2006-2011 Toyota Yaris (XP90) OEM Service & Repair Manual

1NZ-FE CHARGING – CHARGING SYSTEM CH–1 CH CHARGING SYSTEM PRECAUTION 1. Check that the battery cables are connected to the correct terminals. 2. Disconnect the battery cables when the battery is given a quick charge. 3. Never disconnect the battery while the engine is running. 4. Check that the charging cable is tightly connected to terminal B of the generator. Terminal B A125204E01

CH–2 1NZ-FE CHARGING – CHARGING SYSTEM CH PARTS LOCATION GENERATOR A119213E01

1NZ-FE CHARGING – CHARGING SYSTEM CH–3 CH SYSTEM DIAGRAM W Combination Meter 7.5A MET Charge Generator FL MAIN Battery IC Regulator EC ECM B L E A119142E01

CH–4 1NZ-FE CHARGING – CHARGING SYSTEM CH ON-VEHICLE INSPECTION CAUTION: If the battery is weak or if the engine is difficult to start, recharge the battery and perform the inspections again before returning the vehicle to the customer. 1. CHECK BATTERY CONDITION (a) Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery. (b) Check the volume of electrolyte in each cell. (1) For batteries that are maintenance-free: • If the electrolyte volume is below the lower line, replace the battery. • If the electrolyte volume is above the lower line, check the battery voltage when cranking the engine. • If the voltage is less than 9.6 V, recharge or replace the battery. HINT: Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, etc.). (2) For batteries that are not maintenance-free: • If the electrolyte volume is below the lower line, add distilled water to each cell. Then, recharge the battery and check the specific gravity of the electrolyte. Standard specific gravity: 1.25 to 1.29 at 20 °C ( 68 °F) If the electrolyte volume is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery. HINT: Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.). 2. CHECK BATTERY TERMINAL AND FUSE (a) Check that the battery terminals are not loose or corroded. If the terminals are corroded, clean the terminals. (b) Measure the resistance of the H-fuse and fuses. Standard resistance: Below 1 Ω If the results are not as specified, replace the fuses as necessary.

1NZ-FE CHARGING – CHARGING SYSTEM CH–5 CH 3. CHECK V-RIBBED BELT (a) Check the belt for wear, cracks and other signs of damage. If any defects are found, replace the V-ribbed belt. HINT: Replace the drive belt if any of the following defects are found: • The belt is worn out and the wire is exposed. • The cracks reach the wire in more than one place. • The belt has pieces missing from the ribs. (b) Check that the belt fits properly into the ribbed grooves. HINT: With your hand, confirm that the belt has not slipped out of the grooves on the bottom of the pulley. 4. VISUALLY CHECK GENERATOR WIRING (a) Check that the wiring is in good condition. 5. LISTEN FOR ABNORMAL NOISES FROM GENERATOR (a) Check that the generator does not emit any abnormal noise while the engine is running. 6. CHECK CHARGE WARNING LIGHT CIRCUIT (a) Turn the ignition switch on (IG). Check that the charge warning light turns on. (b) Start the engine and check that the light turns off. If the light does not operate as specified, troubleshoot the charge warning light circuit. 7. CHECK CHARGING CIRCUIT WITHOUT LOAD (a) Connect a voltmeter and an ammeter to the charging circuit as follows. HINT: If a battery/generator tester is available, connect the tester to the charging circuit in accordance with the manufacturer's instructions. (1) Disconnect the wire from terminal B of the generator and connect it to the negative (-) ammeter lead. (2) Connect the positive (+) ammeter lead to terminal B of the generator. (3) Connect the positive (+) voltmeter lead to positive (+) battery terminal. (4) Ground the negative (-) voltmeter lead. (b) Check the charging circuit. (1) Keep the engine speed at 2,000 rpm and check the reading on the ammeter and voltmeter. Standard current: 10 A or less Standard voltage: 13.2 to 14.8 V If the result is not as specified, replace the generator. INCORRECT B000543E03 CORRECT INCORRECT B075171E06 V A Ammeter Battery Voltmeter Generator Terminal B A125200E01

2006-2011 Toyota Yaris (XP90) OEM Service & Repair Manual

You're Reading a Preview

2006-2011 Toyota Yaris (XP90) OEM Service & Repair Manual

Engine covered:

Transmission covered:

Manuals included in this bundle:

What’s Inside the 2006–2011 Toyota Yaris Service & Repair Manual

General Service Information & Repair Preparation

Maintenance Schedules & Specifications

Engine Mechanical Systems (1.5L 1NZ-FE)

Fuel, Ignition & Emissions Systems

Charging, Starting & Engine Electrical Systems

Automatic Transaxle & Drivetrain (U340E)

Suspension, Steering & Wheel Alignment

Brake System & Brake Controls

Heating, Ventilation & Air Conditioning (HVAC)

Electrical Systems & Network Diagnostics

Interior Systems & Safety Equipment

Body & Exterior Components

Lighting, Wipers & Exterior Equipment

Security & Driver Assistance Systems

Wheels, Tires & Hubs

Who This Manual Is For

Format & Compatibility

Download the 2006–2011 Toyota Yaris (XP90) OEM Service & Repair Manual

Recently Viewed