STIH)
STIHL Series 4144 Components
FC, FS, KM
2008-02
FS 40, FS 50, FS 56
FC 56
KM 56
1 Series 4144 Components FC, FS, KM
q
© ANDREAS STIHL AG & Co. KG, 2008
RA_545_01_01_01
1. Introduction 2
2. Safety Precautions 3
3. Specifications 4
3.1 Engine 4
3.2 Fuel System 4
3.3 Ignition System 4
3.4 Tightening Torquese 5
4. Troubleshooting 7
4.1 Clutch 7
4.2 Rewind Starter 8
4.3 Ignition System 9
4.4 Carburetor 11
4.5 Engine 14
5. Engine 15
5.1 Removing and
Installing 15
5.2 Leakage test 16
5.3 Oil seals 16
5.4 Ignition Module /
Spark Plug Boot 16
5.5 Clutch 16
5.6 Flywheel 16
5.7 Motor 16
5.8 Muffler / Spark
Arresting Screen 19
5.9 Short Circuit Wire 20
5.9.1 Testing 20
5.9.2 Removing and
Installing
(Loop Handle Version) 20
5.9.3 Removing and
Installing
(Bike Handle Version) 23
5.9.4 Ground Wire 26
5.10 Ignition System
Troubleshooting 27
6. Rewind Starter 30
6.1 General 30
6.2 Removing and
Installing 30
6.3 Pawls 30
6.3.1 Carrier 31
6.4 Rope Rotor 32
6.5 Starter Rope / Grip 33
6.6 Tensioning the
Rewind Spring 35
6.7 Replacing the
Rewind Spring 36
6.8 ErgoStart 36
7. Control Levers 37
7.1 Switch Shaft /
Control Lever 37
7.2 Switch Positions 37
7.3 Interlock Lever
(Loop Handle) 37
7.3.1 Throttle Trigger 38
7.4 Throttle Trigger/
Interlock Lever
(Bike Handle) 40
7.5 Handlebar
(Bike Handle) 43
8. Fuel System 44
8.1 Air Filter 44
8.1.1 Baffle 44
8.1.2 Filter housing 44
8.2 Removing and
Installing
the Carburetor 45
8.3 Leakage Test 47
8.4 Servicing
the Carburetor 47
8.4.1 Metering Diaphragm /
Manual Fuel Pump 47
8.4.2 Inlet Needle 49
8.4.3 Pump Diaphragm 49
8.4.4 Throttle Lever /
Rotary Knob 51
8.4.5 Adjusting Screws 52
8.5 Adjusting
the Carburetor 54
8.5.1 Basic Setting 54
8.5.2 Standard Setting 55
8.6 Removing and
Installing Throttle Cable
(Loop Handle) 56
8.6.1 Removing and
Installing Throttle Cable
(Bike Handle) 58
8.6.2 Adjusting the
Throttle Cable 58
8.7 Removing and
Installing the Spacer
Flange 59
8.8 Tank Vent 60
8.8.1 Testing 60
8.8.2 Removing and
Installing 61
8.9 Fuel Intake 61
8.9.1 Pickup Body 61
8.9.2 Fuel Hoses 62
8.9.3 Fuel Tank Cap 63
8.10 Removing and
Installing the Engine
Housing 64
9. Drive Tube 65
9.1 Removing and
Installing 65
9.1.1 Disassembling
(KM 56) 66
9.1.2 Disassembling
(FC 56) 68
9.1.3 Disassembling
(FS 56) 69
9.1.4 Disassembling
(FS 40, 50) 70
9.1.5 Removing and
Installing the
Bearing Housing 71
9.1.6 Loop Handle 72
9.1.7 Loop Handle with
Barrier Bar 73
9.2 Add-On Components 74
9.2.1 Deflector for Machines
without Gearbox 74
9.2.2 Deflector for Machines
with Gearbox 74
9.2.3 One-part
Carrying Ring 75
9.2.4 Retainer 75
9.3 Gearbox 75
10. Special
Servicing Tools 76
11. Servicing Aids 77
Contents
2 Series 4144 Components FC, FS, KM
1. Introduction
This service manual contains
detailed descriptions of all the repair
and servicing procedures specific to
this power tool.
You should make use of the
illustrated parts lists while carrying
out repair work. They show the
installed positions of the individual
components and assemblies.
Refer to the latest edition of the
relevant parts list to check the part
numbers of any replacement parts.
A fault on the machine may have
several causes. To help locate the
fault, consult the troubleshooting
charts for all assemblies and
systems in this manual and the
"STIHL Service Training System".
Refer to the “Technical Information”
bulletins for engineering changes
which have been introduced since
publication of this service manual.
Technical information bulletins also
supplement the parts list until a
revised edition is issued.
The special tools mentioned in the
descriptions are listed in the chapter
on "Special Servicing Tools" in this
manual. Use the part numbers to
identify the tools in the
"STIHL Special Tools" manual. The
manual lists all special servicing
tools currently available from
STIHL.
Symbols are included in the text and
pictures for greater clarity.
The meanings are as follows:
In the descriptions:
: = Action to be taken as
shown in the illustration above
the text
– = Action to be taken that is
not shown in the illustration
above
the text
In the illustrations:
A Pointer
aDirection of movement
@ 4.2 = Reference to another
chapter, i.e. chapter 4.2
in this example
Service manuals and all technical
information bulletins are intended
exclusively for the use of properly
equipped repair shops. They must
not be passed to third parties.
Always use original STIHL
replacement parts.
They can be identified by the STIHL
part number,
the {
logo and the
STIHL parts symbol K
This symbol may appear alone on
small parts.
Storing and disposing of oils and
fuels
Collect fuel or lubricating oil in a
clean container and dispose of it
properly in accordance with local
environmental regulations.
3 Series 4144 Components FC, FS, KM
2. Safety Precautions
If the engine is started up in the
course of repairs or maintenance
work, observe all local and country-
specific safety regulations as well
as the safety precautions and
warnings in the instruction manual.
Gasoline is an extremely flammable
fuel and can be explosive in certain
conditions.
Always wear suitable protective
gloves for operations in which
components are heated for
assembly or disassembly.
Improper handling may result in
burns or other serious injuries.
Do not smoke or bring any fire,
flame or other source of heat near
the fuel. All work with fuel must be
performed outdoors only. Spilled
fuel must be wiped away
immediately.
Always perform leakage test after
working on the fuel system and the
engine.
4 Series 4144 Components FC, FS, KM
3. Specifications
3.1 Engine
FS 40 FS 50, 56, FC 56, KM 56
Displacement: 27.2 cm
3
27.2 cm
3
Bore: 34 mm 34 mm
Stroke: 30 mm 30 mm
Engine power to ISO 8893: 0.7 kW (1.0 bhp)
at 8,500 rpm
0.8 kW (1.1 bhp)
at 8,500 rpm
Max. permissible speed
(with cutting attachment): 10,000 rpm 10,000 rpm
Idle speed: 2,800 rpm 2,800 rpm
Clutch: Centrifugal clutch without
linings
Centrifugal clutch without
linings
Clutch engages at: 4,200 rpm 4,200 rpm
Crankcase leakage test
at gauge pressure: 0.5 bar
under vacuum: 0.5 bar
3.2 Fuel System
Carburetor leakage test at
gauge pressure:
0.3 bar
Operation of tank vent at
gauge pressure:
0.5 bar
Fuel: as specified in instruction
manual
3.3 Ignition System
Air gap between ignition
module and fanwheel: 0.30 mm
Spark plug (suppressed): NGK CMR6H
NGK 6H
Bosch WSR 6 F
Electrode gap: 0.5 mm
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$39.99
Stihl FS-KM Factory Service & Work Shop Manual
Viewed 71 Times Today
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$39.99
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Offline Viewing
Access Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
Upon purchasing this manual, you will receive a .PDF file containing an email contact. After contacting us, you will receive a reply with a link to access the manual for your Stihl FS-KM.
This comprehensive manual covers every aspect of your machine, providing detailed guidance on every nut and bolt. With hundreds of pages, it offers solutions for various issues, from simple tasks like an oil change to more complex procedures like a transmission swap. The manual includes numerous illustrations to assist you and features easy-to-understand text throughout.
Utilize the search function to navigate the manual efficiently and print the necessary pages as needed. This Factory Service Repair Manual is designed to walk you through the fundamentals of maintenance and repair, providing a step-by-step approach to equip you with the knowledge mastered by factory-trained technicians.
By leveraging the insights offered in this service repair manual, any owner can confidently make informed decisions regarding the maintenance and repair of their machine.
Rest assured, in addition to the high-quality service manual, we are committed to delivering exceptional customer service, ensuring your satisfaction.
