2008 Mercedes-Benz E-Class (W211) Service & Repair Manual
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
2004 ACCESSORIES/SAFETY EQUIPMENT
Mercedes-Benz - Air Bag Restraint Systems
DESCRIPTION & OPERATION
The main components of the Supplemental Restraint System (SRS) are dual-stage driver-side and passenger-
side air bag modules, side impact air bag modules, head impact air bag modules, front impact sensors, side
impact sensors, SRS control module, SRS warning light and driver-side and passenger-side Emergency
Tensioning Retractors (ETR). See COMPONENT LOCATIONS .
COMPONENT LOCATIONS
COMPONENT LOCATIONS
SERVICING
SRS AIR BAG label on driver-side door latch post indicates SRS replacement date for air bag units. All SRS
components must be thoroughly inspected, including wiring harness. Before component replacement, check for
SRS fault codes by performing system operation check. See SYSTEM OPERATION CHECK . SRS service
life is 10 years from manufactured date or 10 years from SRS replacement date after accident related repairs are
completed.
SYSTEM OPERATION CHECK
WARNING: Accidental air bag deployment is possible. Personal injury may result.
Read and follow all WARNINGS and AIR BAG SAFETY PRECAUTIONS
before working on air bag system or related components.
Component Location
AIR BAG warning light Instrument cluster
Clockspring Under steering wheel
Driver-side air bag module On steering wheel
Emergency Tensioning Retractor (ETR) Driver-side & passenger-side lower B- & C-pillars
Front impact sensor Driver-side & passenger-side engine compartment,
behind headlights
Head impact air bag modules Driver-side & passenger-side roof rails
Occupant classification sensor In passenger-side front seat cushion
Passenger-side air bag module Passenger-side instrument panel
Side impact air bag modules
(1)
Side impact sensors Driver-side & passenger-side cross member under
front seats
(1)
Depending on application, side impact air bag modules are located in front seat outer seat backs or in
front and rear door panels.
2003-2007 MERCEDES E-CLASS REPAIR MANUAL
ACCESSORIES/SAFETY EES/SAFETY EQQUIPMENT
SRS warning light indicates SRS and Emergency Tensioning Retractor (ETR) system readiness. Turn ignition
on. SRS warning light will illuminate, then turn off after approximately 4-20 seconds indicating SRS system is
functioning properly. If SRS warning light does not illuminate, illuminates while driving or is continuously
illuminated, there is a system fault. Repair malfunctioning system.
AIR BAG SAFETY PRECAUTIONS
Observe these precautions when servicing the air bag system:
When working around SRS components and before any repairs are performed, disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
Before straightening any damage to body, or before performing electrical arc-welding, disable air bag
system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
Always wear safety glasses and gloves when handling a deployed air bag module. Air bag module may
contain sodium hydroxide deposits which are irritating to the skin.
Always use control module and impact sensors made by same manufacturer. Using components produced
by different manufacturers could cause accidental air bag or ETR deployment.
DO NOT repair any portion of SRS wiring harness.
If any SRS component is dropped from a height greater than 1.6 feet (0.5 m), it must be replaced.
If SRS components show signs of damage, they must be replaced.
Always handle air bag module with trim cover facing away from your body.
Always place air bag module on workbench with trim cover up, away from loose objects.
DO NOT expose any SRS component to temperatures in excess of 212°F (100°C ).
DO NOT expose any SRS component to grease, oil or cleaning agents.
DISABLING & ACTIVATING AIR BAG SYSTEM
DISABLING SYSTEM
Turn ignition off and remove key. Disconnect negative battery cable and shield cable end.
ACTIVATING SYSTEM
Ensure no one is in vehicle. Turn ignition on. Connect negative battery cable. Go to SYSTEM OPERATION
CHECK .
DISPOSAL PROCEDURES
Several situations may arise requiring some form of disposal action, including:
Scrapping a vehicle containing deployed air bag modules and Emergency Tensioning Retractors (ETR).
Scrapping a vehicle with live air bag modules and ETRs.
Disposal of a live but electrically faulty air bag module and/or ETR.
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
Disposal of a deployed air bag module and/or ETR.
DEPLOYED AIR BAG MODULE OR EMERGENCY TENSIONING RETRACTOR (ETR)
Deployed air bag modules and ETRs can be disposed of like any other part.
SCRAPPED VEHICLE
Undeployed air bag modules and ETRs CANNOT be disposed of without first being deployed.
UNDEPLOYED AIR BAG MODULE OR EMERGENCY TENSIONING RETRACTOR (ETR)
Undeployed air bag modules and Emergency Tensioning Retractor (ETR) seat belts CANNOT be disposed of
without first being deployed.
ON-VEHICLE DEPLOYMENT (SCRAPPED VEHICLE)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Park vehicle outdoors with at least 33
feet (10 m) of open space around vehicle. Disable air bag system. See DISABLING & ACTIVATING
AIR BAG SYSTEM . Place a fully-charged 12-volt battery 33 feet (10 m) from vehicle.
2. Disconnect all air bag module and Emergency Tensioning Retractor (ETR) connectors. See REMOVAL
& INSTALLATION . Fabricate a deployment harness using 2 wires, each 33 feet (10 m) in length.
Connect deployment harness to selected component to be deployed. Twist opposite ends of deployment
harness together to prevent accidental deployment. Dual stage air bag modules will require 2 deployment
harnesses.
3. Ensure no one is within 33 feet (10 m) of air bag module. Untwist ends of deployment harness. Connect
wires to battery. Component should deploy. Repeat deployment procedure for remaining components.
OFF-VEHICLE DEPLOYMENT
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM . Remove component to be deployed. See
REMOVAL & INSTALLATION . Place component in the center of an area with at least 33 feet (10 m)
of clearance on all sides.
2. Attach component to a suitable object, such as a tire and wheel assembly, to prevent movement. Fabricate
a deployment harness using 2 wires, each 33 feet (10 m) in length. Connect deployment harness to
WARNING: Components are very hot after deployment. Personal injury may result.
Allow sufficient time for components to cool before touching.
NOTE: Deploy only one component at a time.
WARNING: Components are very hot after deployment. Personal injury may result.
Allow sufficient time for components to cool before touching.
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
selected component. Twist opposite ends of deployment harness together to prevent accidental
deployment. Dual stage air bag modules will require 2 deployment harnesses.
3. Ensure no one is within 33 feet (10 m) of component. Untwist ends of deployment harness. Connect wires
to battery. Component should deploy. Repeat deployment procedure for remaining components.
POST-COLLISION INSPECTION
When a vehicle has been involved in a collision, certain components of the passive restraint system must be
inspected or replaced. See AIR BAG/SRS COMPONENT INSPECTION & REPLACEMENT TABLES
article in the GENERAL INFORMATION section.
REMOVAL & INSTALLATION
CLOCKSPRING
Information is not available.
CONTROL MODULE
Removal & Installation
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove ashtray assembly from center console. Remove control module screws. Pull control module up
and out of center console. Disconnect control module electrical connectors. Remove control module.
3. To install, reverse removal procedure. Tighten control module bolts to specification. See TORQUE
SPECIFICATIONS . Activate air bag system. Program control module. See DIAGNOSTICS .
DRIVER-SIDE AIR BAG MODULE
Removal & Installation
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Move steering wheel to full rearward position. Using Torx Bit (126-589-00-10-00), remove bolts securing
driver-side air bag module to steering wheel from rear of steering wheel. Pull driver-side air bag module
away from steering wheel. Disconnect driver-side air bag module electrical connectors. Remove driver-
side air bag module.
3. To install, reverse removal procedure. Tighten driver-side air bag module bolts to specification. See
TORQUE SPECIFICATIONS . Activate air bag system. Read diagnostic codes and erase memory. See
DIAGNOSTICS .
WARNING: Accidental air bag deployment is possible. Personal injury may result.
Read and follow all WARNINGS and AIR BAG SAFETY PRECAUTIONS
before working on air bag system or related components.
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
EMERGENCY TENSIONING RETRACTOR (ETR)
Removal & Installation (Front Seat)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove appropriate B-pillar trim panel. Remove nut from upper seat belt guide bracket and remove
bracket. Disconnect ETR electrical connector. Remove ETR bolts. Remove ETR.
3. To install, reverse removal procedure. Tighten ETR bolts and upper seat belt bracket nut to specification.
See TORQUE SPECIFICATIONS . Activate air bag system. Read diagnostic codes and erase memory.
See DIAGNOSTICS .
Removal & Installation (Rear Seat)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove appropriate quarter panel trim. Remove nut from upper rear seat belt guide bracket. Remove rear
seat belt guide bracket. Disconnect ETR electrical connector. Remove bolts from ETR. Remove ETR.
3. To install, reverse removal procedure. Activate air bag system. Tighten ETR bolts and upper rear seat belt
guide bracket to specification. See TORQUE SPECIFICATIONS . Read diagnostic codes and erase
memory. See DIAGNOSTICS .
FRONT IMPACT SENSOR (REAR SEAT)
Removal & Installation
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove air intake hose. Disconnect electrical connector from hot water circulation pump. Remove bolts
from appropriate front impact sensor. Disconnect front impact sensor electrical connector. Remove front
impact sensor.
3. To install, reverse removal procedure. Tighten front impact sensor bolts to specification. See TORQUE
SPECIFICATIONS . Activate air bag system. Read diagnostic codes and erase memory. See
DIAGNOSTICS .
HEAD IMPACT AIR BAG MODULE
Removal & Installation (Sedan)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove headliner. See HEADLINER . Disconnect appropriate head impact air bag module electrical
connector. Remove nuts securing head impact air bag module to roof rail. Detach head impact air bag
module from clips. Remove head impact air bag module.
3. To install, reverse removal procedure. Tighten head impact nuts and bolts to specification. See TORQUE
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
SPECIFICATIONS . Activate air bag system. Read diagnostic codes and erase memory. See
DIAGNOSTICS .
Removal & Installation (Wagon)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove headliner. See HEADLINER . Disconnect appropriate head impact air bag module electrical
connector. Remove nuts from head impact air bag module. Remove check strap screws. Using Wedge
(110-589-03-59-00), unclip head impact air bag module from roof rail clips. Remove head impact air bag
module.
3. To install, reverse removal procedure. Use NEW head impact air bag module supports. Tighten head
impact air bag module nuts and bolts to specification. See TORQUE SPECIFICATIONS . Activate air
bag system. Read diagnostic codes and erase memory. See DIAGNOSTICS .
HEADLINER (WAGON)
Removal & Installation (Sedan)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Open tilting/sliding roof. Disable air bag
system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove rail from tilting/sliding roof. Remove inside rear view mirror assembly. Remove overhead
control panel module. Remove sun visors and mounting brackets. Remove rear dome light. Remove left
and right grab handles. Remove load anchors. Remove door edge guards. Remove left and right A-, B-
and C-pillar trim panels. Lower front seat backrests. Remove head restraints from rear seats.
3. Tape edge of center console to prevent damage from headliner. See Fig. 1 . Unhook headliner from
tilting/sliding roof assembly. Slide headliner forward. Carefully lower headliner, rotate and remove
through passenger-side front door. See Fig. 2 .
4. To install, reverse removal procedure. Activate air bag system. Read diagnostic codes and erase memory.
See DIAGNOSTICS .
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
Fig. 1: Identifying Tape On Edge Of Center Console
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
Fig. 2: Identifying Headliner
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Removal & Installation (Wagon)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Open tilting/sliding roof. Disable air bag
system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove left A-pillar trim panel. Remove left front grip handle. Remove left front door edge guard.
Remove left B-pillar trim panel. Remove left rear door edge guard. Remove left rear grip handle. Remove
left and right safety net screws. Remove safety net frame.
3. Remove left C-pillar and D-pillar trim. Remove left quarter panel trim. Remove right rear grip handle.
Remove right rear door edge guard. Remove right B-pillar trim panel. Remove right front door edge
guard. Remove right A-pillar trim panel. Remove right front grip handle.
4. Remove right D-pillar trim panel. Remove right quarter panel trim. Remove left C-pillar trim panel.
Remove rear dome light. Remove left and right sun visors. Remove overhead control panel module.
Remove inside rear view mirror assembly. Remove front sealing strip from tilting/sliding roof.
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
wire connectors, located on left D-pillar. Release headliner retaining clips. Slide headliner towards front
of vehicle until retaining hooks disconnect. Carefully lower headliner. Remove headliner through rear of
vehicle.
5. To install, reverse removal procedure. Tighten safety net screws to specification. See TORQUE
SPECIFICATIONS . Activate air bag system. Read diagnostic codes and erase memory. See
DIAGNOSTICS .
OCCUPANT CLASSIFICATION SENSOR (WAGON)
Removal & Installation
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Open tilting/sliding roof. Disable air bag
system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove front seat cushion cover. Unhook clips on seat assembly as necessary. Remove occupant
classification sensor by pulling upward, out of seat cushion. Ensure electrical connector is not damaged
during removal while pulling through seat cushion.
3. To install, reverse removal procedure. Ensure occupant classification sensor is positioned evenly and
squarely on passenger seat. Activate air bag system. Read diagnostic codes and erase memory. See
DIAGNOSTICS .
UPPER INSTRUMENT PANEL
Removal & Installation
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove instrument cluster. Remove left A-pillar trim panel. Using Wedge (110-589-03-59-00), remove
left end panel from instrument panel. Remove trim strip, located below instrument cluster opening.
Remove right A-pillar trim panel. Using wedge, remove right end panel from instrument panel. Remove
center instrument panel trim plate and control head assembly.
3. Remove bolts securing upper instrument panel to main instrument panel. Lift up on upper instrument
panel. Disconnect electrical connectors. Remove upper section of instrument panel.
4. To install, reverse removal procedure. Tighten passenger-side air bag module nuts to specification. See
TORQUE SPECIFICATIONS . Activate air bag system. Read diagnostic codes and erase memory. See
DIAGNOSTICS .
PASSENGER-SIDE AIR BAG MODULE
Removal & Installation
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
DISABLING & ACTIVATING AIR BAG SYSTEM .
2. Remove upper section of instrument panel. See UPPER INSTRUMENT PANEL . Disconnect
passenger-side air bag module electrical connectors. Remove bolts securing passenger-side air bag
module to instrument panel crossmember. Remove passenger-side air bag module. See Fig. 3 .
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
3. To install, reverse removal procedure. Tighten passenger-side air bag module bolts to specification. See
TORQUE SPECIFICATIONS . Activate air bag system. Read diagnostic codes and erase memory. See
DIAGNOSTICS .
Fig. 3: Identifying Passenger - side Air Bag Module
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
SIDE IMPACT AIR BAG MODULE
Removal & Installation (Door Mounted)
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Disable air bag system. See
2004 Mercedes-Benz E320 4Matic
2004 ACCESSORIES/SAFETY EQUIPMENT Mercedes-Benz - Air Bag Restraint Systems
You're Reading a Preview
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$37.99
Viewed 11 Times Today
Secure transaction
What's Included?
Lifetime Access
Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual
$37.99
Get your hands on the 2008 Mercedes-Benz E-Class (W211) Service & Repair Manual. This manual provides comprehensive instructions and procedures to fix problems in your vehicle. Whether you're a professional mechanic or a DIY enthusiast, these manuals can be invaluable for immediate car repairs. The manual contains technical data, diagrams, a complete list of car parts, and pictures, making it easy for even novice car mechanics to follow. It covers maintenance, engine, control system, mechanical, fuel service specifications, emission control, and much more. The repair manual is compatible with all versions of Windows and Mac, and it's printable. With this manual, you can save time and money by learning to repair different parts of your car on your own. It's a valuable resource that allows you to stay up-to-date and gain more knowledge about your vehicle. Say goodbye to flipping through books and rely on this easy-to-use manual for all your repair needs.
- Complete step-by-step instructions
- Diagrams, illustrations, and wiring schematics
- Specifications to completely repair your vehicle with ease
- Print only the pages and diagrams you require
- Factory highly detailed repair manuals
- Compatible with Windows and Mac
Auto Repair Manuals can be your go-to solution for maintaining, servicing, diagnosing, and repairing your vehicle. It's a fun and empowering activity that allows you to take charge of your car's maintenance. With all pages printable, you can keep the manual safe on your PC and print the necessary pages in a matter of seconds. Take control of your car's repairs and enjoy the convenience of having all the information you need at your fingertips.
