Removal & Installation 22-59

CADILLAC SRX 22-3 ENGINE AND VEHICLE IDENTIFICATION Engine Model Year Code© Liters Cu. In. Cyl. Fuel Sys. Engine Type Eng. Mfg. Code® Year 6 170 V6 SFI DOHC GM A 2010 Y 3.0 183 V6 SIDI DOHC GM 2011 ©8th position of VIN © 10th position of VIN 25742_CSRX_C0001 GENERAL ENGINE SPECIFICATIONS All measurements are given, in inches. Engine Fuel Net Net Bore x Com- Oil Displacement Engine System Horsepower Torque @ rpm Stroke pression Pressure Year Model Liters ID/VIN Type @ rpm (ft. Ibs.) (in.) Ratio @ rpm 2010 2011 SRX SRX 2.8 3.0 3.0 6 Y Y SFI SIDI SIDI 300@5500 265@6950 265@6950 295@1850 223@5700 223@5700 3.50x2.95 3.50x3.16 3.50x3.16 10.0:1 11.7:1 11.7:1 20@2000 20@2000 20@2000 25742_CSRX_C0002 ENGINE TUNE-UP SPECIFICATIONS Ignition Idle Engine Spark Plug Timing Fuel Speed Valve Displacement Engine Gap Year Liters IDA/IN (in.) 2010 2011 2.8 3.0 3.0 6 Y Y 0.43 0.43 0.43 (deg.) MT AT © © © © © © Pump (psi) 276-725 PSI 276-725 PSI 276-725 PSI (rpm) Clearance (in.) MT AT Intake Exhaust © © © © © © © © © © © © NS Not Supplied NA Not Applicable © Ignition timing and idle speed are computer controlled and not adjustable. @ Hydraulic lifters 25742_CSRX_C0003

22-4 CADILLAC SRX C) Engine Engine Displacement Engine Oil with Year Model Liters IDA/IN Filter (qt 2010 SF 2011 SF RX 2.8 f 3.0 N RX 3.0 3 6.0 < 6.0 { 6.0 t NOTE: All capacitiesare approximate. Add fluid gradually and ensure a PACITIES Transmission Transfer Drive Fuel Cooling (pts.) Case Axle Tank System .) Auto. Manual (pts.) NA NA 1.5 18.0 NA 1.5 18.0 NA • 1.5 roper fluid level is obtained. (pts.) (gal.) (qts.) 1.4 21.0 12.15 1.4 21.0 12.3 1.4 21.0 12.3 25742_CSRX_C0004 FLUID SPECIFICATIONS Engine II Drive Power Brake Displacement Engine lyjanual Auto. Axle Steering Master Cooling Year Model Liters Oil 2010 2011 SRX SRX 2.8 3.0 3.0 5W-30 5W-30 5W-30 Trans. Trans. Rear Fluid Cylinder System NA [NA II'-NA AW-1 ® © © © © ® • © © © © © © © © DOT: Department Of Transpotation © Dexron IV ©GM part #88861950 © GM Power Steering Fluid ©DOTS or equivalent © Green Engine Coolant 25742_CSRX_C0005 VALVE Engine Seat Face Displacement Engine Angle Angle; Year Liters IDA/IN (deg.) (deg.) 2010 2011 2.8 3.0 3.0 6 Y Y 45.0 45.0 45.0 44.25 44.25 ' 44.25 SPECIFICATIONS Spring Spring Test Installed Pressure Height (Ibs. @ in.) (in.) 61 Ibs. @ 1.378 in. 61 Ibs. @ •1.378 in. 61 Ibs. @ 1.378 in. 1.378 1.3870- 1 .4,45 1.3870- 1.445 Stem-to-Guide Stem Clearance Diameter (in.) (in.) Intake Exhaust Intake Exhaust 0.0010- 0.0026 0.0010- 0.0026 0.0010- 0.0026 0.0014- 0.0030 0.0014- 0.0030 0.0014- 0.0030 0.2344- 0.2352 0.2344- 0.2352 0.2344- 0.2352 0.2341- 0.2.348 0.2341- 0.2348 0.234V 0.2348 25742_CSRX_C0006

CADILLAC SRX 22-5 CAMSHAFT SPECIFICATIONS All measurements in inches unless noted Engine Displacement Engine Journal Brg. Oil Shaft Journal Year Liters Code/VIN Diameter Clearance . End-play Runout Bore 2010 2011 2.8 3.0 3.0 6 Y Y © © © 0.0016- 0.0033 0.0016- 0.0033 0.0016- 0.0033 0.0018- 0.0085 0.0018- 0.0085 0.0018- 0.0085 © © © NS NS NS Lobe Height Intake Exhaust 1 .6687- 1.6805 1.6687- 1.6805 1.6687- 1.6805 1.6715- 1.6833 1.6715- 1.6833 1.6715- 1.6833 ©Journal Diameter 1st: 1.3779-1.3787, Journal Diameter Other: 1.0630-1.0638 © Runout 1st: 1.3779-1.3787, Other. 1.0630-1.0638 25742_CSRX_C0007 CRANKSHAFT AND CONNECTING ROD SPECIFICATIONS All measurements are given in inches. Engine Displacement Engine Year Liters ID/VIN 2010 2011 2.8 3.0 3.0 6 Y Y Crankshaft Connecting Rod Main Brg. Main Brg. Oil Shaft Thrust Journal Oil Side Journal Dia. Clearance End-play on No. Diameter Clearance Clearance 2.6772 2.6772 2.6772 0.0004- 0.0024 0.0004- 0.0024 0.0004- 0.0024 0.0039- 0.0130 0.0039- 0.0130 0.0039- 0.0130 2 2 2 2.2044- 2.2050 2.2044- 2.2050 2.2044- 2.2050 0.0004- 0.0028 0.0004- 0.0028 0.0004- 0.0028 0.0037- 0.0140 0.0037- 0.0140 0.0037- 0.0140 25742_CSRX_C0008 PISTON AND RING SPECIFICATIONS All measurements are alven in inches. Engine Displacement Year Liters Ring Gap Ring Side Clearance Engine Piston Top Bottom Oil Top Bottom Oil ID/VIN Clearance Compression Compression Control Compression Compression Control 2010 2011 2.8 3.0 3.0 6 Y Y 0.0008- 0.0013 0.0008- 0.0013 0.0008- 0.0013 0.0059- 0.0118 0.0059- 0.0118 0.0059- 0.0118 0.0110- 0.0189 0.0110- 0.0189 0.0110- 0.0189 0.0059- 0.0236 0.0059- 0,0236 0.0059- 0.0236 ' 0.0012- 0.0026 0.0012- 0.0026 0.0012- 0.0026 0.0006- 0.0024 0.0006- 0.0024 0.0006- 0.0024 0.0012- 0.0067 0.0012- 0.0067 0.0012- 0.0067 © Measured in cylinder bore 25742_CSRX_C0009

99 c CADILLAC ££" Year 2010 2011 U SRX Engine Disp. Liters 2.8 3.0 3.0 Engine IDA/IN 6 Y Y Cylinder Head Bolts © © © TORQUE All* Main Bearing Bolts © © © B . SPECIFICATIONS ;adings in ft. Ibs. ^od Crankshaft taring Damper $olts Bolts |© © © © (I © © NS Not supplied ©Step 1:22 ft. Ibs. Step 2: Plus 150 degrees Step 1:M8 Bolt: 11 ft. Ibs. Stpn 9- Pln<; 75 dpnrpps Flywheel Manifold Oil Pan Spark Drain Bolts Intake Exhaust Plugs Plug 49 18 49 18 49 18 5 13 18 5 13 18 5 13 18 @ Inner bolts: 15 ft. Ibs. plus 80 degrees Outer bolts: 11 ft. Ibs. plus 110 degrees Side bolts: 22 ft. Ibs. plus 60 degrees ©Step 1:22ft. Ibs. Step 2: Zero Step 3:18 ft. Ibs. Step 4: Plus 110 degrees ©Step 1:74 ft. Ibs. Step 2: plus 150 degrees 25742_CSRX_C0010 WHEEL ALIGNMENT Cast Camber Range Year Model (+/-Deg.j 2010 2011 SRX SRX Front Rear Front Rear 0.75 — 0.75 — [ Preferred Preferred Setting Range Setting Toe-in (Deg.) (+/-Deg.) (Deg.) (Deg.) 4.50 — 4.50 — 0.75 0.75 0.75 0.75 0.60 -1.00 0.60 -1.00 0.20+/-0.20 0.20+/-0.20 0.20+/-0.20 0.20+/-0.20 25742_CSRX_C0011

22-8 CADILLAC SRX MAINTENANCE I AND II SERVICE SCHEDULES SRX When the CHANGE ENGINE OIL light appears, certain services and inspections are required. Required services are described as Maintenance I and Maintenance II. The first service of a vehicle should be Maintenance I, and the second service should be Maintenance II. Alternate between the 2 services thereafter. However, in some cases, Maintenance II may be required more often. Maintenance I: Use Maintenance I if the CHANGE ENGINE OIL light comes on within 10 months since the vehicle was purchased or, if Maintenance II was performed. Maintenance II: Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the CHANGE ENGINE OIL light comes on 10 months or more since the last service, or, if the CHANGE ENGINE OIL light has not come on at all for one year. Service Item Change the engine oil and filter. Reset the oil life system. Visually inspect the vehicle for leaks or damage. A fluid loss in the vehicle system could indicate a problem. Inspect, repair and add fluid to the system if necessary. Inspect the engine air cleaner filter. If necessary, replace the filter. Rotate the tires. Inspect the tire inflation pressures and the tire wear. Visually inspect the brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect the disc brake pads for wear and the rotors for surface condition. Inspect the drum, brake linings for wear or cracks. Inspect other brake parts, including drums, wheel cylinders, calipers, parking brake, etc. Inspect the parking brake adjustment. Inspect engine coolant and windshield washer fluid levels. Add fluid as needed. Inspect the suspension and steering components. Inspect the front and rear suspension and the steering system for damaged, loose or missing parts, or signs of wear. Inspect the power steering lines and the hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Visually inspect the coolant hoses and replace the hoses if they are cracked, swollen or deteriorated. Inspect all pipes, fittings and clamps; replace with GM parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year. Ensure the safety belt reminder light and all the belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from working correctly, repair or replaced, the damaged part. Replace torn or frayed safety belts, refer to Operational and Functional Checks in Seat Belts. Inspect for any opened or broken air bag coverings, and repair or replace as needed. The air bag system does require regular maintenance. Lubricate the body components. Lubricate all key lock cylinders, hood latch assemblies, secondary latches, pivots, spring anchor and release pawl, hood and door hinges, rear folding seats and liftgate hinges. Frequent lubrication may be required when exposed to a corrosive environment, refer to Fluid and Lubricant Recommendations . Applying dielectric silicone grease GM P/N 12345579 (Canadian P/N 1974984) or equivalent on the weatherstrips with a clean cloth. Inspect the wiper blades and replace as necessary. Inspect the throttle and fuel system. Replace the passenger compartment air filter. ' . • ' Inspect exhaust system and heat shields. Maintenance I S V V •/ •/ V •/ — — — •/ — •/ — — s Maintenance II S •s V s s •/ •S -/ V V •/ V V •S s V To reset the CHANGE ENGINE OIL light: 1. Turn the ignition key to the ON/RUN position with the engine OFF. 2. Press and release the stem in the lower center of the instrument cluster until the OIL LIFE message is displayed. 3. Once the alternating OIL LIFE and RESET messages appear, press and hold the stem until several beeps sound. This confirms that the oil life system has been reset to 100 percent. 4. Turn the ignition key to the OFF position. If the CHANGE ENGINE OIL message comes back on when the vehicle is started, the engine oil life system has not been reset. Repeat the procedure. 25742_CSRX_C0014

^^^^^^^^^^^^^^^^^^-^— TIRE AND V OEM Tires Year Model Front 2010 SRX P235/65R18 f} 2011 SRX P235/65R18 ff OEM: Original Equipment Manufacturer PSl: Pounds Per Square Inch © See vehicle tire placard. @ 1 8: standard; 20: optional BRAKl All measun Brake Dis Original Minimum Year Model Thickness Thickness 2010 SRX F NS 1.060 R 0.906 0.846 2011 SRX F NS 1.060 R 0.906 0.846 F: Front R: Rear NS: Information not supplied CADILLAC 99 7 SRX "" / HEEL SPECIFICATIONS Tire Pressures (psi) Wheel Lug Nut Rear Front Rear Size (ft. Ibs.) 235/55R20 © © © 100 235/55R20 © © © 100 25742_CSRX_C0012 i SPECIFICATIONS merits in inches unless noted i Minimum Brake Caliper Pad/Lining Bracket Mounting Max. Thickness Bolts Bolts Runout Front Rear (ft. Ibs.) (ft. Ibs.) 0.002 -NS NS 81 44 0.002 NS NS 81 44 0.002 NS NS 81 44 ; 0.002 NS NS 81 44 2574!LCSRX_C0013

CADILLAC SRX 22-9 ADDITIONAL MAINTENANCE SERVICES - NORMAL SRX TO BE SERVICED Engine coolant Air cleaner filter Automatic transmisison fluid & filter Spark plugs Transfer case fluid Exhaust system & heat shields Cooling system hoses and clamps Fuel system Accessory drive belts Evaporative control system Passenger compartment air filter TYPE OF SERVICE Replace Replace Replace Replace Replace Service/ Inspect Service/ Inspect Inspect Replace Inspect Replace VEHICLE MILEAGE INTERVAL (x1 000) 25 •/ S •/ 50 s •/ s •/ •/ 75 •/ S • •/ 100 ^ •/ s s s •/ s V 125 V •/ •/ 150 Y S V S •/ S S •/ 25742_CSRX_C0015 ADDITIONAL MAINTENANCE SERVICES - SEVERE SRX TO BE SERVICED Engine coolant Air cleaner filter Automatic transaxle fluid Spark plugs Transfer case fluid Exhaust system & heat shields Cooling system hoses and clamps Fuel system Accessory drive belt(s) Evaporative control system Passenger compartment air cleaner TYPE OF SERVICE Replace Replace Replace Replace Replace Inspect Inspect Inspect Replace Inspect Replace VEHICLE MILEAGE INTERVAL (xlOOO) 25 •/ S •/ •s •/ 50 •/ S •/ V •/ •/ •/ s 75 S S -/ S •/ 100 •/ •/ •/ •/ s s •/ s •/ 125 V V •/ S •/ 150 •/ V V s •/ s s •s •/ •s 25742_CSRX_C0016

22-10 CADILLAC SRX PRECAUTIONS Before servicing any vehicle, please be sure to read all of the following precautions, which deal with personal safety, prevention of component damage, and important points to take into consideration when servicing a motor vehicle: • Never open, service or drain the radiator, or cooling system when the engine is hot; serious burns can occur from the steam and hot coolant. • Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well-ventilated area. Do not allow fuel spray or vapors to come in contact with a spark, open flame, or excessive heat (a hot drop light, for example). Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion. Refer to the additional fuel system precautions later in this section. • Fuel injection systems often remain pressurized, even after the engine has been turned OFF. The fuel system pressure must, be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury. • Brake fluid often contains polyglycol ethers and polyglycols. Avoid contact with the eyes and wash your hands thoroughly after handling brake fluid. If you do get brake fluid in your eyes, flush your eyes with clean, running water for 15 minutes. If eye irritation persists, or if you have taken GENERAL INFORMATION PRECAUTIONS • Certain components within the ABS ' system are not intended to be serviced or repaired individually. • Do not use rubber hoses or other parts not specifically specified for and ABS system. When using repair kits, replace all parts included in the kit. Partial or incorrect repair may lead to functional problems and require the replacement of components. • Lubricate rubber parts with clean, fresh brake fluid to ease assembly. Do not use shop air to clean parts; damage to rubber components may result. • Use only DOT 3 brake fluid from an unopened container. • If any hydraulic component or line is :e n brake fluid in] medical assis' • The EP/^ with used enc of skin disord should make! exposure to u gloves slioulc Wash your ha skin areas as sure to used e waterless nan • All new with an air ba a Supplement Supplemental' tern. The syst performing se components, panel compor Failure to dures could re deployment, unnecessary • Always v working with, When carrying a sure the bag away from yoi deployed air face the bag a from the surfa motion of the deployed. Refe system precai • Clean, h sealed contair rnally, IMMEDIATELY seek nee. warns that prolonged contact ne oil may cause a number rs, including cancer. You very effort to minimize your ed engine oil. Protective be worn when changing oil. ds and any other exposed oon as possible after expo- igine oil. Soap and water, or cleaner should be used, ehicles are now equipped system, often referred to as Restraint System (SRS) or nflatable Restraint (SIR) sys- must be disabled before vice on or around system :eeririg column, instrument fits, wiring and sensors. N safety and disabling proce- sult in accidental air bag personal injury and /stem repairs, ear safety goggles when r around, the air bag system. non-deployed air bag, be trim cover are pointed • body. When placing anon- ig on a work surface, always d trim cover upward, away e. This will reduce the nodule if it is accidentally 'to the additional air bag ions later in this section. ;h quality brake fluid from a r is essential to the safe and aid proper operation of the brake system. You should always buy the correct type of brake fluid' for your vehicle. If the brake fluid becomes contaminated, completely flush the system with new fluid. Never reuse any brake fluid. Any brake fluid that is removed from the system should be discarded. Also,, do not allow any brake fluid to come in contact with a painted surface; it will damage the paint. • Never operate the engine without the proper amount and type of engine oil; doing so WILL result in severe engine damage. • Timing belt maintenance is extremely important. Many models utilize an interference-type, non-freewheeling engine. If the timing belt breaks, the valves in the cylinder head may strike the pistons, caus- ing potentially serious (also time-consum- ing and expensive) engine damage. Refer to the maintenance interval charts for therec- ommended replacement interval for the tim- • ing belt, and to the timing belt section for belt replacement and inspection. • Disconnecting the negative battery cable on some vehicles may interfere with the functions of the on-board computer system^) and may require the computer to undergo a relearning process once the negative battery cable is reconnected. • When servicing drum brakes, only dis- assemble and assemble one side at a time, leaving the remaining side intact for refer- ence. • .Only an MVAC-trained, EPA-certified automotive technician should service the air conditioning system or its components. ANTI-LOCK BRAKE SYSTEM (A^S) removed or re bleed the entiij • A clean r clean the resei before removing amount of dirt fice and impai repairs oughly cleane to clean comp components to substance includes used • TheAntH laced, it may be necessary to system. pair area is essential. Always /oir and cap thoroughly the cap. The slightest n the fluid may plug an ori- •the system function. Perform after components have been thor- use only denatured alcohol nents. Do not allow ABS come into contact with any mineral oil; this ;hop rags. .ock control unit is a micro- processor simj ar to other computer units in the vehicle. Erj ;ure that the ignition switch is OFF before emoving or installing controller harnessi s. Avoid static electricity dis- charge at or ne.br the controller. con aming • If any arc welding is to be done on the vehicle, the control unit should be unplugged before welding operations begin. SPEED SENSORS REMOVAL & INSTALLATION Front See Figure 1. 1. Before servicing the vehicle, refer to the Precautions Section. 2. Raise and support the vehicle. 3. Remove the tire and wheel assembly. 4. Remove the wheel speed sensor bolt. 5. Clean the wheel speed sensor mounting area on the suspension knuckle of any accumulated dirt and debris.

2010 Cadillac SRX Service & Repair Manual

You're Reading a Preview

Recently Viewed