Toro Groundsmaster 300 Series Full Service & Repair Manual

Part No. 92801SL, Rev. I Service Manual Groundsmaster ® 300 Series Preface Groundsmaster 328-D Use this book along with the Toro Operator’s Manual and Parts Catalog for the specific model and serial number of the machine, and the Kubota 05 Series Workshop Manual. This publication will provide the service technician with information for troubleshooting, testing, and repair of major systems and components on the Groundsmaster 345, 322-D and 325-D (Model 30788 and 30795). REFER TO THE TRACTION UNIT AND CUTTING UNIT OPERATOR’S MANUALS FOR OPERATION, MAINTENANCE AND ADJUSTMENT INSTRUC- TIONS. Space is provided in Chapter 2 of this book to insert the Operator’s Manuals and Parts Catalogs for your machine. Replacement Operator’s Manuals are available by sending complete Model and Serial Num- ber of traction unit and cutting unit to: The Toro Company 8111 Lyndale Avenue South Minneapolis, MN 55420 The Toro Company reserves the right to change product specifications or this publication without notice. This safety symbol means DANGER, WARN- ING, or CAUTION, PERSONAL SAFETY IN- STRUCTION. When you see this symbol, carefully read the instructions that follow. Failure to obey the instructions may result in personal injury. NOTE: A NOTE will give general information about the correct operation, maintenance, service, testing or repair of the machine. IMPORTANT: The IMPORTANT notice will give important instructions which must be followed to prevent damage to systems or components on the machine. © The Toro Company - 1992, 1996, 1998, 2001, 2003, 2004, 2005, 2007

Table Of Contents Chapter 1 - Safety Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 Chapter 2 - Product Records and Manuals Product Records . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 Equivalents and Conversions . . . . . . . . . . . . . . . . 2 - 2 Torque Specifications . . . . . . . . . . . . . . . . . . . . . . 2 - 3 Maintenance Interval Charts. . . . . . . . . . . . . . . . . 2 - 4 Equipment Operational and Service Historical Report Record Chapter 3 - Ford VSG-411 Gasoline Engine Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 General Information . . . . . . . . . . . . . . . . . . . . . . . 3 - 2 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6 FORD VSG-411/413 ENGINE SERVICE MANUAL Chapter 4 - Mitsubishi K3D Diesel Engine Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2 Specificationis. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3 Special Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 11 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 13 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 15 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 18 Preparation for Engine Repair . . . . . . . . . . . . . . 4 - 25 External Engine Component Repair . . . . . . . . . . 4 - 26 Fuel System Repairs . . . . . . . . . . . . . . . . . . . . . 4 - 34 Removing and Installing the Engine . . . . . . . . . . 4 - 46 Cylinder Head Overhaul . . . . . . . . . . . . . . . . . . . 4 - 47 Cylinder Block Overhaul . . . . . . . . . . . . . . . . . . . 4 - 53 Chapter 4A - Kubota Diesel Engine General Information . . . . . . . . . . . . . . . . . . . . . . . 4 - 2 Specificationis. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3 Chapter 5 - Hydraulic System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2 General Information . . . . . . . . . . . . . . . . . . . . . . . 5 - 3 Hydraulic Schematics . . . . . . . . . . . . . . . . . . . . . . 5 - 6 Hydraulic Flow Diagrams . . . . . . . . . . . . . . . . . . . 5 - 7 Special Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 12 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 18 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 22 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 26 Chapter 6 - Electrical System Wiring Schematics . . . . . . . . . . . . . . . . . . . . . . . . 6 - 2 Special Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 3 Troubleshooting (Groundsmaster 345) . . . . . . . . . . . . 6 - 6 Troubleshooting (Groundsmaster 322-D/325-D) . . . . . 6 - 12 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 18 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 30 Chapter 6A - Electrical System (S/N 21000000 & Up) Wiring Schematics . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1 Special Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 2 Electrical System Quick ChecksT. . . . . . . . . . . . . 6 - 3 Component Identification and Testing. . . . . . . . . . 6 - 4 Service and Repairs . . . . . . . . . . . . . . . . . . . . . . 6 - 12 Chapter 7 - Differential Axle Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 3 Chapter 8 - Steering and Brakes Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 4 Special Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 5 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 7 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 11 Chapter 9 - Transmission Coupler and PTO Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 4 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 7 Chapter 10 - 4WD Rear Axle (GM322-D or GM325-D with Inasaka axle) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 General Information . . . . . . . . . . . . . . . . . . . . . . 10 - 3 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 5 Chapter 10.1 - 4WD Rear Axle (GM325-D or GM328-D with Dae Dong axle) Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4 Groundsmaster ® 300 Series

Chapter 11 - 72″ Cutting Units Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 2 General Information . . . . . . . . . . . . . . . . . . . . . . 11 - 3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 5 Adjustments. Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 8 Chapter 12 - Triflex ® 88″ Cutting Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 2 General Information . . . . . . . . . . . . . . . . . . . . . . 12 - 3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 5 Adjustments. Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 13 Chapter 13 - Guardian ® 72″ Recycler ® Cutting Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 4 Adjustments. Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 7 Groundsmaster ® 300 Series

Chapter 1 Safety SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . 1 Before Operating . . . . . . . . . . . . . . . . . . . . . . . . . 1 While Operating. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Instructions The Groundsmaster 300 Series was tested and certified by TORO for compliance with the B71.4 1984 specifications of the American National Standards Institute. Al- though hazard control and accident prevention partially are dependent upon the design and configuration of the machine, these factors are also dependent upon the awareness, concern, and proper training of the person- nel involved in the operation, transport, maintenance, and storage of the machine. Before Operating 1. Read and understand the Operator’s Manual before starting and operating the machine. Become familiar with all controls and know how to stop quickly. A replacement manual is available by sending complete Model and Serial Numbers to: The Toro Company 8111 Lyndale Avenue South Minneapolis, Minnesota 55420 2. Never allow children to operate the machine. Do not allow adults to operate the machine without proper instruction. Only trained operators, skilled in slope operation and who have read the Operator’s Manual should operate this machine. 3. Never operate machine when under the influence of drugs or alcohol. 4. Remove all debris or other objects that might be picked up and thrown by cutter blades or fast moving components from other attached implements. Keep all bystanders away from the operating area. 5. Keep all shields and safety devices in place. If a shield, safety device, or decal is defective or damaged, repair or replace it before operating the machine. Also, tighten any loose nuts, bolts, and screws to make sure machine is in safe operating condition. While Doing Maintenance, Troubleshooting, Testing, Adjustments or Repairs . . . . . . . . . . . . . 3 j Improper operation, maintenance, troubleshooting, testing, adjustments or repairs of the machine can result in in ury or death. To reduce the potential for injury or death, comply with the following safety instructions. CAUTION 6. Do not wear loose fitting clothing because it could get caught in moving parts. Always wear long pants and substantial shoes. Wearing safety glasses, safety shoes, and a helmet is advisable and required by some local ordinances and insurance regulations. 7. Be sure interlock switches are adjusted correctly so engine cannot be started unless traction pedal is released to neutral position and PTO lever is in OFF position. 8. Grass deflectors must be installed in lowest position on side discharge cutting units and properly attached to Triflex ® cutting unit wings. 9. Fill fuel tank with the proper fuel before starting the engine. Avoid spilling any fuel. Since fuel is very flammable, handle it carefully. A. Use an approved fuel container. B. Do not fill fuel tank when engine is hot or running. C. Do not smoke while handling fuel. D. Fill fuel tank outdoors and up to about one inch (25 mm) from the top of the tank, not the filler neck. E. Wipe up any spilled fuel. Groundsmaster ® 300 Series Page 1 - 1 Safety Instructions

10. Sit on the seat when starting the engine and operating the machine. 11. On machines equipped with roll-over protection (ROPS), always use seat belt and ROPS together. Make sure seat pivot retaining pin is installed. 12. Before starting the engine: A. Engage parking brake, B. Make sure traction pedal is in neutral and PTO is in OFF (disengage) position. C. After engine is started, release parking brake and keep foot off traction pedal. Machine must not move. If movement is evident, the neutral return mecha- nism is adjusted incorrectly. Shut engine off and adjust until machine does not move when traction pedal is released. 13. Do not run the engine in a confined area without adequate ventilation. Exhaust fumes are hazardous and could possibly be deadly. 14. Maximum seating capacity is one person. Therefore, never carry passengers. 15. Check carefully for overhead clearances before driving under any objects. While Operating 16. Using the machine demands the operator’s complete attention. To prevent loss of control: A. Operate only in daylight or when there is good artificial light. B. Drive slowly. C. Avoid sudden stops and starts. D. Look behind machine before backing up. E. Watch for holes or other hidden hazards. F. Do not drive close to a sand trap, ditch, creek, or hazard. G. Reduce speed when making sharp turns and when turning on a hillside H. The cutting deck must be lowered when going down slopes for steering control. 17. To maintain machine control, 35 lb. of weight must be mounted on rear of traction unit before using the Triflex 88" cutting unit. More weight may be required in some steeper slope conditions. 18. Operator must be skilled and trained in how to drive on hillsides. Failure to use caution on slopes or hills may cause loss of control and vehicle to tip or roll possibly resulting in personal injury or death. 19. Traverse slopes carefully. Do not start or stop sud- denly when traversing slopes or when traveling uphill or downhill. 20. If engine stalls or machine loses headway and cannot make it to the top of a slope, do not turn machine around. Always back slowly straight down the slope. 21. The grass deflector(s) must always be installed and in lowest position on the cutting unit. This product is designed to drive objects into the ground where they lose energy quickly in grassy areas. However, don’t take an injury risk!! When a person or pet appears unexpect- edly in or near the mowing area, STOP MOWING. Careless operation, combined with terrain angles, rico- chets, or improperly positioned guards, can lead to thrown object injuries. Do not resume mowing until area is cleared. 22. Never raise the cutting unit or other attached implement while the blades or other parts are rotating. 23. If cutting blades or other implement components strike a solid object or the machine vibrates abnormally, disengage PTO, move throttle to SLOW, set parking brake, and shut engine off. Remove key from switch to prevent possibility of accidental starting. Check cutting unit or other implement and traction unit for damage and defective parts. Repair any damage before restarting the engine and operating the implement or cutting unit. Assure cutting unit blades are in good condition and blade bolts are torqued to proper specifications (See Cutting Unit Operator’s Manual). 24. To stop machine, remove foot from traction pedal and use brakes. Gradually reversing the traction pedal can provide additional braking. 25. Do not touch engine, muffler, or radiator while engine is running or soon after it has stopped. These areas could be hot enough to cause a burn. 26. Lower the cutting unit or other attached implement to the ground and remove key from switch whenever machine is left unattended. Safety Instructions Page 1 - 2 Groundsmaster ® 300 Series

27. Before getting off the seat: B. Set the parking brake and disengage the PTO. A. Move traction pedal to neutral position and re- C. Shut the engine off and remove key from ignition move foot from pedal. switch. Wait for all movement to stop before getting off the seat. While Doing Maintenance, Troubleshooting, Testing, Adjustments or Repairs 28. Remove key from ignition switch to prevent accidental starting of the engine when servicing, adjusting, or storing the machine. 29. Make sure you understand a service procedure before working on the machine. Unauthorized modifica- tions to the machine may impair the function, safety and life of the machine. If major repairs are ever needed or assistance is desired, contact an Authorized TORO Distributor. 30. To reduce potential fire hazard, keep the engine free of excessive grease, grass, leaves, and accumulations of dirt. Clean protective screen on front of engine frequently. When cleaning parts, do not use flammable solvents, such as diesel fuel, kerosene or gasoline. 31. THE ASBESTOS BRAKE LININGS CONTAIN ASBES- TOS FIBERS. BREATHING ASBESTOS DUST MAY BE HAZ- ARDOUS TO YOUR HEALTH AND MAY CAUSE SERIOUS RESPIRATORY OR OTHER BODILY HARM. For your protection: A. AVOID CREATING DUST. B. Do not remove brake drum without proper equipment. C. Do not work on brake linings without proper protective equipment. D. Do not replace brake linings without proper protective equipment. E. Do not attempt to sand, grind, chisel, file, hammer, or alter brake linings in any manner without proper protective equipment. F. Follow O.S.H.A standards for proper protective devices to be used when working with asbestos materials. 32. If the cutting unit discharge area ever plugs, disengage PTO and shut engine off before removing the obstruction. 33. Make sure machine is in safe operating condition by keeping nuts, bolts, and screws tight. Check all cutting unit blade mounting bolts frequently to assure they are torqued to proper specifications (See Cutting Unit Op- erator’s Manual). 34. If machine is equipped with roll-over protection (ROPS), periodically inspect the roll bar and roll bar mounting. Repair as necessary. Do not weld, cut, drill, or modify roll bar in any manner. 35. Make sure all hydraulic line connectors are tight, and all hydraulic hoses and lines are in good condition before applying pressure to the system. 36. Keep body and hands away from pin hole leaks or nozzles that eject hydraulic fluid under high pressure. Use paper or cardboard, not hands, to search for leaks. Hydraulic fluid escaping under pressure can have suffi- cient force to penetrate skin and do serious damage. If fluid is ejected into the skin, it must be surgically re- moved within a few hours by a doctor familiar with this form of injury or gangrene may result. 37. Before disconnecting or performing any work on the hydraulic system, all pressure in system must be re- lieved by stopping engine and lowering implement to the ground. 38. If the engine must be running to perform maintenance or an adjustment, keep clear of PTO shaft, cutting unit blades, and other moving parts. 39. Do not over-speed the engine by changing the governor settings. To ensure safety and accuracy, have an Authorized TORO Distributor check maximum engine speed with a tachometer. 40. Engine must be shut off before checking oil or adding oil to the crankcase. 41. Disconnect the cables from the battery before servicing the machine. If battery voltage is required for troubleshooting or test procedures, temporarily connect the battery. 42. Do not charge a frozen battery because it can explode and cause injury. Let the battery warm to 60° F (15.5° C) before connecting to a charger. Charge the battery in a well-ventilated place so that gases produced while charging can dissipate. Since the gasses are explosive, keep open flame and electrical spark away from the battery; do not smoke. Nausea may result if the gases are inhaled. Unplug the charger from the electrical outlet before connecting or disconnecting the charger leads from the battery posts. Groundsmaster ® 300 Series Page 1 - 3 Safety Instructions

43. Wear safety glasses, goggles or a face shield to prevent possible eye injury when using compressed air for cleaning or drying components. 44. Failure to follow proper procedures when mounting a tire on a wheel or rim can produce an explosion which may result in serious injury. Do not attempt to mount a tire unless you have the proper equipment and experi- ence to perform the job. Have it done by your Toro Distributor or a qualified tire service. 45. When changing attachments or performing other service, use the correct blocks, hoists and jacks. Always use jack stands to safely support the machine when it is raised by a jack or hoist. 46. At the time of manufacture, the machine conformed to safety standards in effect for riding mowers. To ensure optimum performance and continued safety certification of the machine, use genuine TORO replacement parts and accessories. Replacement parts and accessories made by other manufacturers may result in non confor- mance with the safety standards, and the warranty may be voided. Safety Instructions Page 1 - 4 Groundsmaster ® 300 Series

Chapter 2 Product Records and Manuals Table of Contents PRODUCT RECORD FORM . . . . . . . . . . . . . . . . . . 1 EQUIVALENTS AND CONVERSIONS . . . . . . . . . . 2 Decimal and Millimeter Equivalents . . . . . . . . . . 2 U.S. to Metric Conversions . . . . . . . . . . . . . . . . . 2 Product Records Record information about your Groundsmaster 345, 322-D or 325-D on the Equipment Operation and Serv- ice History Report Form. Use this information when referring to your machine. TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . 3 Capscrew Markings and Torque Values - U.S. . . 3 Capscrew Markings and Torque Values - Metric . 3 EQUIPMENT OPERATION AND SERVICE HISTORY REPORT FORM Insert Operator’s Manuals and Parts Manuals for your Groundsmaster 345, 322-D or 325-D at the end of this section. Groundsmaster ® 300 Series Page 2 - 1 Rev. A Product Records

___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ ___________________________________________________________________________________________________ Equivalents and Conversions Decimal and Millimeter Equivalents Fractions Decimals mm Fractions Decimals mm 1/64 0.015625 — 0.397 33/64 0.515625 — 13.097 1/32 ––––– 0.03125 — 0.794 17/32 –––– 0.53125 — 13.494 3/64 0.046875 — 1.191 35/64 0.546875 — 13.891 1/16 –––––––––––– 0.0625 — 1.588 9/16 –––––––––––– 0.5625 — 14.288 5/64 0.078125 — 1.984 37/64 0.578125 — 14.684 3/32 ––––– 0.9375 — 2.381 19/32 –––– 0.59375 — 15.081 7/64 0.109275 — 2.778 39/64 0.609375 — 15.478 1/8 ––––––––––––– 0.1250 — 3.175 5/8 ––––––––––––– 0.6250 — 15.875 9/64 0.140625 — 3.572 41/64 0.640625 — 16.272 5/32 ––––– 0.15625 — 3.969 21/32 –––– 0.65625 — 16.669 11/64 0.171875 — 4.366 43/64 0.671875 — 17.066 3/16 –––––––––––– 0.1875 — 4.762 11/16 ––––––––––– 0.6875 — 17.462 13/64 0.203125 — 5.159 45/64 0.703125 — 17.859 7/32 ––––– 0.21875 — 5.556 23/32 –––– 0.71875 — 18.256 15/64 0.234375 — 5.953 47/64 0.734375 — 18.653 1/4 ––––––––––––– 0.2500 — 6.350 3/4 ––––––––––––– 0.7500 — 19.050 17/64 0.265625 — 6.747 49/64 0.765625 — 19.447 9/32 ––––– 0.28125 — 7.144 25/32 –––– 0.78125 — 19.844 19/64 0.296875 — 7.541 51/64 0.796875 — 20.241 5/16 –––––––––––– 0.3125 — 7.938 13/16 ––––––––––– 0.8125 — 20.638 21/64 0.328125 — 8.334 53/64 0.828125 — 21.034 11/32 –––– 0.34375 — 8.731 27/32 –––– 0.84375 — 21.431 23/64 0.359375 — 9.128 55/64 0.859375 — 21.828 3/8 ––––––––––––– 0.3750 — 9.525 7/8 ––––––––––––– 0.8750 — 22.225 25/64 0.390625 — 9.922 57/64 0.890625 — 22.622 13/32 –––– 0.40625 — 10.319 29/32 –––– 0.90625 — 23.019 27/64 0.421875 — 10.716 59/64 0.921875 — 23.416 7/16 –––––––––––– 0.4375 — 11.112 15/16 ––––––––––– 0.9375 — 23.812 29/64 0.453125 — 11.509 61/64 0.953125 — 24.209 15/32 –––– 0.46875 — 11.906 31/32 –––– 0.96875 — 24.606 31/64 0.484375 — 12.303 63/64 0.984375 — 25.003 1/2 ––––––––––––– 0.5000 — 12.700 1 –––––––––––––– 1.000 — 25.400 1 mm = 0.03937 in. 0.001 in. = 0.0254 mm U.S to Metric Conversions To Convert Into Multiply By Linear Miles Kilometers 1.609 Measurement Yards Meters 0.9144 Feet Meters 0.3048 Feet Centimeters 30.48 Inches Meters 0.0254 Inches Centimeters 2.54 Inches Millimeters 25.4 Area Square Miles Square Feet Square Inches Acre Square Kilometers 2.59 Square Meters 0.0929 Square Centimeters 6.452 Hectare 0.4047 Volume Cubic Yards Cubic Feet Cubic Inches Cubic Meters 0.7646 Cubic Meters 0.02832 Cubic Centimeters 16.39 Weight Tons (Short) Pounds Ounces (Avdp.) Metric Tons 0.9078 Kilograms 0.4536 Grams 28.3495 Pressure Pounds/Sq. In. Kilopascal 6.895 Work Foot-pounds Foot-pounds Inch-pounds Newton-Meters 1.356 Kilogram-Meters 0.1383 Kilogram-Centimeters 1.152144 Liquid Volume Quarts Liters 0.9463 Gallons Liters 3.785 Liquid Flow Gallons/Minute Liters/Minute 3.785 Temperature Fahrenheit Celsius 1. Subract 32 o 2. Multiply by 5/9 Equivalents and Conversions Page 2 - 2 Groundsmaster ® 300 Series

Toro Groundsmaster 300 Series Full Service & Repair Manual

You're Reading a Preview

Recently Viewed