Landini Series 60, 5860, 6860, 7860, 8860 Evolution Tractor Full Service & Repair Manual

60 Series 5860-7860 / 6860-8860 Evolution Training Manual P/N° 3667270M1

CONTENTS Chap. 1 INTRODUCTION Chap. 2 ENGINE Chap. 3 CLUTCH Chap. 4 TRANSMISSION Chap. 5 4WD FRONT AXLE Chap. 6 POWER TAKE-OFF Chap. 7 LOW PRESSURE HYDRAULIC CIRCUIT Chap. 8 HIGH PRESSURE HYDRAULIC CIRCUIT Chap. 9 MECHANICAL POWER LIFT Chap. 10 ELECTRICAL SYSTEM Chap. 11 SPECIAL TOOLS CONTENTS

PRE-SALE SERVICE December 2002 42042 FABBRICO (RE) ITALY PREFACE This manual includes all specifications, mechanical, hydraulic and electrical diagrams as well as descriptions of operation and adjustments of 60 Series tractors. The manual is not necessarily comprehensive of all information, as it has to be completed by theoretical and practical explanations given by trainers during training courses. This information is therefore exclusively ai- med to persons attending courses at Landini Training Center. NOTE: Descriptions and specifications contained in this manual are not committing. Landini reserves the right to change organs and accessories owing to technical or commercial requirements without each time updating this manual.

INTRODUCTION 1 - 1 CHAP.1 INDEX Sect. 1 Reading the manual. ............................................................... 1-3 1-1 Introduction ................................................................... 1-4 1-2 Structure of the manual ................................................ 1-4 Sect. 2 Tractor identification and technical specifications. ............ 1-5 2-1 Tractor identification ..................................................... 1-6 2-2 Weights and dimensions .............................................. 1-7 2-3 Engine specifications ................................................... 1-9 2-4 Clutch specifications ................................................. 1-11 2-5 Transmission specifications ...................................... 1-11 2-6 Power take-off specifications .................................... 1-16 2-7 2 WD axle .................................................................. 1-17 2-8 4 WD front axle specifications .................................. 1-18 2-9 Hydraulic circuit specifications ................................. 1-19 Sect. 3 Working in safety................................................................... 1-21 3-1 Essential rules for accident prevention ..................... 1-22 3-2 Danger decals ........................................................... 1-28 3-3 Replacing tractor parts .............................................. 1-34 3-4 Safe use of the tractor ............................................... 1-34 Sect. 4 Pre-delivery inspections and maintenance. ..................... 1-37 4-1 General information ................................................... 1-38 4-2 Inspections before delivery ....................................... 1-38 4-3 Routine maintenance guide ...................................... 1-39

INTRODUCTION 1 - 2 CHAP.1 Sect. 5 Conversion tables. ................................................................ 1-41 5-1 Length ........................................................................ 1-42 5-2 Area ........................................................................... 1-45 5-3 Volume ....................................................................... 1-46 5-4 Weight ........................................................................ 1-49 5-5 Pressure .................................................................... 1-51 5-6 Moment of rotation .................................................... 1-53 5-7 Temperature .............................................................. 1-55 Sect. 6 Sealants. ................................................................................ 1-57 Sect. 7 Table of bolt driving torques. .............................................. 1-59 Sect. 8 General assembly instructions. .......................................... 1-61 8-1 Seals .......................................................................... 1-62 8-2 O-rings ....................................................................... 1-63 8-3 Bearings .................................................................... 1-64

INTRODUCTION 1 - 3 INDEX Sect.1 Reading the manual 1-1 Introduction ................................................................... 1-4 1-2 Structure of the manual ................................................ 1-4 CHAP. 1 Reading the manual

INTRODUCTION 1 - 4 1-1 Introduction The purpose of this training manual is to provide clear instructions on how to repair 60 Series tractors. The manual is for the chief foreman since it does not describe the demounting, remounting and adjustment operations in detail and for all assemblies, merely those that require particular expertise or recommenda- tions. Before reading the manual, it is essential to read sect.3: WORKING IN SAFETY in order to prevent errors or mistakes that could jeopardize the safety of the technicians in the workshop. The information in this manual was up to date at the time of publication. Landini reserves the right to make modifications without being obliged to give notice. Please contact your area dealer or the importer if di- screpancies are discovered or for any other require- ment. 1-2 Structure of the manual The manual is divided into chapters (chap.) and each chapter into sections (sect.). Page numbering begins with 1 for each chapter with the number of the chapter itself alongside. Example: 5-7 indicates page 7 of chapter 5. Numbering of the figures also begins with 1 in each chapter with the chapter number alongside. Example: Fig. 73-5, indicates figure 73 of chapter 5. The tools required for all the demounting, remounting and adjusting operations are listed at the end of each important chapter or section. However, not all the tools given at the end of the chapter or section are men- tioned in the text, just those considered essential to demount, remount and adjust the unit in question in the correct way. Chapter 11 contains the constructional drawings of all the tools indicated in the various chapters or sections so that dealers can make all those considered neces- sary for their workshops. Sect.1 - Reading the manual

INTRODUCTION 1 - 5 INDEX Sect.2 Tractor identification and technical specifications 2-1 Tractor identification ..................................................... 1-6 2-2 Weights and dimensions .............................................. 1-7 2-3 Engine specifications ................................................... 1-9 2-4 Clutch specifications ................................................. 1-11 2-5 Transmission specifications ...................................... 1-11 2-6 Power take-off specifications .................................... 1-16 2-7 2 WD axle .................................................................. 1-17 2-8 4 WD front axle specifications .................................. 1-18 2-9 Hydraulic circuit specifications ................................. 1-19 Tractor identification and technical specifications CHAP.1

INTRODUCTION 1 - 6 Fig.2-1 Fig.1-1 Fig.3-1 Fig.4-1 5860. Engine type and serial number. 6860 - 7860. Chassis type and serial number. Chassis type and serial number (on board). Chassis type and serial number - Plate on the bonnet. 2-1 Tractor identification The tractor is identified by a serial number stamped on the rear part of the transmission housing and on the bonnet. The engine also has its own serial number stamped on the engine block. To ensure a quick and efficient service when ordering spare parts or asking for technical specifications or other information, always state the chassis and engine serial number. Chassis serial number ............................................. Engine serial number .............................................. Type of tractor ........................................................ Owner / Operator ..................................................... Dealer's or Agent's address ..................................... ............................................................................... Delivery date ........................................................... Warranty expiry date ............................................... Sect.2-Tractor identification and technical specifications

INTRODUCTION 1 - 7 2-2 Weights and dimensions Fig.5-1 General specifications With tyres - front - rear Weights - In running order, with front and rear ballast and safety frame .................................................... Kg - As above, with cast iron rear wheel discs ............. Kg Dimensions C - Height at safety frame ............................................ mm. D - Wheelbase ............................................................. mm. E - Max. length with front ballast and lift links .............. mm. F - Ground clearance (under front axle) ..................... mm. G - Width ...................................................................... mm. H - Front track ............................................................... mm. I - Rear track ............................................................... mm. 5860 2 WD 4 WD 7.50-16 12.4-24 14.9R28 14.9R28 2700 2980 - - 2410 2410 2126 2109 3837 3837 480 350 min. 1678 min. 1678 max. 2278 max. 2278 See track tables D E H F C I Tractor identification and technical specifications

You're Reading a Preview

Landini Series 60, 5860, 6860, 7860, 8860 Evolution Tractor Full Service & Repair Manual

Description

Reviews

Q&A

Recently Viewed