Landini Trekker 80C Factory Service & Work Shop Manual

Trekker 70-80-90-100 / C-CF-CFL Series Training manual P/N° 3662270M2

TABLE OF CONTENTS Chap. 1 INTRODUCTION Chap. 2 ENGINE Chap. 3 CLUTCH Chap. 4 TRANSMISSION Chap. 5 STEERING CLUTCH ASSEMBLIES & BRAKES Chap. 6 TRACKS Chap. 7 LOW PRESSURE HYDRAULIC CIRCUIT Chap. 8 HIGH PRESSURE HYDRAULIC CIRCUIT Chap. 9 MECHANICAL POWER LIFT Chap.10 ELECTRICAL SYSTEM Chap.11 SPECIAL TOOLS TABLE OF CONTENTS

PRE-SALE SERVICE June 2003 42042 FABBRICO (RE) ITALY PREFACE This manual contains the technical specifications, mechanical, hydraulic layouts and wiring diagrams, plus instructions on how to operate and adjust 70-80-90-100/C-CF-CFL Series Trekker tractors. It does not contain all the necessary information as it is completed with the theoretical and practical explanations and theoretical descriptions given by the instructors during the training courses. This information is therefore dedicated to the persons who frequent training courses at the Landini training center. NOTE : The descriptions and technical specifications in this manual are strictly not binding. Landini therefore reserves the right to modify the components and accessories for technical or commercial reasons without being obliged to update this manual each time.

1 - 1 INTRODUCTION TABLE OF CONTENTS Sect. 1 Reading the manual. ............................................................... 1-3 1-1 Introduction ................................................................... 1-4 1-2 Structure of the manual ................................................ 1-4 Sect. 2 Tractor identification and technical specifications. ............ 1-5 2-1 Tractor identification ..................................................... 1-6 2-2 Weights and dimensions .............................................. 1-7 2-3 Engine specifications ................................................... 1-9 2-4 Clutch specifications ................................................. 1-11 2-5 Transmission, steering clutch & brake specifications .. 1-11 2-6 Power take-off specifications .................................... 1-14 2-7 Track specifications ................................................... 1-15 Sect. 3 Working in safety................................................................... 1-17 3-1 Essential rules for accident prevention ..................... 1-18 3-2 Safety decals ............................................................. 1-24 3-3 Replacing tractor parts .............................................. 1-30 3-4 Safe use of the tractor ............................................... 1-30 Sect. 4 Pre-delivery inspections and maintenance. ..................... 1-33 4-1 General information ................................................... 1-34 4-2 Inspections before delivery ....................................... 1-34 4-3 Routine maintenance guide ...................................... 1-35 CHAP.1

INTRODUCTION 1 - 2 CHAP.1 Sect. 5 Conversion tables. ................................................................ 1-37 5-1 Length ........................................................................ 1-38 5-2 Area ........................................................................... 1-41 5-3 Volume ....................................................................... 1-42 5-4 Weight ........................................................................ 1-45 5-5 Pressure .................................................................... 1-47 5-6 Moment of rotation .................................................... 1-49 5-7 Temperature .............................................................. 1-51 Sect. 6 Sealants. ................................................................................ 1-53 Sect. 7 Table of bolt driving torques. .............................................. 1-55 Sect. 8 General assembly instructions. .......................................... 1-57 8-1 Seals .......................................................................... 1-58 8-2 O-rings ....................................................................... 1-59 8-3 Bearings .................................................................... 1-60

1 - 3 INTRODUCTION TABLE OF CONTENTS Sect.1 Reading the manual 1-1 Introduction ................................................................... 1-4 1-2 Structure of the manual ................................................ 1-4 CHAP. 1 Reading the manual

INTRODUCTION 1 - 4 Sect.1 - Reading the manual 1-1 Introduction The purpose of this training manual is to provide clear instructions on how to repair Trekker tractors. The manual is for the chief foreman since it does not describe the demounting, remounting and adjustment operations in detail and for all assemblies, merely tho- se that require particular expertise or recommenda- tions. Before reading the manual, it is essential to read sect.3: WORKING IN SAFETY in order to prevent errors or mistakes that could jeopardize the safety of the technicians in the workshop. The information in this manual was up to date at the time of publication. Landini reserves the right to make modifications without being obliged to give notice. Please contact your area dealer or the importer if di- screpancies are discovered or for any other require- ment. 1-2 Structure of the manual The manual is divided into chapters (chap.) and each chapter into sections (sect.). Page numbering begins with 1 for each chapter with the number of the chapter itself alongside. Example: 5-7 indicates page 7 of chapter 5. Numbering of the figures also begins with 1 in each chapter with the chapter number alongside. Example: Fig. 73-5, indicates figure 73 of chapter 5.

1 - 5 INTRODUCTION TABLE OF CONTENTS Sect.2 Tractor identification and technical specifications 2-1 Tractor identification ..................................................... 1-6 2-2 Weights and dimensions .............................................. 1-7 2-3 Engine specifications ................................................... 1-9 2-4 Clutch specifications ................................................. 1-11 2-5 Transmission, steering clutch & brake specifications .. 1-11 2-6 Power take-off specifications .................................... 1-14 2-7 Track specifications ................................................... 1-15 CHAP. 1 Tractor identification and technical specifications

INTRODUCTION 1 - 6 Sect. 2 - Tractor identification & technical specifications 2-1 Tractor identification The tractor is identified by a serial number stamped on the front support (ballast holder) and on the bonnet. The engine also has its own serial number stamped on the engine block To ensure a quick and efficient service when ordering spare parts or asking for technical specifications or other information, always state the chassis and engine serial number. Chassis serial number .............................................. Engine serial number ............................................... Type of tractor .......................................................... Owner / Operator ...................................................... Dealer's or Agent's address ...................................... ................................................................................ Delivery date ............................................................ Warranty expiry date ................................................ Fig.1-1 Fig.3-1 Fig.2-1

1 - 7 INTRODUCTION Tractor identification & technical specifications 2-2 Weights and dimensions Fig.4-1 ST L L ST L L ST L L 310 360 360 360 360 360 360 360 360 4080 4130 4130 4160 4160 4260 4200 4300 4370 3500 3500 3500 3500 3500 3500 3500 3500 3500 1410 1460 1660 1460 1460 1700 1460 1700 1760 1170 1170 1170 1170 1170 1170 1170 1170 1170 2320 2320 2320 2320 2320 2320 2320 2320 2320 1100 1100 1300 1100 1100 1300 1100 1300 1300 1650 1650 1650 1650 1650 1650 1650 1650 1650 310 360 360 360 360 400* 360 400* 450* 270 270 270 270 270 270 270 270 270 General specifications ST = Narrow L = Wide -Withshoesmounted .................................................................... mm Weights -Inrunningorderwithhydraulicpowerlift,three-pointhitchandsafetyframe,without ballastandroadpads .................................................................... kg Dimensions A- Max. length (with ballast and with links lifted) .................................. mm B- Width (with310-360shoes) ............................................................... mm C- Heightatbonnet ...................................................................... mm D- Height at safety frame .............................................................. mm E- Track .................................................................................... mm F - Wheelbase ............................................................................ mm G- Shoewidth ............................................................................. mm H- Groundclearance ..................................................................... mm *OPTIONALavailableonrequest 70 70 70 70 70 80 80 80 80 80 90 90 90 90 90 CF CFL CF CFL CF CFL

Landini Trekker 80C Factory Service & Work Shop Manual

You're Reading a Preview

Recently Viewed