Kubota B1700/B2100/B2400 Tractors OEM Service & Repair Manual

SAFETY INSTRUCTIONS 91700-B2100-S2400 WSM,11770 A SAFETY FIRST This symbol, the industry's "Safety Alert Symbol", is used throughout this manual and decals on the machine itselfto warn ofthe possibility of personal injury. Read these instructions carefully. It is essential that you read the instructions and safety regulations before you attempt to repair or use this unit. A DANGER : Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. A WARNING : Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. A CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury . • IMPORTANT : Indicates that equipment or property damage could result if instructions are not followed . • NOTE : Gives helpful information. SAFETY SERVICING AND REPAIRING (1) Before working on the machine: • Park the machine on a firm and level ground, and set the parking brake. • Lower the implement or mower to the ground. • Stop the engine, and remove the key. • Disconnect the battery's ground cable. • Clean the work area and machine. (2) Do not work on the machine while under the influence of alcohol, medication, or other substances or while fatigued. (3) Do not wear a necktie, scarf, necklace, loose or bulky clothing when you work near machine tools or moving parts. (4) Use tools appropriate to the work. Makeshift tools, parts, and procedures will not make good repairs. (5) When servicing is performed together by two or more persons, take care to perform all work safely. (6) Do not work under the machine that is supported solely by a jack. Always support the machine by safety stands.

81700·82100·82400 WSM.11770 SAFETY INSTRUCTIONS (7) If the engine must be running to do same work, make sure the area is well ventilated. Never run the engine in a closed area. The exhaust gas contains poisonous carbon monoxide. (8) Do not touch the rotating or hot parts while the engine is running. (9) Fuel is extremely flammable and explosive under certain conditions. Do not smoke or allow flames or sparks in your working area. (10) To avoid sparks from an accidental short circuit, always disconnect the battery's ground cable first and connect it last. (11) Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, clothing and cause blindness if splashed into eyes. Keep electrolyte away from eyes, hands and clothing. If you spill electrolyte on yourself, flush with water, and get medical attention immediately. (12) Battery gas can explode. Keep sparks and open flame away from the top of battery, especially when charging the battery. (13) Never remove the radiator cap while the engine is running, or immediately after stopping. Otherwise, hot water will spout out from radiator. Wait for more than ten minutes to cool the radiator, before removing the cap. (14) Escaping fluid (fuel or hydraulic oil) under pressure can penetrate the skin causing serious injury. Relieve pressure before disconnecting hydraulic or fuel lines. Tighten all connections before applying pressure. (15) Do not start the engine by shorting across starter terminals. (16) Unauthorized modifications to the machine may impair the function and I or safety and affect machine life. (17) Do not alter or remove any part of machine safety system. (18) Keep a first aid kit and fire extinguisher handy at all times. (19) Be sure to chock the wheels to prevent accident during servicing the machine. 2

SAFETY INSTRUCTIONS 81700·82100·82400 WSM,11770 SAFETY DECALS • The following safety decals are installed on the machine. If a decal becomes damaged, illegible or is not on the machine. replace it. The decal part number is listed in the parts list. (1) Part No. TA040-4965-2 (2) Part No. TA040-4959-3 (5) Part No. 6C050-4724-1 (4) Part No. TA040-4935-1 (3) Part No. 6C040-4741-1 No fire r@ (6) Part No. TA04O-4958-1 [HSTtype] Do not touch hot surface like muffler, etc. B177F001 3

81700'82100'B2400 WSM,11770 SAFETY INSTRUCTIONS (7) Part No. TA040-4932-2 (8) Part No. 32751-4958-1 Stay clear of engine fan and fan belt. (9) Part No. 6C040-4742-1 ACAUTION (10) Part No. 6C040-5559-1 DANGER EXPLOSIVE GASES Ci~rttIS. flamss Of sparks cIJuld CklJe battery to explode. Always sbi1lkl eyes and face from bltwy, Do not chlfge Of ~se booster ~ or adjust post tOnnerttiona without proper instruttlon and ulimAg. KEEP VENT CAPS TIGHT AND LEVEL POISON CAUSES SEVERE BURNS Contlins sulfUfie Kid. AI/oid contacl witfl.kin, &ye$ Of clothing. In event of accident Hush wilh walt!" and call a physicilll immediat~y. KEEP OUT OF REACH OF CHILDREN CARE OF DANGER, WARNING AND CAUTION LABELS 1. Keep danger, warning and caution labels clean and free from obstructing material. 2. Clean danger. warning and caution labels with soap and water, dry with a soft cloth. 3. Replace damaged or missing danger. warning and caution labels with new labels from your local KUBOTA dealer. 4. If a component with danger, warning and caution label (s) affixed is replaced with new part, make sure new label (5) is (are) attached in the same location Is) as the replaced component. 5. Mount new danger, warning and caution labels by applying on a clean dry surface and pressing any bubbles to outside edge. B177F002 4

SPECIFICATIONS 81700-82100-82400 WSM,11770 SPECIFICATIONS Model 81700 HSD 82100 HSD 82400 HSD PTO power 9.7 kW (13.0 HP)" 12.0 kW (16.0 HP)" 13.4 kW (18.0 HP)" Maker KUBOTA Model 0905-010 01005-010 01105-010 Type Indirect Injection. Vertical, water-cooled, 4-cycle diesel Number of cylinders 3 Bore and stroke 72 x 73.6 mm (2.83 x 2.90 in.) 76 x 73.6 mm (2.99 x 2.90 in.) 78 x 78.4 mm (3.07 x 3.09 in.) Total displacement 898 cm 3 (54.8 cu.in.) 1001 cm 3 (61.1 cu.in.) 1123 cm 3 (68.5 cu.in.) (IJ Engine gross power 12.7 kW(17.0 HP) 15.7 kW (21.0 HP) 17.9 kW(24.0 HP) c 0> Rated revolution c 43.3 rfs (2600 rpm) lJJ Maximum torque 51 N-m (38 ft-Ibs) 59 N·m (44 ft-Ibs) 67 N-m (50 ft-Ibs) Battery 12V, RC: 71 min,CCA: 390A(12V,RC: 79 min,CCA: 433A) Starting system Electric starting with cell starter 12V, 1.0 kW Lubricating system Forced lubrication by trochoidal pump Cooling system Pressurized radiator, forced circulation with water pum p Fuel Oiesel fuel No.2-0 [above-10°C (14°F)), Oiesel fuel No.1 [below-10°C (14°F)] Fuel tank 24/(6.3 U.S.gals, 5.3Imp.gal) <II EnRine crankcase 3.01 (3.2 U.S.qts, 2.6Imp.qts) (IJ (WI h filter) .;; 'v Engine coolant 3.41 (3.6 U.S.qts, 2.6Imp.qts) '" Q. '" u Transmission case 12.01 (3.17 U.S.gals, 12.4Imp.gals) Frontaxle case 3.71 (3.9 U.S.qts, 3.3 Imp.qts) Overall length (without 3P) 2280 mm (89.8 in.) 2300 mm (90.6 in.) 2330 mm (91.7 in.) Overall width (min. tread) 989 mm (38.9 in.) 1077 mm (42.4 in.) 1175 mm (463 in.) <II Overall height (with ROPS) 1915 mm (75.4 in.) 1940 mm (76.4 in.) 1965 mm (77.4 in.) c 0 Overall height (top of seat) 1293 mm (50.9 in.) 1318 mm (51.9 in.) 1343 mm (52.9 in.) ;:;; c Wheelbase 1500 mm (59.0 in.) (IJ E 3 Min. ground clearance 295 mm (11.6 in.) 305 mm (12.0 in.) 325 mm (12.8 in.) Front 835 mm (32.9 in.) 835 mm (32.9 in.) 835 mm (32.9 in.) Treads 778 to 948 mm 836to 1006 mm 890 to 1064 mm Rear (30.6 to 37.3 in.) (32.9to 39.6 in.) (35.0 to 41.9 in) weight (with ROPS) 635 kg (1402 Ibs) 647 kg (1428Ibs) 662kg (1461Ibs) Clutch Ory single plate Front 6-12 6·12 7-12 E Tires (IJ Rear 8.3-16 9.5-16 11.2-16 .. .... Steering Integral type power steering >. .... 0> Transmission Main-hydrostatic transmission, High·Low gear shift (2 forward, 2 reverse) c - ill Brake Wet disk :> '" f.: Min. turnin~ radius (with brake 2.1 m (6.9 feet) E Hydraulic control system Position Control (IJ Pump capacity 221/min (5.8 gals/min) .. .... >. .... Three point hitch SAE Category I .~ ::; At lift pOints 580 kg (1280 Ibs) ~ Max. lift -0 >. force 24 in, behind 460 kg (1015Ibs) I lift points Rear-PTO SAE 1·3IB, 6 splines .t: '" Revolution 543 rpm at 2600 engine rpm J;;: '" 0 Mid-PTO USA NO.5 (KUBOTA 10-tooth) involute spline t- o.. Revolution 2537 rpm at 2600 engine rpm Note: .. Manufacture's estimate the company reserves the rightto change the specifications without notice. 5

B1700·B2100·B2400 WSM,11770 SPECIFICATIONS Model 817000 821000 PTO power 10.7kW(14.0HP)* 12.7 kW (17.0 HP)* I Maker KUBOTA Model D905-D10 Dl005-Dl0 Type Indirect Injection. Vertical, water-cooled, 4-cycle diesel i Number of cylinders 3 Bore and stroke 72 x 73.6 mm (2.83 x 2.90 in.) 76 x 73.6 mm (2.99 x 2.90 in.) Total displacement 898 cm 3 (54.8 cu.in.) 1001 cm 3 (61.1 cu.in.) i (l) Engine gross power 12.7 kW (17.0 HP) 15.7kW(21.0HP) c 0> c Rated revolution 43.3 r/s (2600 rpm) w Maximum torque 51 N'm (38 ft-Ibs) 59 N'm (44 ft-Ibs) i Battery 12V, RC: 71 min,CCA: 390A(12V, RC: 79 min,CCA: 433A) Starting system Electric starting with cell starter 12V, 1.0 kW I Lubricating system Forced lubrication by trochoidal pump , Cooling system Pressurized radiator, forced circulation with water pump I Fuel Diesel fuel No.2-D [above-10°C (14°F)1. Diesel fuel No.1 [below-lO°C (14°F)] Fuel tank 241 (63 U.S.gals, 5.3 Imp.gal) '" En~ine crankcase 3.01 (3.2 U.S.qts, 2.6 Imp.qts) (l) (WI h filter) '';::; 'v '" Engine coolant 3.41 (3.6 U.S.qts, 2.6Imp.qts) 0- '" v Transmission case 11.01 (2.90 U.S.gals, 2.4Imp.gals) Front axle case 3.7 i (3.9 U.S.qts, 3.3Imp.qts) Overall length (without 3?) 2280 mm (89.8 in.) 2300 mm (90.6 in.) Overall width (min. tread) 989 mm (38.9 in.) 1077 mm (42.4 in.) '" Overall height (with ROPS) 1915 mm (75.4 in.) 1940 mm (76.4 in.) c: Overall height (top of seat) 1293 mm (50.9 in) 0 1318mm(51.9in.) .;;; c Wheelbase 1500 mm (59.0 in.) (l) E Ci Min. ground clearance 295 mm (11.6 in.) 305 mm (12.0 in.) i Front 835 mm (32.9 in.) 835 mm (32.9 in.) I Treads 778 to 948 mm 836to 1006 mm Rear (306 to 37.3 in.) (32.9 to 39.6 in.) , Weight (with ROPS) 625 kg (1380 Ibs) 637 kg (1406Ibs) Clutch Dry single plate Front 6-12 6-12 E Tires (l) Rear 8.3-16 9.5-16 ..... '" Steering Integral type power steering >. '" Ol Transmission Main-hydrostatic transmission, High-Low gear shift (2 forward, 2 reverse) c - (l) Brake Wet disk > '" i::- Min. turnin~ radius (with brake 2.1 m (6.9 feet) E Hydraulic control system Position Control (l) Pump capacity 221/min (5.8 gals/min) ..... '" >. VI Three point hitch SAE Category I .~ :::J At lift points 580 kg (1280 Ibs) ~ Max. lift 'U >. force 24 in, behind 460 kg (1015Ibs) I lift points Rear-PTO SAE 1-3/8,6 splines .;: '" Revolution 540 rpm at 2600 engine rpm {i 0 I- Mid-PTO USA No.5 (KUBOTA 10-tooth) involute spline 0.. Revolution 2531 rpm at 2600 engine rpm Note: ., Manufacture's estimate the company reserves the right to change the specifications without notice. 6 /

SPECIFICATIONS S1700·S2100·S2400 WSM, 1 1770 TRAVELING SPEEDS [HSTType] (At rated engine rpm) Model B1700 B2100 B2400 Tire size (Rear) S.3-16 9.5-16 11.2-16 Hi-Logear shift lever km/h mph km/h mph km/h mph Forward Low Oto 5.0 Oto 3.1 Oto 5.3 Oto 3.3 Oto 5.6 Oto 3.5 High Oto 12.3 Oto 7.7 Oto 13.2 OtoS.2 Oto13.9 OtoS.7 Reverse Low Oto 5.0 Oto 3.1 Oto 5.3 Oto 3.3 Oto 5.6 Oto3.5 High oto 12.3 o to 7.7 o to 13.2 OtoS.2 Oto13.9 OtoS.7 [Manual Transmission Type] (At rated engine rpm) Model B1700 B2100 Tire size (Rear) S.3-16 9.5-16 Hi-Lo gear shift lever Main gear shift lever km/h mph km/h mph Forward 1 f-- 2 f-- 3 Low 1 1.0 0.6 1.0 0.6 2 1.7 I 1.1 1.S 1.1 3 3.1 1.9 3.3 2.1 4 f-- 5 High f-- 6 1 4.1 2.6 4.4 2.S 2 7.3 4.6 7.S 4.9 3 13.2 S.3 14.1 S.S Reverse 1 Low R 1.2 O.S 1.3 O.S 2 High R 5.2 3.2 5.5 3.5 The company reserves the right to change the specifications without notice. 7

81700·82100·82400 WSM, 11770 DIMENSIONS DIMENSION Maximum dimension is shown against farm tire variation. Unit: mm (in.) 81700 82100 B2400 1500 (59.0) B1700 2280 (89.8) 82100 2300 (90.6) 82400 2330 (91.7) 000 000 r--.-'¢ .-NN eo eo eo ~~~ LCi<cir-: t:::.t:::.t:::. 1.001.0 .-'¢<O aleDO) .-.- .- 000 g~~ .-NN eo eo eo B177F003 8

CONTENTS [1] FEATURES ....................................................................................................... G-1 [2] TRACTOR IDENTIFICATION ............................................................................ G-2 [3] GENERAL PRECAUTIONS ................................................................................ G-3 [4] HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING .............. G-4 [5] LUBRICANTS, FUEL AND COOLING WATER ..................................................G-8 [6] TIGHTENING TORQUES (GENERAL USE SCREWS, BOLTS AND NUTS) ........ G-8 [7] MAINTENANCE CHECK LIST ......................................................................... G-10 [8] CHECK AND MAINTENANCE ........................................................................ G-11 (1) DailyCheck ............................................................................................. G-11 (2) Check Points of Initial 50 Hours ............................................................... G-12 (3) Check Points of Every 50 Hours ............................................................... G-14 (4) Check Poi nts of Every 100 Hours ............................................................. G-18 (5) Check Point of Every 200 Hours ...............................................................G-20 (6) Check Point of Every 300 Hours ............................................................... G-22 (7) Check Point of Every 400 Hours ............................................................... G-22 (8) Check Point of Every 800 Hours ............................................................... G-22 (9) Check Point of Every 1 Year .................................................................... G-23 (10) Check Poi nt of Every 2 Years ................................................................... G-23 (11) Others .....................................................................................................G-25 [9] SPECIAL TOOLS ............................................................................................ G-26 (1) Special Tools for Engine ..........................................................................G-26 (2) Special Tools for Tractor ......................................................................... G-30 [10] TIRES .............................................................................................................G-33 (1) Type of Tire ............................................................................................. G-33 (2) Tread Adjustment ...................................................................................G-34 (2)-1 Front Wheel ..........................................................................................G-34 (2)-2 Rear Wheels ..........................................................................................G-34 (3) Wheel Hub .............................................................................................. G-36 (4) Tire Pressure ............................................................................................ G-36 (5) Tire Liquid Injection ................................................................................G-37 [11] SPECIFICATIONS OF IMPLEMENT LIMITATIONS .......................................... G-40 •

Kubota B1700/B2100/B2400 Tractors OEM Service & Repair Manual

You're Reading a Preview

Recently Viewed