Landini Rex 60, 65, 70, 80, 90 100 V GE Tractor Full Service & Repair Manual

REX 60-65-70-80 V 60-70-80-90-100 GE-F-L-GT Training manual P/N° 3659961M2

CONTENTS Chap. 1 INTRODUCTION Chap. 2 ENGINE Chap. 3 CLUTCH Chap. 4 STANDARD TRANSMISSION Cap. 5 4WD FRONT AXLE Chap. 6 POWER TAKE-OFF Chap. 7 LOW PRESSURE HYDRAULIC CIRCUIT Chap. 8 HIGH PRESSURE STANDARD HYDRAULIC CIRCUIT Chap.9 MECHANICAL POWER LIFT Chap.10 ELECTRONIC POWER LIFT Chap.11 ELECTRICAL SYSTEM Chap.12 AIR CONDITIONING SYSTEM Chap.13 SPECIAL TOOLS CONTENTS

PRE-SALE SERVICE May 2003 42042 FABBRICO (RE) ITALY PREFACE This manual contains the technical specifications, mechanical, hydraulic layouts and wiring diagrams, plus instructions on how to operate and adjust Landini's Rex Orchard 60-70-80-90-100 and Rex Vineyard 60V-65V-75V-80V series tractors. It does not contain all the necessary information as it is completed with the theoretical and practical explanations and theoretical descriptions given by the instructors during the training courses. This information is therefore dedicated to the persons who frequent training courses at the Landini training center. NOTE : The descriptions and technical specifications in this manual are strictly not binding. Landini therefore reserves the right to modify the components and accessories for technical or commercial reasons without being obliged to update this manual each time.

INTRODUCTION 1 - 1 CHAP.1 CONTENTS Sect. 1 Reading the manual. ................................................................. 1-3 1-1 Introduction .................................................................... 1-4 1-2 Structure of the manual .................................................. 1-4 Sect. 2 Tractor identification and technical specifications. ............... 1-5 2-1 Tractor identification ...................................................... 1-6 2-2 Weights and dimensions ............................................... 1-7 2-3 Engine specifications ................................................... 1-13 2-4 Clutch specifications .................................................... 1-16 2-5 Transmission specifications ........................................ 1-16 2-6 Power take-off specifications ....................................... 1-23 2-7 2 WD axle .................................................................... 1-24 2-8 4 WD front axle specifications ..................................... 1-25 2-9 Hydraulic circuit specifications .................................... 1-26 Sect. 3 Working in safety. ................................................................... 1-29 3-1 Essential rules for accident prevention ........................ 1-30 3-2 Danger decals ............................................................. 1-36 3-3 Replacing tractor parts ................................................ 1-39 3-4 Safe use of the tractor .................................................. 1-39 Sect. 4 Pre-delivery inspections and maintenance. .......................... 1-41 4-1 General information ..................................................... 1-42 4-2 Inspections before delivery .......................................... 1-42 4-3 Routine maintenance guide ......................................... 1-43

INTRODUCTION 1 - 2 CHAP.1 Sect. 5 Conversion tables. .................................................................. 1-45 5-1 Length ......................................................................... 1-46 5-2 Area ............................................................................. 1-49 5-3 Volume ........................................................................ 1-50 5-4 Weight ......................................................................... 1-53 5-5 Pressure ...................................................................... 1-55 5-6 Moment of rotation ....................................................... 1-57 5-7 Temperature ................................................................ 1-59 Sect. 6 Sealants. .................................................................................. 1-61 6-1 Types of Loctite sealants ............................................. 1-62 6-2 Practical advice ........................................................... 1-63 Sect. 7 Driving torques. ....................................................................... 1-65 Sect. 8 General assembly instructions. ............................................. 1-67 8-1 Seals ........................................................................... 1-68 8-2 O-rings ........................................................................ 1-69 8-3 Bearings ...................................................................... 1-70

INTRODUCTION 1 - 3 CONTENTS Sect.1 Reading the manual 1-1 Introduction .................................................................... 1-4 1-2 Structure of the manual .................................................. 1-4 CHAP. 1 Reading the manual

INTRODUCTION 1 - 4 Sect.1 - Reading the manual 1-1 Introduction The purpose of this training manual is to provide clear instructions on how to repair and adjust Rex Orchard and Vineyard series tractors. The manual is for the chief foreman since it does not describe the demounting, remounting and adju- stment operations in detail and for all assemblies, merely those that require particular expertise or re- commendations. Before reading the manual, it is essential to read sect.3: WORKING IN SAFETY in order to prevent errors or mistakes that could jeopardize the safety of the technicians in the workshop. The information in this manual was up to date at the time of publication. Landini reserves the right to make modifications without being obliged to give notice. Please contact your area dealer or the importer if discrepancies are discovered or for any other requi- rement. 1-2 Structure of the manual The manual is divided into chapters (chap.) and each chapter into sections (sect.). Page numbering begins with 1 for each chapter with the number of the chapter itself alongside. Example: 6-7 indicates page 7 of chapter 6. Numbering of the figures also begins with 1 in each chapter with the chapter number alongside. Example: Fig. 9-6, indicates figure 9 of chapter 6.

INTRODUCTION 1 - 5 CONTENTS Sect.2 Tractor identification and technical specifications 2-1 Tractor identification ...................................................... 1-6 2-2 Weights and dimensions ............................................... 1-7 2-3 Engine specifications ................................................... 1-13 2-4 Clutch specifications .................................................... 1-16 2-5 Transmission specifications ........................................ 1-16 2-6 Power take-off specifications ....................................... 1-23 2-7 2 WD axle .................................................................... 1-24 2-8 4 WD front axle specifications ..................................... 1-25 2-9 Hydraulic circuit specifications .................................... 1-26 Tractor identification and technical specifications CHAP.1

INTRODUCTION 1 - 6 Sect.2-Tractor identification and technical specifications 2-1 Tractor identification The tractor is identified by a serial number stamped on the rear part of the transmission housing and on the bonnet. The engine also has its own serial number stamped on the engine block. To ensure a quick and efficient service when orde- ring spare parts or asking for technical specifications or other information, always state the chassis and engine serial number. Chassis serial number ........................................... Engine serial number ............................................. Cab serial number .................................................. Type of tractor ........................................................ Owner / Operator ................................................... Dealer's or Agent's address ................................... ............................................................................... Delivery date .......................................................... Warranty expiry date ............................................. Fig.5-1 Fig.4-1 Fig.3-1 Fig.2-1 Fig.1-1

INTRODUCTION 1 - 7 F C B A D E G H I 60 GE 60 F 60 L 2 WD 4 WD 2 WD 4 WD 2 WD 4 WD 9.00-10 9.0/75-16 7.50-15 8.25-16 7.50-15 280/70-18 14.9 LR 20 13.6/12-24 13.6-24 13.6-28 2250 2380 2180 2380 2260 2410 — — 2680 — 2760 — 1231 1250 1250 1375 1430 1430 2350 2220 2240 2350 2350 2370 1940 1900 1940 1900 1940 1900 3778 3778 3778 360 360 360 1330 1330 1490 1680 1680 1830 See track See track See track tables tables tables General specifications With tyres - front - rear Weights - In running order, with front and rear ballast and with safety frame .................... Kg - Ditto with cab ........................................... Kg Dimensions A- Height at bonnet ................................... mm B - Height at sttering wheel ....................... mm C - Height at cab ........................................ mm Height at safety frame .......................... mm D - Wheelbase ........................................... mm E- Max. length with front ballast and links .. mm F- Ground clearance (drawbar) ................ mm min. G - Width ...................................... mm max. H - Front track ............................................ mm I - Rear track ............................................. mm { Tractor identification and technical specifications 2-2 Weights and dimensions Fig.6-1

Landini Rex 60, 65, 70, 80, 90 100 V GE Tractor Full Service & Repair Manual

You're Reading a Preview

Recently Viewed